YurKuong YK-24V02CR01+BK-ab

Contents

YurKuong DC24V 2CH Micro Relay Remote Switch User Manual

Model: YK-24V02CR01+BK-ab

Introduction

This manual provides comprehensive instructions for the YurKuong DC24V 2CH Micro Relay Remote Switch, model YK-24V02CR01+BK-ab. This device is a 2-channel wireless relay receiver designed for remote ON/OFF control of DC24V circuits. It supports both Momentary and Latched operating modes, allowing for flexible application in various control scenarios.

Please read this manual carefully before installation and operation to ensure proper use and to prevent damage to the device or connected equipment.

Product Overview

The YurKuong DC24V 2CH Micro Relay Remote Switch consists of a compact receiver module and a 2-button remote control. The receiver features a single relay with two channels (2CH) for simultaneous ON/OFF control. Its small size makes it suitable for integration into various projects requiring wireless switching capabilities.

YurKuong DC24V 2CH Micro Relay Remote Switch with remote control and receiver module.
Figure 1: Main components of the YurKuong DC24V 2CH Micro Relay Remote Switch.

Specifications

ParameterValue
Working VoltageDC24V
Channel2CH (2 channels ON/OFF simultaneously, one relay with 2CH output)
Max Load2A (recommended less than 1A for optimal performance)
Standby Current7mA
Working Current28mA
Working Frequency433.92MHZ
Dimensions (Receiver)20mm x 18mm x 7mm
Working ModeMomentary or Latched (adjustable by soldering)
Output Type0V Switching Value (Relay NO COM NC)
MaterialAluminium alloy
CertificationCCC
Remote Distance10-100m

Setup Instructions

1. Wiring the Receiver Module

The receiver module requires a DC24V power supply and provides Normally Open (NO), Normally Closed (NC), and Common (COM) contacts for switching your load. Refer to the pinout diagram below for correct connections.

Bottom view of the receiver module showing V+, V-, COM1, NC1, NO1, COM2, NC2, NO2 pinouts.
Figure 2: Receiver Module Pinout Diagram.
  • V+: Input +VCC (DC24V positive)
  • V-: Input -GND (DC24V negative)
  • COM1/2: Common terminal for the relay contacts.
  • NC1/2: Normally Closed terminal. This contact is closed when the relay is de-energized and opens when energized.
  • NO1/2: Normally Open terminal. This contact is open when the relay is de-energized and closes when energized.

Caution: The maximum load is 2A. For optimal performance and longevity, it is recommended to keep the load current below 1A. Ensure correct polarity when connecting the DC24V power supply.

2. Selecting the Working Mode (Momentary or Latched)

The receiver module supports two working modes: Momentary and Latched. This mode is adjusted by soldering specific points on the receiver board. Refer to the diagram below to identify the adjustment points.

Close-up of the receiver board showing solder points for Momentary/Latched adjustment and the Learning Dot.
Figure 3: Receiver Board with Mode Adjustment and Learning Dot.
  • Momentary Mode: The relay remains ON only while the remote button is pressed. Release the button, and the relay turns OFF. To set this mode, solder the designated points for "Momentary" as indicated on the board (often labeled 'S2' or similar, near '001' in the image).
  • Latched Mode: Pressing a remote button turns the relay ON, and it stays ON until another designated button is pressed to turn it OFF. To set this mode, solder the designated points for "Latched" as indicated on the board (often labeled 'SET' or similar, near the antenna in the image).

Warning: Soldering requires appropriate tools and skills. Incorrect soldering can damage the module. If unsure, seek professional assistance.

3. Pairing the Remote Control (Learning Procedure)

After setting the desired working mode, you need to pair the remote control with the receiver module. The receiver has a "Learning Dot" (often a small button or solder pad labeled 'SET' or similar) used for this process.

  1. Ensure the receiver module is powered with DC24V.
  2. Press and hold the "Learning Dot" on the receiver module for approximately 3 seconds. The indicator LED on the receiver should light up, indicating it's in learning mode.
  3. While the LED is lit, press the button on your remote control that you wish to pair (e.g., button 'A' for ON in Latched mode, or any button for Momentary mode).
  4. The receiver's LED should flash a few times and then turn off, indicating successful pairing.
  5. Test the remote control to confirm functionality.
  6. To clear all paired remotes, press and hold the "Learning Dot" for approximately 8 seconds until the LED flashes rapidly and then turns off. This will erase all stored remote codes.

Note: If you are having trouble pairing, ensure the remote control has a working battery and is within range of the receiver.

Operating Instructions

Momentary Mode Operation

In Momentary mode, the relay activates only while the remote button is pressed. Both channels (2CH) will turn ON simultaneously when the button is pressed, and turn OFF when released.

  • To turn ON: Press and hold the paired button on the remote control.
  • To turn OFF: Release the paired button on the remote control.

Latched Mode Operation

In Latched mode, the relay toggles its state with each press of a paired button. If using a 2-button remote (A and B), typically one button is for ON and the other for OFF.

  • To turn ON: Press button 'A' on the remote control. Both channels (2CH) will turn ON simultaneously and remain ON.
  • To turn OFF: Press button 'B' on the remote control. Both channels (2CH) will turn OFF simultaneously and remain OFF.

Maintenance

  • Keep the receiver module and remote control dry. Moisture can damage electronic components.
  • Avoid exposing the devices to extreme temperatures.
  • Clean the devices with a soft, dry cloth. Do not use harsh chemicals or solvents.
  • Replace the remote control battery when its range decreases or it stops responding.

Troubleshooting

ProblemPossible CauseSolution
Receiver does not respond to remote control.
  • Remote not paired.
  • Incorrect working mode set.
  • Remote battery is low or dead.
  • Remote is out of range.
  • Interference from other RF devices.
  • Perform the pairing procedure (see Setup section).
  • Verify the working mode (Momentary/Latched) is correctly set via soldering.
  • Replace the remote control battery.
  • Move closer to the receiver.
  • Relocate the receiver or remote to minimize interference.
Relay activates intermittently or unexpectedly.
  • Weak signal or interference.
  • Loose wiring connections.
  • Check for sources of RF interference.
  • Ensure all wiring connections are secure.
Receiver LED does not light up during pairing.
  • No power to the receiver.
  • Learning Dot not pressed correctly.
  • Verify DC24V power supply is connected and functional.
  • Ensure the Learning Dot is pressed firmly for the required duration.

User Tips

  • Clear Pairing Instructions: Some users have found the pairing process unclear. Always ensure you press and hold the "Learning Dot" until the LED indicates learning mode, then press the remote button. If it doesn't work, try clearing all paired remotes first.
  • Check Working Mode: Double-check that the desired working mode (Momentary or Latched) is correctly set via soldering before attempting to pair the remote.
  • Load Current: While rated for 2A, consider keeping the load below 1A for extended reliability, especially in continuous operation.

Warranty and Support

This YurKuong product comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For further assistance or detailed technical information, you may refer to the official user manual PDF available at: YurKuong DC24V 2CH Micro Relay Remote Switch User Manual (PDF).

For support inquiries, please contact YurKuong Official Store directly through the platform where the product was purchased.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.