1. Introduction
The DM320T is a digital stepper drive designed for simple setup and operation. It utilizes advanced stepper control technology to smoothly power 2-phase and 4-phase stepper motors, ensuring optimal torque with reduced motor heating and noise. This drive operates on 10-30VDC and can output up to 2.2A. Microstep resolution and output current are configured via DIP switches, making the DM320T suitable for applications requiring basic step and direction control for NEMA11, 14, 16, and 17 stepper motors.
1.1 Features
- Anti-Resonance for optimal torque, smooth motion, low motor heating, and noise.
- Motor auto-identification and parameter auto-configuration.
- Step & direction (PUL/DIR) control.
- Multi-Stepping for smooth motor movement.
- Optically isolated inputs.
- Input voltage: 10-30VDC.
- 8 selectable micro-step resolutions (400-12800) via DIP switches.
- 8 selectable output current settings (0.3 - 2.2A) via DIP switches.
- Soft-start with no "jump" when powered on.
- Pulse input frequency up to 60 KHz.
- Automatic idle-current reduction.
- Protections for over-voltage and over-current.
1.2 Applications
The DM320T stepper drive is designed for 2-phase (1.8°) or 4-phase (0.9°) NEMA11, 14, 16, and 17 hybrid stepper motors. It is suitable for various industries including CNC, medical, automation, packaging, X-Y tables, engraving machines, labeling machines, mills, plasma cutters, laser cutters, and pick and place devices. Its performance, simple design, and easy setup make it ideal for many step & direction control applications.
2. Setup and Installation
2.1 Physical Installation and Heat Dissipation
The DM320T weighs approximately 90g (3.5 oz). For optimal performance and longevity, ensure the drive's working temperature remains below 60°C (140°F).
- Mount the drive vertically to maximize the heat sink area.
- If necessary, use forced cooling methods (e.g., a fan) to maintain the operating temperature.
- Side mounting is recommended for better heat dissipation.
Mechanical Dimensions: The drive measures 86mm (length) x 79mm (width) x 27.5mm (height).
2.2 Wiring Connections
The DM320T features two connector blocks: P1 for control signals and P2 for power and motor connections. Always ensure the DM320T is powered off before connecting or disconnecting any terminal blocks to prevent damage or injury.
2.2.1 Connector P1 (Control Signals)
P1 handles the input control signals. It has optically isolated logic inputs to minimize electrical noise.
| Pin Function | Details |
|---|---|
| PUL | Pulse signal: Active on rising edge (4-5V HIGH, 0-0.5V LOW). Minimal pulse width 7.5µs. Add a current-limiting resistor for +12V (1K) or +24V (2K) logic voltage. |
| DIR | Direction signal: Low/high voltage levels determine motor rotation. Minimal setup time 5µs. Swapping coil wires (e.g., A+ and A-) also reverses direction. |
| OPTO | Opto-coupler power supply, typically +5V. Use series resistors for current-limiting with +12V or +24V. |
| ENA | Enable signal: High level (+5V NPN) enables, low level disables. By default, it is UNCONNECTED (ENABLED). |
Wiring Notes for Control Signals:
- Shielding control signal wires is recommended.
- To avoid interference, do not tie PUL/DIR control signal wires and motor wires together.
2.2.2 Connector P2 (Power and Motor)
P2 handles the power supply and motor connections.
| Pin Function | Details |
|---|---|
| GND | Power supply ground connection. |
| +Vdc | Power supply positive connection. Suggest 24VDC. |
| A+, A- | Motor Phase A connections. Connect motor A+ wire to A+ Pin; motor A- wire to A-. |
| B+, B- | Motor Phase B connections. Connect motor B+ wire to B+ Pin; motor B- wire to B-. |
Important: It is prohibited to plug or unplug connector P2 while the drive is powered ON, as high current flowing through motor coils can cause damaging back-EMF voltage surges.
2.2.3 Motor Connection Types
The DM320T can drive 2-phase and 4-phase bipolar hybrid stepper motors with 4, 6, or 8 wires.
- 4-lead Motor: Connect directly to A+, A-, B+, B-. The output current from the drive should be 1.4 times the specified phase current.
- 6-lead Motor:
- Half Coil Configuration (Higher Speed): Uses 50% of motor phase windings for lower inductance and stable torque at higher speeds. Connect the center taps (usually NC) and use the outer leads. Drive output current should be 1.4 times the specified per-phase (unipolar) current rating.
- Full Coil Configuration (Higher Torque): Uses full coil windings for higher torque at lower speeds. Run motors at 70% of their rated current to prevent overheating.
- 8-lead Motor: Offers flexibility for series or parallel connections.
- Series Connection: For higher torque at lower speeds. Has higher inductance, so performance degrades at higher speeds. Run motors at 70% of their rated current to prevent overheating.
- Parallel Connection: Offers more stable, lower torque at lower speeds, but higher torque at higher speeds due to lower inductance. Multiply phase (unipolar) current rating by 1.96, or bipolar current rating by 1.4, for peak output current.
2.3 Power Supply Selection
The DM320T operates with a 10-30VDC input. Selecting the correct supply voltage and output current is crucial for performance.
- Supply Voltage: Determines high-speed performance. Higher voltage allows higher motor speed but may increase noise and heating. For low-speed applications, lower voltage reduces noise and improves reliability. A 24VDC supply is generally recommended, allowing room for voltage fluctuations and back-EMF.
- Output Current: Determines motor torque, especially at lower speeds.
- Regulated vs. Unregulated: Unregulated power supplies are preferred due to their ability to handle current surges. If using a regulated supply, choose one designed for stepper/servo controls or "oversize" it (e.g., 4A supply for a 3A motor).
- Power Supply Sharing: Multiple DM320T drives can share a single power supply if it has sufficient capacity. Connect each drive directly to the power supply; do not daisy-chain connections.
2.4 DIP Switch Configurations
The DM320T uses a 6-bit DIP switch to set microstep resolution and motor operating current. The DIP switches are located on the top of the driver unit.

Figure: DM320T Digital Stepper Driver with integrated PK Current Table and Pulse/rev Table.
2.4.1 Microstep Resolution (SW4, SW5, SW6)
The last three DIP switches (SW4, SW5, SW6) configure the microstep resolution:
| Microstep | Steps/rev. | SW4 | SW5 | SW6 |
|---|---|---|---|---|
| 2 | 400 | ON | ON | ON |
| 4 | 800 | OFF | ON | ON |
| 8 | 1600 | ON | OFF | ON |
| 16 | 3200 | OFF | OFF | ON |
| 32 | 6400 | ON | ON | OFF |
| 64 | 12800 | OFF | ON | OFF |
| 20 | 4000 | ON | OFF | OFF |
| 40 | 8000 | OFF | OFF | OFF |
2.4.2 Dynamic Current (SW1, SW2, SW3)
The first three DIP switches (SW1, SW2, SW3) set the dynamic current. Select the setting closest to your motor's required current. Higher current provides more torque but increases motor and drive heating.
| Peak Current | RMS Current | SW1 | SW2 | SW3 |
|---|---|---|---|---|
| 0.3A | 0.21A | ON | ON | ON |
| 0.5A | 0.35A | OFF | ON | ON |
| 0.7A | 0.49A | ON | OFF | ON |
| 1.0A | 0.71A | OFF | OFF | ON |
| 1.3A | 0.92A | ON | ON | OFF |
| 1.6A | 1.13A | OFF | ON | OFF |
| 1.9A | 1.34A | ON | OFF | OFF |
| 2.2A | 1.56A | OFF | OFF | OFF |
Note: Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, especially under high-speed conditions.
2.4.3 Standstill Current
The standstill current is automatically reduced to 50% of the selected dynamic current 0.4 seconds after the last pulse.
3. Operating Instructions
3.1 Control Signal Sequence
To ensure correct operation and prevent deviations, PUL, DIR, and ENA signals must adhere to specific timing rules:
- t1 (ENA ahead of DIR): ENA must be asserted at least 5µs before DIR.
- t2 (DIR ahead of PUL): DIR must be asserted at least 5µs before the PUL effective edge.
- t3 (Pulse width): Pulse width must be not less than 7.5µs.
- t4 (Low level width): Low level width must be not less than 7.5µs.
(Note: A detailed sequence chart diagram is available in the full PDF user manual for visual reference.)
3.2 LED Light Indication
The DM320T has two LED indicators:
- GREEN LED: Power indicator. It will be continuously ON when the drive is powered.
- RED LED: Protection indicator. It will flash 1-2 times in a 3-second period when a protection function is enabled. The number of flashes indicates the type of protection (see Protection Functions section).
3.3 Automatic Motor Matching & Self Configuration
Upon power-on, the DM320T automatically configures itself with optimal settings to match the connected stepper motor for best performance. No manual action is required for this process.
4. Maintenance
The DM320T Digital Stepper Driver is designed for reliable operation with minimal maintenance. To ensure its longevity and optimal performance:
- Keep Clean: Ensure the drive is free from dust, oil fog, and corrosive gases. A clean environment prevents component degradation and ensures proper heat dissipation.
- Check Connections: Periodically inspect all wiring connections (P1 and P2) to ensure they are secure and free from corrosion. Loose connections can lead to erratic behavior or damage.
- Environmental Conditions: Operate the drive within the specified environmental conditions (temperature and humidity) to prevent premature failure.
- Heat Dissipation: Ensure that the drive's heat dissipation remains effective. Clear any obstructions around the unit that might impede airflow.
5. Troubleshooting
If your drive is not operating correctly, first determine if the problem is electrical or mechanical. Then, isolate the system component causing the issue. Document each step to assist in diagnosis or when seeking technical support.
| Symptoms | Possible Problems |
|---|---|
| Motor is not rotating | No power; Microstep resolution setting is wrong; DIP switch current setting is wrong; Fault condition exists; The drive is disabled. |
| Motor rotates in the wrong direction | Motor phases may be connected in reverse. |
| The drive in fault | DIP switch current setting is wrong; Something wrong with motor coil. |
| Erratic motor motion | Control signal is too weak; Control signal is interfered; Wrong motor connection; Something wrong with motor coil. |
| Motor stalls during acceleration | Current setting is too small, losing steps; Motor is undersized for the application; Acceleration is set too high; Power supply voltage too low. |
| Excessive motor and drive heating | Inadequate heat sinking / cooling; Automatic current reduction function not being utilized; Current is set too high. |
5.1 Protection Functions
The drive incorporates built-in protection features. When active, the motor shaft will be free, and the red LED will blink. Reset the drive by repowering it after resolving the issue.
| Priority | Time(s) of Blink | Description |
|---|---|---|
| 1st | 1 | Over-current protection activated when peak current exceeds the limit. |
| 2nd | 2 | Over-voltage protection activated when drive working voltage is greater than 34VDC. |
| 3rd | 3 | Reserved. |
6. Specifications
6.1 Electrical Specifications
| Parameters | Min | Typical | Max | Unit |
|---|---|---|---|---|
| Output Current | 0.3 | - | 2.2 (1.6 RMS) | A |
| Supply Voltage | 10 | 24 | 30 | VDC |
| Logic signal current | 7 | 10 | 16 | mA |
| Pulse input frequency | 0 | - | 60 | kHz |
| Minimal pulse width | 7.5 | - | - | µs |
| Minimal direction setup | 7.5 | - | - | µs |
| Isolation resistance | 100 | - | - | MΩ |
6.2 Environmental Specifications
| Parameter | Value |
|---|---|
| Cooling | Natural Cooling or Forced cooling |
| Environment | Avoid dust, oil fog and corrosive gases |
| Ambient Temperature | 0°C - 65°C (32°F - 149°F) |
| Humidity | 40%RH - 90%RH |
| Operating Temperature | 0°C - 50°C (32°F - 122°F) |
| Vibration | 10-50Hz / 0.15mm |
| Storage Temperature | -20°C - 65°C (-4°F - 149°F) |
| Weight | Approx. 90g (3.5 oz) |
6.3 Mechanical Specifications
- Length: 86 mm
- Width: 79 mm
- Height: 27.5 mm
- Mounting Hole Spacing: 79 mm (length), 20 mm (width)
7. User Tips
- The DM320T is designed to be very simple to use, making it accessible even for those less technically minded.
- The product is well-made and robust, ensuring reliable operation.
8. Support and Contact Information
For technical support or inquiries, please use the following contact details:
- Address: 15-4, #799 Hushan Road, Jiangning, Nanjing, China
- Tel: 0086-2587156578
- Web: www.omc-stepperonline.com
- Sales: sales@stepperonline.com
- Support: technical@stepperonline.com
A detailed user manual in PDF format is also available for download from the seller's website or via this direct link: DM320T User Manual (PDF).