diymore AC-DC 5V 700mA 3.5W Power Supply Module

Contents

AC-DC 5V 700mA 3.5W Power Supply Buck Converter Step Down Module User Manual

Model: AC-DC 5V 700mA 3.5W Power Supply Module (XL-007)

Brand: diymore

1. Introduction

This document provides instructions for the AC-DC 5V 700mA 3.5W Power Supply Buck Converter Step Down Module. This compact module is designed to convert AC 85-265V or DC 100-370V input into a stable DC 5V output, making it suitable for various electronic projects, including those involving Arduino. It features multiple built-in protections to ensure safe and reliable operation.

2. Safety Information

  • Always ensure the power source is disconnected before making any connections to the module.
  • This module operates with high voltage AC input. Exercise extreme caution to avoid electric shock.
  • Ensure proper insulation and avoid contact with live parts during operation.
  • Do not exceed the specified input voltage or output current limits.
  • Keep the module away from moisture, dust, and extreme temperatures.
  • If you are unsure about any aspect of installation or operation, consult a qualified electrician or electronics professional.

3. Product Overview

The module is a compact PCB with integrated components for power conversion. It includes capacitors, a transformer, and various ICs for voltage regulation and protection.

Top view of the AC-DC 5V 700mA 3.5W Power Supply Buck Converter Step Down Module, showing capacitors and transformer.

Figure 1: Top view of the module, showing capacitors and transformer.

Side view of the module, highlighting its compact size and component arrangement.

Figure 2: Side view of the module, highlighting its compact size.

Bottom view of the module, displaying the PCB traces, solder points, and some surface-mount components.

Figure 3: Bottom view of the module, showing PCB traces and components.

4. Specifications

ParameterValue
Input Voltage (AC)AC 85 ~ 265 V (50/60 Hz)
Input Voltage (DC)DC 100 ~ 370 V
Input Current (AC110V)0.0273A
Input Current (AC220V)0.014A
Input Inrush Current20A
Output VoltageDC 5V (+ / - 0.2 V)
Output Current (Max)700 mA
Output Current (Peak)800 mA
Output Power3.5 W (0-4W DC current)
Output Voltage Range4.8 ~ 5.2 V
Ripple Wave60mV
Output Efficiency80%
Switch Machine OvershootMAX 10%
Output Voltage Rise TimeMAX 100MS
Operating Temperature-20 ~ 60°C
Relative Humidity40-90%RH
Dimensions3 x 2 x 1.8 cm

5. Setup and Installation

Refer to the module's PCB markings for correct input and output connections. Always ensure power is disconnected before wiring.

5.1. Pinout

The module typically has clearly labeled pins for input and output. Based on common configurations and visual inspection of the module (Figure 1, Figure 3), the connections are as follows:

  • AC IN: Connect your AC power source (85-265V) to these pins. Polarity is generally not critical for AC input, but ensure secure connections.
  • DC OUT: These pins provide the regulated DC 5V output. Observe polarity: '+' for positive, '-' for negative (GND).
Angled view of the module, showing the input and output pins.

Figure 4: Angled view showing input and output pins.

5.2. Wiring Instructions

  1. Input Connection: Connect the AC mains (Live and Neutral) or DC power source (Positive and Negative) to the designated 'AC IN' terminals on the module. Ensure connections are firm and insulated.
  2. Output Connection: Connect your load (e.g., Arduino, 5V device) to the 'DC OUT' terminals. Connect the positive (+) terminal of the module to the positive input of your device, and the negative (-) terminal of the module to the negative (GND) input of your device.
  3. Verification: Double-check all connections for correctness and polarity before applying power.

6. Operating Instructions

Once properly wired, apply power to the input terminals. The module will automatically regulate the voltage to a stable DC 5V output. No further configuration is typically required for basic operation.

  • Ensure the load connected to the output does not exceed 700mA continuous current (800mA peak).
  • Monitor the module for any signs of overheating or unusual behavior during initial operation.

7. Maintenance

This module is designed for low maintenance. Keep it clean and free from dust and debris. Periodically check connections for tightness and signs of corrosion. Do not attempt to repair the module if it malfunctions; replacement is recommended.

8. Troubleshooting

The module incorporates several protection features. If the module stops functioning, consider the following:

  • No Output Voltage: Check input power supply. Verify all connections are correct and secure.
  • Output Over Voltage (4.8-5.2V): The module will lock and require a restart (power cycle) to recover.
  • Output Over Power Protection: If the load draws too much power, the module will lock. Remove the excessive load and restart the module.
  • Short-Circuit Protection: If a short circuit occurs at the output, the module will automatically recover once the short is removed.
  • Temperature Protection: If the module overheats, it will lock. Allow it to cool down and then restart. Ensure adequate ventilation for the module.
  • Overcurrent Protection: If the output current exceeds the limit, the module will lock. Reduce the load and restart.

9. User Tips

  • Due to its very small and compact size (3 x 2 x 1.8 cm), this module is ideal for projects where space is limited.
  • Consider using appropriate enclosures to protect the module from environmental factors and accidental contact, especially given its high voltage input.

10. Warranty and Support

For detailed technical support or warranty information, please refer to the official product documentation. A user manual in PDF format may be available for download from the manufacturer or seller's website. For example, a user manual (PDF) can be found at this link.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.