Lizard EK Series

Contents

Lizard Fishing EK Series Jigging/Trolling Reel User Manual

1. Introduction

Thank you for choosing the Lizard Fishing EK Series Jigging/Trolling Reel. This manual provides essential information for the proper setup, operation, and maintenance of your new fishing reel. Please read it thoroughly before use to ensure optimal performance and longevity of your product.

Product Features:

  • CNC Machined Aluminum Body
  • High Drag Power (up to 26kg)
  • Deep Spool Design
  • Ambidextrous Hand Direction
  • Designed for Sea Saltwater Trolling and Jigging

2. Package Contents

Please check the package to ensure all components are present:

  • Lizard Fishing EK Series Reel Body
  • Reel Handle Assembly
  • Reel Mounting Clamp and Screws
  • Neoprene Reel Cover (may be included)
Lizard Fishing Reel with mounting clamp and screws

Figure 2.1: Reel components including mounting clamp and screws.

3. Setup Instructions

3.1. Handle Installation

  1. Locate the reel body and the handle assembly.
  2. Align the handle shaft with the corresponding slot on the reel body.
  3. Insert the handle shaft and secure it by tightening the handle screw or cap (if applicable). Ensure it is firmly attached but do not overtighten.
Assembled Lizard Fishing Reel with handle

Figure 3.1: Fully assembled reel with handle.

3.2. Mounting the Reel to a Fishing Rod

  1. Place the reel foot into the reel seat of your fishing rod.
  2. Position the reel mounting clamp around the rod and secure it to the reel foot using the provided screws.
  3. Tighten the screws evenly until the reel is firmly attached to the rod. Do not overtighten, as this may damage the rod or reel.

3.3. Spooling Fishing Line

  1. Attach the end of your fishing line to the reel spool. You may use an arbor knot or a simple overhand knot with tape for security.
  2. Ensure the line is spooled under light tension to prevent line memory and ensure even distribution.
  3. Fill the spool to approximately 1/8 inch (3mm) from the rim to prevent line overflow and tangles during casting.

4. Operating Instructions

4.1. Drag System Adjustment

The drag system controls the amount of resistance the line experiences when a fish pulls on it. To adjust:

  • Increase Drag: Turn the drag star/lever clockwise.
  • Decrease Drag: Turn the drag star/lever counter-clockwise.

Always set your drag before fishing. A good starting point is to set the drag to about 25-30% of your line's breaking strength.

4.2. Casting

⚠️ WARNING! ⚠️

Before casting, please be aware of your surroundings and ensure safety. Check for overhead obstructions, people, and other hazards.

For trolling reels, casting is typically done by releasing the spool (free spool mode) and allowing the bait to drop or be carried by the boat's movement. For jigging, release the spool to drop the jig to the desired depth.

4.3. Retrieving

To retrieve your line, simply turn the handle clockwise. Ensure the line is winding evenly onto the spool. If using a level wind system (if present), ensure it is functioning correctly.

5. Maintenance

Proper maintenance will extend the life and performance of your reel, especially when used in saltwater environments.

5.1. After Each Use

  • Rinse: Lightly rinse the reel with fresh water to remove salt, sand, and debris. Do not use high-pressure water, as it can force water into the reel's internal components.
  • Dry: Wipe the reel dry with a soft cloth. Allow it to air dry completely before storage.
  • Loosen Drag: Always back off the drag setting to its lightest position before storing to prevent compression of the drag washers.

5.2. Periodic Maintenance

  • Lubrication: Apply a small amount of reel oil to moving parts such as the handle knob, bail arm pivots, and any visible bearings. Use reel grease on gears if you disassemble the reel (recommended for experienced users only).
  • Inspection: Periodically inspect the reel for any signs of wear, corrosion, or damage. Check screws for tightness.

5.3. Storage

Store your reel in a cool, dry place away from direct sunlight and extreme temperatures. Using the provided neoprene reel cover (if included) can protect it from dust and minor impacts.

6. Troubleshooting

If you encounter issues with your reel, try the following common solutions:

  • Stiff Handle/Rough Operation: Clean the reel thoroughly and apply appropriate lubrication. Check for any debris obstructing movement.
  • Drag Not Smooth: Ensure the drag washers are clean and free of debris. If heavily used, drag washers may need replacement.
  • Line Tangles/Poor Casting: Check for proper line spooling (not overfilled, even tension). Inspect the line for damage or twists.

For persistent issues, please refer to the Warranty/Support section.

7. Specifications

Specifications table for EK02, EK03, EK04 models

Figure 7.1: Model-specific performance specifications.

Lizard Fishing EK Series Reel Specifications
FeatureDescription
BrandLizard
Model NumberEK Series (EK02, EK03, EK04)
MaterialAluminum
Hand DirectionAmbidextrous (Left/Right Hand options available)
Fishing Reels TypeTrolling Reel
Fishing MethodTrolling
PositionOcean Boat Fishing
Baits TypeFake Bait
Number of Bearings7BB+1
Speed Ratio4.5:1 (Single Speed)
Weight (approx.)EK02: 550g, EK03: 577g, EK04: 571g

8. User Tips

  • Robust Construction: Users frequently praise the reel's robust and solid aluminum construction, indicating good durability for demanding fishing conditions.
  • Smooth Operation: The reel's connector and overall operation are noted for being smooth, contributing to a better fishing experience.
  • High-Quality Finish: The high-quality finish suggests attention to detail and aesthetics.
  • Check Spool Capacity: Always verify the line capacity for your specific model (EK02, EK03, EK04) to ensure you spool the correct amount and type of line.

9. Warranty and Support

For any warranty claims, technical support, or inquiries regarding your Lizard Fishing EK Series Reel, please contact your original point of purchase or the official Lizard Fishing customer service. Please have your purchase details and model number ready when contacting support.

© 2024 Lizard Fishing. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.