DRAGON GAUGE 611BL Series

Contents

DRAGON GAUGE 2'' 52MM Multi-Function Digital Gauge User Manual

Models: Boost, Water Temp, Oil Temp, Volt, Tachometer, Oil Pressure

1. Introduction

Thank you for choosing the DRAGON GAUGE 2'' 52MM Digital Gauge. This manual provides essential information for the proper installation, operation, and maintenance of your new automotive gauge. Please read this manual thoroughly before installation and keep it for future reference.

These gauges are designed to provide accurate, real-time readings of various engine parameters, featuring a clear digital blue LED display for optimal visibility.

2. Safety Information

  • Always disconnect the vehicle's battery before performing any electrical work to prevent short circuits and electrical shock.
  • Ensure all wiring connections are secure and properly insulated to prevent electrical hazards.
  • Mount the gauge in a location that does not obstruct the driver's view or interfere with vehicle controls.
  • If you are unsure about any part of the installation process, consult a qualified automotive technician.
  • Do not expose the gauge to extreme temperatures, direct water spray, or harsh chemicals.

3. Package Contents

Depending on the specific gauge and options purchased, your package may include:

  • Digital Gauge Unit (e.g., Boost, Water Temp, Oil Temp, Volt, Tachometer, Oil Pressure)
  • Wiring Harness
  • Corresponding Sensor (e.g., temperature sensor, pressure sensor)
  • Gauge Pod (Single, Dual, Triple, or Gauge Holder, if selected)
  • Installation Instructions (refer to this manual)
Wiring Harness
Figure 1: Included Wiring Harness
Temperature Sensor
Figure 2: Example Sensor (Temperature Sensor shown)
Single Gauge Pod
Figure 3: Example Gauge Pod (Single Pod shown)

4. Setup and Installation

4.1 Physical Installation

  1. Choose a suitable mounting location on your vehicle's dashboard or A-pillar that does not obstruct your view or interfere with driving.
  2. The gauge has a diameter of 52mm (2 inches) for mounting. The front bezel diameter is approximately 55mm, and the depth is 40mm.
  3. If using a gauge pod, secure the pod to the chosen location and then insert the gauge into the pod.
  4. Ensure the gauge is firmly seated and secured.
Gauge Front Diameter 55mm
Figure 4: Gauge Front Diameter (approx. 55mm)
Gauge Depth 40mm
Figure 5: Gauge Depth (40mm)
Gauge Back Diameter 52mm
Figure 6: Gauge Mounting Diameter (52mm)

4.2 Electrical Installation

Refer to the wiring diagram below for specific connections. Always ensure the vehicle's battery is disconnected before making electrical connections.

Electrical Wiring Diagram for Gauges
Figure 7: Electrical Installation Instructions for Various Gauges

General Wiring Connections:

  • RED Wire: Connect to Ignition Switch 12V(+) (switched power).
  • BLACK Wire: Connect to Battery(-) or a reliable chassis ground.
  • GREEN Wire: Connect to the signal output of the respective sensor.

Specific Gauge Wiring (refer to Figure 7 for visual aid):

Boost/Vacuum Gauge (6-1-3)

  • RED: To Ignition Switch 12V(+)
  • BLACK: To Battery(-)
  • GREEN: To Sensor
  • Connect nylon tubing to the sensor and manifold.

Tachometer Gauge (6-R)

  • RED: To Ignition Switch 12V(+)
  • BLACK: To Battery(-)
  • GREEN: To Ignition Coil (-) or ECU Tachometer Signal.
  • Adjust cylinder choice if applicable.

Oil/Water Temperature Gauge (6-4-5)

  • RED: To Ignition Switch 12V(+)
  • BLACK: To Battery(-)
  • GREEN: To Temp Sensor.

Oil Pressure Gauge (6-6)

  • RED: To Ignition Switch 12V(+)
  • BLACK: To Battery(-)
  • GREEN: To Pressure Sensor.

Voltmeter Gauge (6-7)

  • RED: To Ignition Switch 12V(+)
  • BLACK: To Battery(-)
  • (No separate sensor wire needed as it measures voltage directly from power input)

After all connections are made, reconnect the vehicle's battery and test the gauge functionality.

5. Operating Instructions

  1. Turn the vehicle's ignition to the 'ON' or 'ACC' position.
  2. The gauge will power on, illuminate with a blue LED, and display the current reading for its respective parameter.
  3. Readings are displayed digitally. Units may vary (e.g., Boost in BAR or PSI, Temperature in °C, Oil Pressure in PSI/BAR, Voltage in Volts, RPM).
  4. Some gauges may feature a 'WARNING' indicator. Consult specific gauge instructions or seller for details on setting warning thresholds if applicable.

6. Maintenance

  • Cleaning: To clean the gauge face, use a soft, dry, lint-free cloth. Do not use abrasive cleaners or solvents.
  • Sensor Inspection: Periodically check the sensor and its wiring connections for any signs of damage, corrosion, or loose connections.
  • Wiring Inspection: Ensure all electrical connections remain secure and insulated.

7. Troubleshooting

Problem Possible Cause Solution
Gauge does not power on/light up No power to the gauge; loose RED or BLACK wire connection; blown fuse. Check RED wire for 12V power; ensure BLACK wire has good ground; check inline fuse if present.
Gauge displays incorrect or erratic readings Loose or faulty sensor connection; damaged sensor; incorrect sensor type. Check GREEN wire connection to sensor; inspect sensor for damage; ensure correct sensor is used for the gauge.
Gauge is too bright at night No dimming feature or personal preference. Consider repositioning or adding an external dimmer if compatible (not typically built-in).
Gauge shows '---' or 'ERR' Sensor not connected or faulty; out of range reading. Verify sensor connection; check sensor functionality.

8. Specifications

Feature Specification
Gauge Diameter 52mm (2 inches)
Gauge Depth 40mm
Item Weight 0.4 kg
Material Aluminum (AL)
Special Features Boost, Water Temp, Oil Temp, Volt, RPM, Oil Pressure (model dependent)
Display Type Digital Blue LED
Placement on Vehicle Front
Manufacturer Part Number 611BL Series
Origin Mainland China

9. User Tips

  • Visibility: While the blue LED display is generally clear, some users find it quite bright at night. Consider your preferred brightness when choosing a mounting location.
  • Fitment: The gauges are designed to fit well in standard 52mm gauge pods and vehicle dashboards.
  • Completeness: Each gauge typically comes complete with its sensor and wiring harness, ready for installation.

10. Frequently Asked Questions (FAQ)

Q: Does the gauge come with the sensor and display?
A: Yes, typically each gauge unit includes the display, the necessary sensor, and a wiring harness.
Q: Is the oil pressure gauge in BAR or PSI?
A: The specific units (BAR or PSI) may vary by model or region. Please check the product description or contact the seller for the exact units of the oil pressure gauge you intend to purchase.
Q: Can these gauges be used on a motorcycle?
A: These gauges are primarily designed for automotive applications (cars). While technically possible, fitment and electrical compatibility for motorcycles may vary and are not officially supported.
Q: How many gauges are included in one purchase?
A: Each selection (e.g., 'Boost Gauge', 'Water Temp Gauge', 'Single Pod') corresponds to one item. If you need multiple gauges or pods, you must select each one individually.

11. Warranty and Support

For warranty information, technical support, or any product-related inquiries, please contact your original seller or the manufacturer directly. Keep your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.