Biurlink IP-BUS Aux Cable

Contents

Biurlink Car Radio Audio Aux Cable MP3 Input Adapter

Model: IP-BUS Aux Cable

Introduction

This manual provides instructions for the installation, operation, and maintenance of your Biurlink Car Radio Audio Aux Cable. This adapter allows you to connect external audio devices, such as smartphones, tablets, or MP3 players, to compatible Pioneer car stereos equipped with an IP-BUS port, enabling high-quality audio streaming.

Package Contents

Please check the package for the following items:

  • 1 x AUX Cable (1.5m)
  • 1 x User Manual

Specifications

FeatureDescription
Condition100% Brand New
Cable Length1.5 meters
Socket Type3.5mm Stereo Jack
Connector TypePioneer IP-BUS (CD Changer Port)
Interface3.5mm Audio Input
MaterialPlastic
Item Weight0.04 kg
Voltage12 V (Car System)
Out Power6W
Cable thickness measurement showing 4.34mm
Figure 1: Cable thickness measurement (4.34mm)

Compatibility

This AUX cable is designed for Pioneer car radios with a CD changer port, commonly known as IP-Bus. Your car stereo must have an AUX function that can be selected as an input source (e.g., AUX / EXT / CD-CH).

Compatible Pioneer Models (P-series):

  • DEH-P2500 R, DEH-P2600 R, DEH-P3500 MP, DEH-P6600 R, DEH-P9600 MP
  • DEH-P3100 UB, DEH-P4100 SD, DEH-P5100 UB, DEH-P7100 BT, DEH-P8100 BT
  • DEH-P88RS-II-DEHP88RS
  • And other Pioneer headunits with an IP-BUS port.

It works with most AUX-enabled devices such as smartphones, tablets, and laptops.

Setup Instructions

Follow these steps to install and connect your AUX cable:

  1. Access Stereo Port: Carefully remove your car stereo from its mounting to access the rear ports.
  2. Connect AUX Cable: Locate the IP-BUS (CD changer) port on the back of your Pioneer stereo and firmly plug in the AUX cable connector.
  3. Reinstall Stereo: Securely reinstall your car stereo into its mounting.
  4. Connect Audio Device: Plug the 3.5mm jack of the AUX cable into the headphone port of your smartphone, tablet, or MP3 player.
Close-up of the IP-BUS connector
Figure 2: IP-BUS connector
Close-up of the 3.5mm gold jack
Figure 3: 3.5mm gold jack

Operating Instructions

Once the AUX cable is installed and your audio device is connected:

  1. Turn On Stereo: Power on your car stereo.
  2. Select AUX Input: On your car stereo, switch the input source to AUX, EXT, or CD-CH mode. This activates the input from the AUX cable.
  3. Play Music: Start playing music or audio from your connected smartphone, tablet, or MP3 player. The audio will now be transmitted through your car's speakers.
  4. Adjust Volume: Control the volume using your car stereo's volume knob or your audio device's volume controls.

Safety Precautions

Please read and follow these safety guidelines to ensure safe operation and prevent damage:

  • Approved Power Supply: For safety, use only with approved radio power supplies.
  • Driving Safety: Do not operate or adjust the cable or connected device in a way that distracts you while driving. Always prioritize road safety.
  • Liquid Exposure: Keep the cable and connected devices away from water, rain, or other liquids to prevent damage and electrical hazards.
  • Cable Handling: Avoid kinking, pinching, or stretching the cable excessively, as this can damage the internal wires.

User Tips

  • Ensure your Pioneer headunit explicitly supports an IP-BUS AUX input. Refer to your stereo's manual if unsure.
  • If you experience static or poor audio quality, ensure all connections are secure and try adjusting the volume levels on both your device and car stereo.
  • The 1.5-meter length provides ample reach for most car interiors, allowing flexible placement of your audio device.

Troubleshooting

If you encounter issues, try the following solutions:

  • No Audio Output:
    • Ensure your car stereo is set to the correct input mode (AUX/EXT/CD-CH).
    • Check that the 3.5mm jack is fully inserted into your audio device and the IP-BUS connector is secure in the stereo.
    • Verify that the volume on both your audio device and car stereo is turned up.
    • Test with a different audio device or a different 3.5mm cable (if available) to rule out device or cable issues.
  • Static or Poor Sound Quality:
    • Ensure all connections are tight and free from debris.
    • Try adjusting the volume levels on both your audio device and car stereo; sometimes, one might be too high or too low, causing distortion.
    • Ensure the cable is not running near strong electrical interference sources.

Maintenance

To ensure the longevity and optimal performance of your AUX cable:

  • Cleaning: Use a soft, dry cloth to wipe the cable and connectors. Do not use liquid cleaners or solvents.
  • Storage: When not in use, store the cable in a cool, dry place, away from direct sunlight and extreme temperatures. Avoid tightly coiling or bending the cable sharply.
  • Handling: Always grasp the connectors when plugging or unplugging the cable, rather than pulling on the cable itself.

Frequently Asked Questions (FAQ)

Q: What is the length of the cable?
A: The cable length is 1.5 meters.
Q: Is this cable suitable for Pioneer AVIC D3?
A: It should fit if your AVIC D3 unit has the standard IP-BUS connector. Please consult your car stereo's manual to confirm the presence of an IP-BUS port.
Q: Does it fit Pioneer M77MP?
A: It should fit if your Pioneer M77MP unit has the standard IP-BUS connector. Please consult your car stereo's manual to confirm the presence of an IP-BUS port.

Warranty and Support

For any questions, technical assistance, or support regarding your Biurlink Car Radio Audio Aux Cable, please contact the seller or retailer from whom you purchased the product. Please retain your proof of purchase for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.