diymore MP1584EN

Contents

Mini MP1584EN DC-DC Buck Converter Adjustable Power Supply Module

Model: MP1584EN

Introduction

This manual provides essential information for the safe and effective use of your diymore Mini MP1584EN DC-DC Buck Converter Adjustable Power Supply Module. This compact module is designed to step down a higher input voltage to a lower, adjustable output voltage, making it suitable for a wide range of electronic projects and power supply applications.

Safety Information and Warnings

  • Polarity: Do not reverse the positive and negative terminals during connection to avoid any possible damage to the module or connected devices.
  • Input Voltage: The input voltage should not exceed 28V to prevent damage to the module.
  • Load Conditions: Do not operate the module without a load or with a very light load (less than 10% of its output power capacity).
  • Short Circuit: Avoid creating a short circuit on the output, as this will burn out the board.
  • Voltage Adjustment: When adjusting the output voltage, ensure the output is stable before connecting any sensitive devices to prevent potential damage.

Package Contents

  • 1 x Mini MP1584EN DC to DC Buck Converter Board

Setup Instructions

1. Identifying Terminals

The module features clearly marked input and output terminals. The input terminals are labeled 'IN+' and 'IN-', and the output terminals are labeled 'OUT+' and 'OUT-'.

Bottom view of the MP1584EN module showing IN+ IN- and OUT+ OUT- terminals.
Figure 1: Bottom view of the module indicating input and output terminals.

2. Wiring the Module

Connect your DC power source to the 'IN+' (positive) and 'IN-' (negative) terminals. Connect your load (the device you want to power) to the 'OUT+' (positive) and 'OUT-' (negative) terminals. Ensure all connections are secure and observe correct polarity.

Wiring diagram for the MP1584EN module showing input and output connections and the adjustable potentiometer.
Figure 2: Wiring diagram and potentiometer location.

3. Adjusting Output Voltage

The module features an adjustable potentiometer (a small screw-like component) for setting the output voltage. To adjust:

  1. Connect a multimeter to the output terminals ('OUT+' and 'OUT-') to monitor the voltage.
  2. Apply power to the input terminals.
  3. Using a small screwdriver, carefully turn the potentiometer. Turning clockwise will step down the voltage, and turning counter-clockwise will step up the voltage. Make minute adjustments to achieve the precise desired voltage.
  4. Once the desired output voltage is stable, you can connect your load.

Operating Instructions

This DC-DC buck converter is designed for various applications requiring a stable, lower voltage from a higher input. Common uses include:

  • DIY mobile power supplies
  • Monitor power supplies
  • Powering buggies and remote-controlled vehicles
  • Camera power supplies
  • Car power applications
  • Communications equipment power supply

Always ensure the module is operating within its specified input and output voltage/current ranges to prevent damage.

Specifications

Table of specifications for the MP1584EN module including input/output voltage, current, efficiency, ripple, frequency, temperature, size, and application.
Figure 3: Detailed product specifications.
MP1584EN Module Specifications
ParameterValue
Input voltage4.5 V to 28 V
Output voltage0.8 V to 20 V
Output current3 A (maximum)
Conversion efficiency92% (maximum)
Output rippleless than 30 mV
Switching frequency1.5 MHz (highest), typically 1 MHz
Operating temperature-45 °C to 85 °C
Size22 mm x 17 mm x 4 mm
Image showing the dimensions of the MP1584EN module as 22mm by 17mm.
Figure 4: Module dimensions (22mm x 17mm).

Troubleshooting

  • No Output Voltage: Check input power supply, ensure correct polarity, and verify connections.
  • Incorrect Output Voltage: Use a multimeter to measure the output and adjust the potentiometer carefully.
  • Module Overheating: If the module becomes excessively hot, especially at higher currents (e.g., 1.3A or more), consider adding a heatsink to the main chip or inductor to improve thermal dissipation.
  • Module Failure: If the module fails immediately upon connection, re-check for reversed polarity, output short circuits, or exceeding the maximum input voltage.

Maintenance

The MP1584EN module is a robust electronic component requiring minimal maintenance. To ensure its longevity:

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to moisture or extreme temperatures outside its operating range.
  • Handle with care to prevent physical damage to components or solder joints.

User Tips

  • For applications drawing higher currents (e.g., 1.3A or more), it is advisable to consider active or passive cooling for the module, particularly the inductor (coil) and the main IC, to maintain optimal performance and prevent overheating.
  • When integrating into projects like portable loudspeakers, ensure stable input power and proper voltage adjustment for the audio components.

Additional Resources

A detailed user manual in PDF format is available for further reference. You can access it at: MP1584EN User Manual (PDF)

Warranty and Support

For any issues, technical support, or warranty claims, please contact the seller or manufacturer directly. Ensure you have your purchase details readily available.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.