E-SIMPO 80mA 5mm Piranha LED

Contents

User Manual: 5mm Piranha 4-chip LED

Model: 80mA 5mm Piranha LED

Brand: E-SIMPO

1. Introduction

This manual provides comprehensive instructions for the E-SIMPO 80mA 5mm Piranha 4-chip LED. These high-brightness LEDs are available in various colors including Red, Green, Blue, Yellow, Warm White, and Cold White, making them suitable for a wide range of lighting applications, particularly in automotive and general LED lighting projects. Please read this manual thoroughly before installation and operation to ensure proper use and longevity of the product.

Two E-SIMPO 5mm Piranha 4-chip LEDs, showing their square base and domed lens.
Figure 1: E-SIMPO 5mm Piranha 4-chip LEDs.

2. Features

  • High intensity Polygonal LED lamp
  • 5mm round shape
  • UV resistant epoxy
  • 4-chip design for enhanced brightness
  • Available in multiple colors: Red, Yellow, Blue, Green, Cold White, Warm White

3. Applications

  • General LED Lighting
  • Automotive Lighting applications (e.g., Eagle-eye lights)
  • Indicator lights
  • Custom electronic projects

4. Technical Specifications

4.1. Absolute Maximum Ratings (Ta=25°C)

Parameter Symbol Max Value Unit
Power Dissipation Ps 300 mW
Peak Forward Current Ip 160 mA
Continuous Forward Current If 80 mA
Reverse Voltage Vs 5 V
Operating Temperature Range Topr -30 to +80 °C
Storage Temperature Range Tstg -40 to +100 °C
Lead Soldering Temperature (within 5 seconds at 4mm from package bottom) Tsol 260 °C

4.2. Electrical Optical Characteristics by Color (Ta=25°C, @IF=80mA)

Color Brightness (mcd) Wavelength (nm) / Color Temperature (K) Forward Voltage (V) Viewing Angle (°) Chip Size
Red 6000-8000 620-630 2.0-2.4 90 14Mil
Yellow 6000-8000 588-595 2.0-2.4 90 14Mil
Blue 2000-3000 465-470 3.0-3.6 90 9*13Mil
Green 8000-10000 515-525 3.0-3.6 90 9*13Mil
Cold White 8000-10000 6000-7000 K 3.0-3.6 90 10*16Mil
Warm White 8000-10000 2800-3200 K 3.0-3.6 90 10*16Mil

4.3. Physical Dimensions and Pinout

Technical drawing showing dimensions of the 5mm Piranha LED and its four-pin wiring diagram. Dimensions include 7.62x7.62mm square base, 5.08mm width, 4.5mm height, and 0.75mm pin width.
Figure 2: Piranha LED dimensions and wiring diagram. The diagram shows two anodes (A) and two cathodes (-), with internal diodes connecting them.

The Piranha LED features a square base with four pins for connection. Refer to Figure 2 for detailed dimensions and the pin configuration. The diagram indicates two anode (positive) pins and two cathode (negative) pins, internally connected.

Close-up top view of a Piranha LED, showing the four individual LED chips visible through the clear epoxy lens.
Figure 3: Top view of the Piranha LED, highlighting the 4-chip design.
Close-up side view of a Piranha LED, showing the clear domed lens and the two pins extending from the side.
Figure 4: Side view of the Piranha LED.
Close-up bottom view of a Piranha LED, clearly showing the four metal pins for electrical connection.
Figure 5: Bottom view of the Piranha LED, showing the pins.

5. Installation and Wiring

These LEDs are designed for through-hole mounting. Proper polarity must be observed during installation. Refer to Figure 2 for the pinout diagram. The two pins marked 'A' are anodes (positive), and the two pins marked '-' are cathodes (negative). Ensure correct voltage and current are supplied to prevent damage.

5.1. Handling Precautions

  • Static Electricity: LEDs are sensitive to static electricity. It is recommended to use a wrist band or anti-electrostatic gloves when handling the LEDs. All devices, equipment, and machinery must be properly grounded.
  • Inspection: When inspecting final products with mounted LEDs, static-damaged LEDs can be identified by a light emission test at a lower current (below 1mA is recommended).
  • Damaged LEDs: Damaged LEDs may exhibit unusual characteristics such as remarkably increased leak current, lower starting forward voltage, or failure to light up at low current.

6. Operation

To operate the LED, apply the specified forward voltage (VF) and ensure the continuous forward current (If) does not exceed 80mA. Exceeding these limits can significantly reduce the lifespan of the LED or cause immediate failure. A current-limiting resistor is typically required in series with the LED when connecting to a voltage source higher than the LED's forward voltage.

The LEDs are designed for a duty ratio maximum of 1/10 and a pulse width maximum of 0.1ms for pulsed operation.

7. Care and Maintenance

  • Keep LEDs clean and free from dust or debris, which can affect light output.
  • Avoid exposing LEDs to harsh chemicals or solvents.
  • Ensure proper heat dissipation, especially when operating at higher currents, to maintain optimal performance and lifespan.
  • Store unused LEDs in a dry, anti-static environment within the specified storage temperature range (-40°C to +100°C).

8. Troubleshooting

Problem Possible Cause Solution
LED does not light up Incorrect polarity; insufficient voltage/current; damaged LED; open circuit. Check wiring for correct polarity (Anode to positive, Cathode to negative). Verify power supply voltage and ensure adequate current with a current-limiting resistor. Test the LED with a known good power source. Inspect for physical damage.
LED is dim or flickers Insufficient current; unstable power supply; damaged LED (static damage). Ensure the current-limiting resistor is correctly sized for the desired brightness. Use a stable power supply. If static damage is suspected (increased leak current, lower starting VF), replace the LED.
LED fails prematurely Overcurrent; overvoltage; excessive heat; static discharge. Always use a current-limiting resistor. Ensure the power supply matches the LED's voltage requirements. Provide adequate heat dissipation. Follow anti-static handling procedures.

9. User Tips

  • When designing circuits, always include a current-limiting resistor to protect the LED from overcurrent.
  • For optimal brightness and lifespan, operate the LEDs within their recommended continuous forward current (80mA).
  • Consider using a heatsink for applications where multiple LEDs are used or if they are enclosed, to prevent overheating.
  • Always double-check polarity before applying power to avoid damaging the LED.

10. Frequently Asked Questions

Q: What is the typical forward voltage for these LEDs?
A: The typical forward voltage (VF) varies by color. For Red and Yellow, it's typically 2.0-2.4V. For Blue, Green, Cold White, and Warm White, it's typically 3.0-3.6V.
Q: How many chips are inside each Piranha LED?
A: Each Piranha LED features a 4-chip design, contributing to its high brightness output.
Q: Can these LEDs be used in outdoor applications?
A: Yes, they feature UV resistant epoxy, making them suitable for applications where UV exposure is a concern. However, ensure proper waterproofing and environmental protection for the entire assembly if used outdoors.
Q: What is the maximum continuous current?
A: The maximum continuous forward current is 80mA. It is recommended to operate at or below this value for optimal performance and longevity.

11. Additional Resources

For more detailed technical information, including performance graphs and comprehensive endurance test data, please refer to the official user manual PDF:

View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.