Introduction
This manual provides instructions for the installation and safe use of your Biurlink Mini ISO Radio Adapter Cable. This cable is designed to extend or distribute the 20-pin mini ISO block in compatible car audio systems, allowing for the connection of additional accessories such as CD changers, amplifiers, or external audio sources.
Specifications
| Condition | 100% Brand New |
| Material | Plastic & Rubber |
| Connector Type | ISO 20Pin Female to Male |
| Cable Length | 23 cm |
| Item Weight | 0.03 kg |
| Voltage | 12 V |
| Special Features | Car media in harness cable |
| Item Type | Cables, Adapters & Sockets |
| Origin | Mainland China |
Compatibility
This adapter cable is compatible with various car models and radio systems. It is designed for vehicles where the 20-pin mini ISO block is not divisible and requires an extension or distribution for connecting additional accessories.
Compatible Car Models (1997-2005):
- Volkswagen (1997-2003): Beetle, Bora, Caddy, Caravelle, Corrado, FOX, Golf 3, Golf 4, Jetta, LT, Lupo, Multivan, Passat, Polo, Sharan, Touran, Touareg, Transporter T4, T5, T6, Vento
- Audi (1997-2005): A2, A3, S3, A4, S4, A6, S6, A8, S8, Allroad, Q5, Q7, TT
- Seat (1997-2004): Alhambra, Arosa, Cordoba, Ibiza, Inca, Leon, Toledo, Vario
- Skoda (1997-2004): Fabia, Favorit, Felicia, Octavia
Compatible Radio Models:
- General: Blaupunkt, Becker, Grundig, VDO
- Volkswagen: VW MFD (in Golf IV, Bora, Sharan, T4, Passat, Jetta, Skoda, Seat, Ford), Alpha (New Beetle), Beta 5, Beta T4, Gamma, Gamma 5, Gamma (New Beetle), Monsoon, Rhapsody, Premium 4 Clarion, Premium 5 Delco, RNS-MCD, RNS-MFD, VW Z6Z9, VW Z9Z7
- Audi: Audi navigation system plus (RNS-D) (in A2, A3, A4, A6, A8), Concert I, Concert II, Chorus II, Symphony I, Symphony II, Navigation MFD Plus
- Seat: Aura, Beta, Elba, Highline, Lena, Liceo, Alana, Scala, Soundsystem 2, MFD, MCD (Dynamic Navi), Navi RNS, Ibiza, GPI (SS2), SEZ2Z6
- Skoda: MS 501, MS 502, Navi DX, SatCompass, Symphony, RNS, MCD, MFD
Please verify your vehicle and radio model for compatibility before installation.
Package Contents
- 1 x Biurlink Mini ISO Radio Adapter Cable
Setup Instructions
Follow these steps to install the adapter cable:
- Carefully remove your car stereo unit from its dashboard slot. Refer to your car's specific manual for stereo removal procedures.
- Locate the 20-pin mini ISO block on the back of your car stereo.
- Plug the female end of the Biurlink Mini ISO Radio Adapter Cable into the corresponding port on your car stereo.
- Connect your desired accessory (e.g., CD changer, amplifier, external audio source) to the appropriate mini ISO connectors (blue, green, or yellow) on the adapter cable.
- Carefully re-install your car stereo unit into the dashboard.
- Turn on your car stereo and navigate to the settings menu to configure the newly connected accessory.
Operating Instructions
Once the Biurlink Mini ISO Radio Adapter Cable is correctly installed and your accessory is connected, operate your car stereo as usual. The adapter acts as a pass-through or splitter for the mini ISO block, allowing your car stereo to recognize and control the connected device. Refer to your car stereo's user manual for specific instructions on selecting input sources or controlling external devices.
Maintenance
The Biurlink Mini ISO Radio Adapter Cable requires minimal maintenance. Keep the cable and connectors clean and free from dust and debris. Avoid bending or twisting the cable excessively, as this can damage the internal wiring. Ensure connections remain secure to prevent signal loss or intermittent operation.
Troubleshooting
- No signal from connected device: Ensure all connections are secure and fully seated. Verify that your car stereo is set to the correct input source for the connected accessory. Check the accessory itself for proper function.
- Accessory not recognized: Double-check the compatibility of the adapter with your specific car stereo and the accessory you are trying to connect. Ensure the car stereo's firmware is up to date if applicable.
- Intermittent connection: Inspect the cable for any visible damage. Ensure the connectors are clean and free from corrosion.
Safety Precautions
- WARNING: For safety, use only with an approved car stereo power supply.
- Do not attempt to install or handle the cable while the vehicle's ignition is on or the car stereo is powered. Disconnect the car battery before performing any electrical work.
- Do not use the cable or connected devices in a way that distracts you while driving. Always prioritize road safety.
- Keep the adapter cable and any connected electronic devices away from water, rain, or other liquids to prevent damage and electrical hazards.
- Avoid exposing the cable to extreme temperatures or direct sunlight for prolonged periods.
User Tips
- Verify Compatibility: Before purchasing or installing, always confirm that this adapter cable is compatible with your specific car model and radio unit to ensure proper functionality.
- Quality and Workmanship: Users have noted the good quality and workmanship of the product, indicating reliability for its intended purpose.
- Functionality: The adapter is reported to effectively perform its job of extending or distributing the mini ISO connection.
Warranty and Support
For any questions, technical support, or warranty inquiries regarding your Biurlink Mini ISO Radio Adapter Cable, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
A PDF version of the user manual may also be available for download from the product page or seller's website.