SHIMANO RD-M360, RD-M3020, RD-M310

Contents

SHIMANO Acera RD-M360 M3020 ALTUS RD-M310 Rear Derailleur Instruction Manual

For 7/8 Speed Mountain Bicycles

1. Safety Information

CE Mark

Warning Symbol & Notice

WARNING:

  • This product is not a toy and is not suitable for children under 16 years old without adult supervision.
  • Keep all small parts (e.g., screws, pulleys) away from infants and toddlers to avoid choking hazards.
  • Always wear appropriate protective gear (helmet, gloves, knee pads) when operating the bicycle with this derailleur.
  • Do not use the product in traffic without proper training.
  • Ensure the derailleur is correctly installed and adjusted before use. Improper installation may cause chain slippage, leading to falls or serious injury.
  • Do not modify the derailleur's structure or components. Unauthorized modifications void compliance and safety guarantees.
  • This product is not intended for use with children's bicycles (refer to EN 14765 for children-specific requirements).
  • Keep the derailleur away from corrosive substances (acids, solvents) and extreme temperatures to prevent mechanical failure.

Additional Safety Notes

Regularly inspect the derailleur for wear, damage, or loose connections. Replace worn parts immediately using genuine Shimano accessories.

Applicable Regulations & Harmonized Standards

This product complies with the following EU regulations and standards:

  • General Product Safety Directive (GPSD): 2001/95/EC
  • Mechanical Directive (MD): 2006/42/EC

Harmonized Standards:

  • EN ISO 4210-2:2015 (Bicycle safety requirements for city, trekking, mountain bikes)
  • EN 14781:2015 (Racing bicycle specific safety standards)
  • REACH Regulation (EC) No 1907/2006 (Restriction of hazardous substances)

Usage Restrictions

Not Suitable For:

  • Children under 16 years old (without adult supervision)
  • Bicycles with wheel sizes below 26" or above 29"
  • Electric bicycles with motor power exceeding 250W
  • Off-road use in extreme conditions (e.g., rock climbing, steep descents >30°)
  • Environmental Restrictions: Do not use in saltwater environments (e.g., coastal areas) without proper corrosion protection.

2. Product Overview

The SHIMANO Acera RD-M360, RD-M3020, and ALTUS RD-M310 are mechanical rear derailleurs designed for mountain bicycles. These models support 7-speed and 8-speed drivetrains, offering reliable and smooth gear changes for various riding conditions.

SHIMANO ALTUS RD-M310 black rear derailleur
SHIMANO ALTUS RD-M310 (Black)
SHIMANO ALTUS RD-M310 silver rear derailleur
SHIMANO ALTUS RD-M310 (Silver)
SHIMANO Acera RD-M3020 SGS rear derailleur
SHIMANO Acera RD-M3020 SGS
SHIMANO Acera RD-M360 SGS rear derailleur
SHIMANO Acera RD-M360 SGS

3. Specifications

Feature Specification
Brand NameSHIMANO
TypeRear Derailleur
ComponentsDerailleurs
Derailleur Groupset TypeMechanical Derailleur system
Total CapacityFor 7/8 speed
Gears7 Speed / 8 Speed
MaterialAlloy
OriginVaries by batch (e.g., Indonesia, Japan)
High-concerned chemicalNone

Model-Specific Details:

SHIMANO Acera RD-M3020-8

  • Series: ACERA M3000 Series
  • Colour: Black
  • Compatible Chains: HG 8/7/6 Speed
  • Total value of tooth change range: 45T
  • Cord Conditioner: Yes
  • Base: Direct Attach (Traditional)
  • Link bushing with fluorine coating: 1
  • Low-position sprocket maximum tooth: 40T
  • Minimum tooth of low sprocket: 30T
  • Difference between maximum and minimum chainring teeth: 20T
  • Idler_Recessed Idler Screw: Yes
  • Guide wheel_tooth combination: 11T
  • Guide: SGS
  • Top Standard Spring Type: Dual Servo
  • High-position sprocket maximum tooth: 12T
  • Minimum tooth of high-position sprocket: 11T
  • Rear Shift: 8/7

SHIMANO ALTUS RD-M310

  • Model Number: RD-M310
  • Speed: 7S/8S
  • Weight: Approximately 286g

SHIMANO Acera RD-M360 SGS

  • Model Number: RD-M360
  • Speed: 7/8 Speed
  • Weight: Approximately 300-310g
  • Cage: Long Cage (SGS)
  • Cassette Compatibility: Maximum sprocket up to 34T
SHIMANO RD-M310 black on a scale showing 286.0g
RD-M310 black weight measurement (286.0g)
SHIMANO RD-M360 on a scale showing 304.6g
RD-M360 weight measurement (304.6g)

4. Installation

Proper installation of your SHIMANO rear derailleur is crucial for safe and efficient operation. If you are unsure about any steps, it is highly recommended to seek assistance from a qualified bicycle mechanic.

General Installation Steps:

  1. Mount the Derailleur: Securely attach the derailleur to the derailleur hanger on your bicycle frame. Ensure it is properly aligned.
  2. Install the Chain: Route the bicycle chain through the derailleur's guide and tension pulleys.
  3. Connect the Shift Cable: Attach the shift cable to the derailleur and secure it according to the manufacturer's specifications.
  4. Adjust Limit Screws: Set the high (H) and low (L) limit screws to prevent the chain from shifting beyond the smallest and largest cogs, respectively.
  5. Adjust B-Tension Screw: Adjust the B-tension screw to ensure proper clearance between the upper guide pulley and the largest cog.
  6. Fine-Tune Shifting: Use the barrel adjuster on the shifter or derailleur to fine-tune cable tension for smooth and precise shifting across all gears.

Important: Always refer to detailed SHIMANO technical documentation for specific installation instructions for your exact model. Incorrect installation can lead to poor performance or serious injury.

Installed rear derailleur on a bicycle
Example of an installed rear derailleur on a bicycle.

5. Operation

The SHIMANO rear derailleur is designed to provide smooth and reliable gear changes for your bicycle. It works in conjunction with your rear cassette and shifter to move the chain between different cogs, allowing you to select the appropriate gear ratio for varying terrain and effort levels.

Shifting Gears:

  • Use your right-hand shifter to control the rear derailleur.
  • To shift to a harder (smaller) gear, typically press the smaller lever or button.
  • To shift to an easier (larger) gear, typically press the larger lever or button.
  • Always pedal lightly while shifting to ensure smooth transitions and prevent damage to the drivetrain components.

These derailleurs are compatible with 7-speed and 8-speed systems, providing a versatile range for mountain biking.

6. Maintenance

Regular maintenance will extend the life and performance of your SHIMANO rear derailleur.

Maintenance Schedule:

  • Every 500km or 3 months (whichever comes first): Inspect and lubricate the derailleur.

Inspection and Care:

  • Inspect for Wear and Damage: Regularly check the derailleur body, cage, and pulleys for any signs of wear, cracks, bends, or damage.
  • Check for Loose Connections: Ensure all bolts and screws are securely tightened.
  • Lubrication: Apply a suitable bicycle chain lubricant to the pivot points of the derailleur and the pulley bearings. Wipe off any excess lubricant.
  • Cleaning: Keep the derailleur clean from dirt, mud, and grime. Use a brush and appropriate degreaser if necessary, then rinse and re-lubricate.
  • Replacement Parts: Replace worn or damaged parts immediately using genuine Shimano accessories to maintain optimal performance and safety.

7. Troubleshooting

Here are some common issues and their potential solutions:

  • Difficulty Shifting / Poor Shifting Performance:
    • Check if the derailleur is properly adjusted (limit screws, B-tension, cable tension).
    • Inspect the shift cable and housing for kinks, fraying, or excessive friction.
    • Ensure the derailleur hanger is not bent.
    • Clean and lubricate the chain and derailleur pivots.
  • Chain Skipping or Jumping Gears:
    • This can be caused by incorrect derailleur adjustment, a worn chain, worn cassette cogs, or worn derailleur pulleys.
    • Check for excessive play in the derailleur's plastic parts or pulleys, which may indicate wear and require replacement.
    • Ensure the chain is compatible with your drivetrain (e.g., HG 8/7/6 Speed for RD-M3020).
  • Derailleur Rubbing Against Chain or Spokes:
    • Adjust the limit screws (H and L) to ensure the derailleur cage is properly aligned with the cassette.
    • Check for a bent derailleur hanger.
  • Noise from Derailleur:
    • Often due to lack of lubrication, dirt, or incorrect adjustment. Clean, lubricate, and adjust as needed.
    • Check for worn pulleys or loose components.

8. User Tips

  • Initial Inspection: Upon receiving your derailleur, visually inspect all components for any signs of damage or manufacturing defects before installation.
  • Professional Installation: While installation can be straightforward for experienced users, professional installation and adjustment are recommended to ensure optimal performance and safety. Derailleurs typically require adjustment after installation.
  • Durability Consideration: Some users suggest that models with metal gears may offer enhanced durability compared to those with plastic components.
  • Smooth Operation: When properly installed and adjusted, these derailleurs are noted for their smooth chain operation and reliable shifting.

9. Warranty & Support

Manufacturer Information:

Name: Shimano Inc.
Address: 3-1-1 Sakai-cho, Sakai-ku, Osaka, Japan
Contact: support@shimano.com

EU Responsible Person (Authorized Representative):

Name: MJCM SARL
Country: France
Address: 78 avenue des Champs Elysees, Bureau 326, 75008 Paris, France
Phone: +33-752907452
Email: mjcm190928@gmail.com

A complete copy of the EU Declaration of Conformity (DoC) is available upon request from the EU Responsible Person.

For additional item guides and documents, please refer to the official PDF user manual: User manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.