Introduction
This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your Glixal GY6 125cc 150cc Variator Guide Slide Set. These guide slides are crucial components of your scooter's Continuously Variable Transmission (CVT) system, ensuring smooth and efficient power delivery. Proper installation and maintenance are essential for optimal performance and longevity.
Figure 1: Glixal GY6 125cc 150cc Variator Guide Slide Set (3 pieces)
Warnings & Safety Instructions
Please read all safety instructions carefully before proceeding with installation or maintenance.
- Heat Resistance: These slides are manufactured from Glass-Fiber Reinforced Polyamide (PA66-GF) designed to withstand continuous friction and temperatures exceeding 130°C. Substituting with standard plastics is a severe safety risk.
- Wear Limits: As they wear down, they effectively become "lighter," altering the shift point. Worn slides cause erratic shifting, vibration, and reduced top speed. Inspect every 6,000 km.
- Lubrication Requirement: Slides must be lubricated with high-temperature Molybdenum (Moly) grease. Running them dry causes excessive friction heat, leading to melting and rapid wear. Do not use standard lithium grease (it melts and flings off).
- Set Consistency: All 3 slides must be identical in weight and wear. Never mix old and new slides. Uneven wear causes the ramp plate to tilt, creating severe vibration and uneven belt wear.
- Ramp Plate Condition: Before installing new slides, inspect the metal channels of the ramp plate. If there are deep grooves, burrs, or blueing (heat damage), the ramp plate must be replaced. New slides on damaged ramps will fail immediately.
Product Overview & Compatibility
The Glixal Variator Guide Slide Set is designed for GY6 125cc and 150cc engines, specifically models 152QMI and 157QMJ. These parts are commonly found in a wide range of Chinese scooters, mopeds, ATVs, and Go-Karts.
Compatible with many models from brands such as: Blade, Kinroad, Twister Hammerhead, Carter Talon, Dazon, Roketa, DUNE, Baja kart, Kasea, KPX, SUNL, Aimex, Alpha sports, Avanti, Bam X, Baotian, Bashan, BMS, BMX, Boreem, Eagle, CF Moto, Cross Runner, Cool Sports, Diamo, E Ton, Eagle, Fushin, Fly, GMI, Hensim, Hi-bird, Baja, Ice Bear, Jackel, Jet Moto, JCL, Taotao, Peace, JM Star, Jonway, Kazuma, Keeway, KMD, Kymco, Lance, Lifan, Linhai, Loncin, Longbo, Fuxin, Maxtrade, MDI, Meitien, Motofino, Motorino, NST, Panterra, Panther, Qlink Yiben, Red Streak, Redcat, Roketa, Schwinn, Seaseng, Strada, SYM, Tank, Terminator, Tomberlin, TNG, United Motors, Vento, Verucci, Wildfire, X-Treme, Yamati, ZNEN, and Zongshen.
Figure 2: Example of a scooter that may use this variator guide slide set.
Specifications
| Attribute | Value |
|---|---|
| Brand Name | Glixal |
| Model Name | GY6 125cc 150cc |
| Engine Model | 152QMI 157QMJ |
| Item Type | Variomat & Parts |
| Used for | Chinese Scooter Moped Engine |
| Material | Plastic (Glass-Fiber Reinforced Polyamide PA66-GF) |
| Stroke | 4 Stroke |
| Item Weight | 0.1kg |
| External Testing Certification | ISO9001 |
| Product Condition | 100% New |
| Origin | Mainland China |
| Package Length | 10 cm |
| Package Width | 10 cm |
| Package Height | 5 cm |
| Package Weight | 0.02 kg |
Installation Instructions
This section outlines the steps for replacing your variator guide slides. Always ensure your engine is cool before starting any work.
Phase 1: Disassembly
- Preparation: Place your scooter on its center stand. Ensure the engine is cool to the touch.
- Remove CVT Cover: Carefully remove the bolts securing the CVT cover. Tap the cover gently to break any seal, then remove it. Discard the old gasket.
- Secure Assembly: Install a Fan/Variator Holder Tool to prevent the variator from rotating during nut removal.
-
Remove Variator Nut:
- WARNING: The GY6 Variator Nut is typically LEFT-HAND THREAD (Reverse). This means you turn CLOCKWISE to loosen (Righty-Loosey).
- Verify the specific thread direction for your model before applying force.
- Remove Components: Once the nut is off, remove the washer, cooling fan, drive belt, and the Variator Assembly (Ramp Plate + Hub).
Phase 2: Inspection & Cleaning (CRITICAL)
-
Inspect Ramp Plate Channels: Look closely at the 3 triangular channels where the slides sit.
- Acceptable: Smooth metal with slight polishing.
- Unacceptable: Deep gouges, ridges, blue/discolored metal (indicating overheating), or cracked edges. If any damage is present, the entire Ramp Plate must be replaced. New slides will not function correctly on damaged ramps.
- Clean Thoroughly: Use brake cleaner to remove all old grease, black rubber dust, and dirt from the ramp plate channels and the variator hub. Dry completely. Any grit left inside will act as sandpaper on the new slides, causing premature wear.
Phase 3: Installation of New Slides
- Weigh the Slides: Use a digital scale to weigh all 3 new slides. They should be within 0.1g of each other. If one is significantly different, do not use that particular set.
-
Determine Orientation:
- Examine the slide shape. One side is typically curved to match the ramp, and the other is flat or has a specific lip.
- Look for an arrow molded into the plastic indicating the direction of rotation. The curved/concave side generally faces the ramp plate channel, while the flat side often faces the outer edge or follows the spiral direction.
- If you removed old slides, note their exact orientation before removal and match the new slides accordingly.
- Apply Grease: Apply a thin, even coat of High-Temp CVT Grease to the contact surfaces of the slides and inside the ramp plate channels. Avoid applying too much grease, as excess can attract dirt and debris.
-
Insert Slides: Slide all 3 pieces into their respective channels.
- Test Movement: Push each slide up and down the ramp by hand. They must move smoothly and freely without binding or sticking. If a slide sticks, re-check its orientation or clean the channel again.
Phase 4: Reassembly
- Mount Variator: Slide the entire variator assembly back onto the crankshaft splines.
- Install Belt: Route the drive belt over the variator, pushing it deep into the smallest diameter to allow for easier installation of the outer half.
- Install Fan & Nut: Install the cooling fan, ensuring its vanes face the correct direction for airflow. Then, install the washer and the variator nut.
-
Tighten Nut:
- Hold the assembly with the holder tool.
- For LEFT-HAND THREAD nuts, turn COUNTER-CLOCKWISE to tighten (Lefty-Tighty).
- Torque the nut to 45 Nm. Always refer to your scooter's official service manual for model-specific torque values.
- Seal Case: Clean the mating surfaces perfectly. Install a new CVT cover gasket.
- Close Cover: Torque the CVT cover bolts evenly in a star pattern to 10-12 Nm.
Testing
After installation, perform the following tests to ensure proper function:
- Idle Check: Start the engine. Listen for any grinding or clicking noises coming from the CVT area.
- Rev Test: Hold the rear brake firmly and gently rev the engine. The RPM should rise smoothly without hesitation or unusual sounds.
- Road Test: Accelerate from a complete stop. The engine should rev up, then drop slightly as the slides move up the ramps and the "gear" shifts. Observe for smooth acceleration and proper shifting.
- Heat Check: After approximately 10 minutes of operation, ensure the CVT cover is warm but not smoking or emitting a smell of burning plastic.
Maintenance
- Regular Inspection: Inspect the variator guide slides for wear every 6,000 km. Replace them if they show significant wear, as worn slides can lead to erratic shifting, vibration, and reduced top speed.
- Lubrication: Always lubricate the slides and ramp plate channels with high-temperature Molybdenum (Moly) grease during installation and any subsequent maintenance. Avoid using standard lithium grease.
Troubleshooting
If you encounter issues after installing the new variator guide slides, consider the following:
- Screaming high RPM, no speed: This symptom often indicates that the slides are too light or are stuck. Re-check installation and slide weight.
- Bogging, won't rev: This can occur if the slides are too heavy for your setup. Ensure correct slide weight for your engine and desired performance.
- Vibration: Persistent vibration may suggest that the slides were installed incorrectly or that there is uneven wear among the slides. Re-inspect orientation and consistency.
- Unusual Noises: Grinding or clicking sounds from the CVT area during idle or revving may indicate improper installation, damaged components, or lack of lubrication.
User Tips
-
Color Variation: Be aware that the color of the guide slides may vary from product images. Some users have reported receiving red slides instead of black. This typically does not affect the product's functionality.
Figure 3: Example of red variator guide slides as received by a user.
- Compatibility Check: Always double-check the compatibility of these slides with your specific scooter model and engine type before purchase. For instance, these slides may not be compatible with a 2023 Vespa Sprint 125.
- Variator Nut Thread: The variator nut on GY6 engines is commonly a LEFT-HAND THREAD. Always confirm the thread direction for your specific model to avoid stripping the threads during removal or installation.
Warranty & Support
For model-specific torque values and additional detailed information, please refer to your scooter's official service manual.
A PDF version of the user manual is available for download: Glixal Variator Guide Slide Set User Manual (PDF)
Manufacturer Information:
YIWU SHENGQI IMP&EXP CO.,LTDUnit 2, Building 71, Gongdatang No.1 District
Yiwu City, Zhejiang Province
Email: atmotorparts@outlook.com
EU Authorized Representative:
SUCCESS COURIER SLCALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3
Fuenlabrada, Madrid, 28947 Spain
Tel: 910602659