Introduction
Thank you for choosing the SKMEI 2686 Sports Men's Military Watch. This watch is designed for outdoor enthusiasts, featuring a robust build and multiple functions including altimeter, barometer, compass, thermometer, pedometer, chronograph, alarm, and more. This manual provides detailed instructions to help you set up, operate, and maintain your watch.

Watch Components and Buttons
Familiarize yourself with the watch's components and button layout for optimal use.


- LIGHT Button (Top Left): Activates the backlight.
- MODE Button (Bottom Left): Cycles through different modes (Time, Alarm, Chronograph, Countdown Timer, Pedometer, Altimeter, Barometer, Compass, Thermometer).
- UP Button (Top Right): Used for adjusting settings (e.g., increasing values, changing units) and starting/stopping functions in certain modes.
- DOWN Button (Bottom Right): Used for adjusting settings (e.g., decreasing values, changing units) and resetting functions in certain modes.
Setup
Initial Power On and Battery
Your SKMEI 2686 watch comes with a pre-installed battery. No initial charging is required. If the display is dim or blank, the battery may need replacement.
Setting Time and Date
- In Timekeeping Mode, press and hold the MODE button until the seconds start flashing. This indicates you are in setting mode.
- Press the MODE button repeatedly to cycle through the settings: Seconds → Hour → Minute → Year → Month → Day.
- Use the UP and DOWN buttons to adjust the flashing value.
- Once all settings are correct, press the MODE button again to exit the setting mode.
Setting Units (Altimeter, Barometer, Thermometer)
Specific instructions for unit settings are not detailed in the provided information. Typically, unit settings are adjusted within the respective mode (e.g., Altimeter mode) by pressing and holding a button (often UP or DOWN) or entering a sub-setting menu via the MODE button.
Operating Instructions
Press the MODE button to cycle through the main functions of the watch.
Backlight
Press the LIGHT button (top left) to illuminate the display for a few seconds.
Altimeter
This function measures your current altitude.

- Press MODE until you reach the Altimeter display.
- The watch will display the current altitude.
- Calibration may be required for accurate readings. Refer to the full manual if available for calibration steps.
Barometer (Pressure Measurement)
The barometer provides real-time atmospheric pressure readings, useful for understanding weather conditions.

- Press MODE until you reach the Barometer display.
- The watch will show the current atmospheric pressure.
Thermometer / Weather Forecast
Understand temperature changes and get a basic weather forecast.

- Press MODE until you reach the Thermometer/Weather display.
- The watch will show the current temperature and a graphical weather trend.
Compass
Indicates direction during your travels.

- Press MODE until you reach the Compass display.
- Hold the watch level and rotate your body until the desired direction is indicated.
- Calibration may be required for accurate readings. Refer to the full manual if available for calibration steps.
Sport Record (Pedometer, Calories, Mileage, Metronome)
Track your activity with 24-hour activity tracking, recording steps, distance, calories burned, and time taken. It also stores 7-day data.

- Press MODE until you reach the Sport Record display (Pedometer).
- The watch will automatically track your steps, calculate calories burned, and distance covered.
- Use UP or DOWN buttons to view different metrics or access 7-day data.
- The Metronome function can be accessed within this mode or a related sub-mode.
Chronograph (Stopwatch)
- Press MODE until you reach the Chronograph display (usually indicated by "00:00:00").
- Press the UP button to start the stopwatch.
- Press the UP button again to pause it.
- Press the DOWN button to reset the stopwatch to zero.
Alarm
- Press MODE until you reach the Alarm display.
- Press and hold the UP button until the hour digits flash.
- Use the UP and DOWN buttons to set the hour.
- Press MODE to move to minute setting, then use UP and DOWN to set minutes.
- Press MODE to exit setting mode.
- Press the DOWN button to toggle the alarm ON/OFF.
Countdown Timer
- Press MODE until you reach the Countdown Timer display.
- Press and hold the UP button to enter setting mode (digits will flash).
- Use UP and DOWN to set the desired countdown time (hours, minutes, seconds).
- Press MODE to confirm each segment and exit setting mode.
- Press the UP button to start the countdown.
- Press the UP button again to pause, and DOWN to reset.
Maintenance
Water Resistance
Your SKMEI 2686 watch is 5 ATM (50 meters) water resistant. This means it is suitable for:
- Daily use
- Washing hands
- Sweating
- Rain exposure
It is NOT suitable for showering, bathing, swimming, diving, or any water sports where it will be submerged.
Cleaning
Wipe the watch case and band regularly with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, followed by drying thoroughly. Avoid using chemical cleaners, as they may damage the watch's finish or seals.
Battery Replacement
The watch uses a standard watch battery. When the display becomes dim or stops functioning, the battery needs to be replaced. It is recommended to have the battery replaced by a qualified watch technician to ensure the water resistance seal is properly maintained.
Troubleshooting
- Display is blank or dim: The battery may be low or depleted. Replace the battery.
- Time is incorrect: Re-set the time as per the "Setting Time and Date" instructions.
- Altimeter/Barometer/Compass readings are inaccurate: These sensors may require calibration. Refer to the full product manual for specific calibration procedures, or try moving to an open area away from magnetic interference for compass readings.
- Buttons are unresponsive: Check if the watch is in a locked mode (if applicable, though not specified). If not, a battery issue or internal fault may be present.
Specifications
| Feature | Specification |
|---|---|
| Brand | Skmei |
| Model Number | 2686 |
| Display Type | Analog-Digital |
| Movement | Digital |
| Case Material | Plastic |
| Band Material Type | Nylon |
| Dial Window Material Type | Resin |
| Case Shape | Round |
| Dial Diameter | 49.7mm |
| Case Thickness | 17.3mm |
| Band Width | 26.2mm |
| Band Length | 24cm |
| Clasp Type | Buckle |
| Water Resistance Depth | 5Bar (50 meters) |
| Battery | Included, Not Rechargeable |
| Features | Chronograph, Alarm, Back Light, LED Display, Complete Calendar, Week Display, Shock Resistant, Pressure Measurement, Steps Tracker, Multiple Time Zone, Stop Watch, Calorie Counter, Altimeter, Compass, Barometer, Thermometer |
| Certification | CE |
User Tips
- Battery Life: To conserve battery life, avoid excessive use of the backlight.
- Accuracy: For best accuracy with altimeter, barometer, and compass functions, ensure the watch is calibrated periodically and used in stable conditions away from strong magnetic fields.
- Water Exposure: Always ensure the watch is dry before pressing any buttons if it has been exposed to moisture, to prevent water ingress.
Frequently Asked Questions (FAQ)
- Q: How do I charge the watch?
- A: The SKMEI 2686 watch operates on a standard watch battery and is not rechargeable. When the battery is depleted, it needs to be replaced.
- Q: What is the size of the watch?
- A: The watch has a dial diameter of 49.7mm and a case thickness of 17.3mm.
- Q: Is the watch fully waterproof?
- A: The watch is 5 ATM (50 meters) water resistant, meaning it can withstand splashes, rain, and hand washing. It is not suitable for swimming, showering, or submersion in water.
Warranty and Support
For warranty information and customer support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.