BEAR FORCE Aluminum Power Washer Gun & Snow Foam Lance Set

Contents

Bear Force Aluminum Power Washer Gun & Snow Foam Lance Set

Instruction Manual

1. Product Overview

Thank you for choosing the Bear Force Aluminum Power Washer Gun and Snow Foam Lance Set. This manual provides essential information for the safe and effective use of your new cleaning tool. Please read it thoroughly before operation.

Bear Force Power Washer Gun and Snow Foam Lance Set components

Figure 1: Complete set of Bear Force Power Washer Gun and Snow Foam Lance components.

Components Included:

  • Aluminum Power Washer Gun
  • Snow Foam Lance (with transparent tank, soap regulator, silicone pickup tube)
  • 5 Spray Tips (0°, 15°, 25°, 40°, 65°/Soap)
  • Nozzle Holder
  • Metal Adapter (specific to selected type: Karcher, Lavor, Nilfisk, or M22-15mm)
  • Additional Orifice Nozzle (1.10mm and 1.25mm)

2. Setup Instructions

Before first use, ensure all components are present and undamaged.

  1. Connect Power Washer Gun to Hose:
    • Identify the M22-ID 14mm Aluminum Alloy Connector at the base of the spray gun handle.
    • If your pressure washer hose has an M22-14mm fitting, connect it directly to the gun.
    • If your pressure washer hose requires an adapter (e.g., Karcher, Lavor, Nilfisk, M22-15mm), first attach the appropriate metal adapter to the gun's M22-14mm inlet, then connect your pressure washer hose to the adapter. Ensure all connections are tight to prevent leaks.
    Connection diagram for standard M22 ID 14/15mm thread connectors

    Figure 2: Standard M22-ID 14/15mm Thread Connector setup.

    Connection diagram for Karcher K2~K7 pressure washers

    Figure 3: Connecting to Karcher K2~K7 pressure washers.

    Connection diagram for Lavor/MAC ALLISTER/AR Blue/Sterwins pressure washers

    Figure 4: Connecting to Lavor/MAC ALLISTER/AR Blue/Sterwins pressure washers.

    Connection diagram for Nilfisk/STIHL/Gerni/BOSCH pressure washers

    Figure 5: Connecting to Nilfisk/STIHL/Gerni/BOSCH pressure washers.

  2. Attach Snow Foam Lance (if using):
    • Ensure the foam lance is assembled with the silicone pickup tube inside the transparent tank.
    • Fill the transparent tank with your desired car wash soap and water mixture. Do not overfill.
    • Connect the foam lance's 1/4" quick connector to the 1/4" QD Coupler on the front of the power washer gun. Push firmly until it clicks into place.
    Details of the snow foam lance

    Figure 6: Snow Foam Lance components and features.

  3. Attach Spray Tip (if not using foam lance):
    • Select the desired spray tip (0°, 15°, 25°, 40°, or 65°/Soap) from the nozzle holder.
    • Pull back the collar on the 1/4" QD Coupler at the front of the gun, insert the spray tip, and release the collar to lock it in place. Tug gently to ensure it is secure.
    The 5 spray tips and their corresponding spray patterns

    Figure 7: The 5 spray tips and their patterns.

3. Operating Instructions

  1. Safety Lock: The power washer gun is equipped with a red safety lock to prevent accidental operation of the trigger. Push the red lever up to engage the lock and down to disengage it. Always engage the safety lock when not actively spraying.
  2. Using the Snow Foam Lance:
    • Once connected and filled, turn on your pressure washer.
    • Adjust the green Soap Regulator knob on top of the foam lance to control the soap concentration. Turn clockwise for more soap, counter-clockwise for less.
    • Aim the foam lance at the surface to be cleaned and press the trigger. Apply an even layer of foam.
  3. Using Spray Tips:
    • Ensure the desired spray tip is securely attached.
    • Turn on your pressure washer.
    • Aim the gun at the surface and press the trigger.
    • Tip Selection:
      • 0° (Red): Pin-point jet, for stubborn stains in small areas. Use with extreme caution.
      • 15° (Yellow): Narrow spray, for intense cleaning of small areas.
      • 25° (Green): Medium spray, for general cleaning tasks.
      • 40° (White): Wide spray, for gentle cleaning of large areas.
      • 65° (Black/Soap): Low-pressure wide spray, typically used for applying detergents or rinsing.
  4. General Operation:
    • Always maintain a safe distance from the surface being cleaned to avoid damage.
    • Keep a firm grip on the gun, as it will recoil slightly when activated.
    • Never point the gun at people, pets, or electrical outlets.
    Demonstration of the high-pressure washer gun in use

    Figure 8: Power Washer Gun in action, showing foam and spray modes.

4. Maintenance

Proper maintenance ensures the longevity and optimal performance of your power washer gun and foam lance.

  1. After Each Use (Foam Lance):
    • Empty any remaining soap solution from the transparent tank.
    • Fill the tank with clean water and run the foam lance for a few seconds to flush out any soap residue from the internal components. This prevents clogging.
    • Rinse the exterior of the foam lance and tank with clean water.
  2. Cleaning Spray Tips: If spray tips become clogged, use a small pin or needle to clear any debris from the orifice. Rinse thoroughly.
  3. Storage:
    • Disconnect the gun and foam lance from the pressure washer hose.
    • Drain any remaining water from the gun and foam lance.
    • Store all components in a clean, dry place, away from direct sunlight and freezing temperatures.
  4. Check Connections: Periodically inspect all connections, O-rings, and seals for wear or damage. Replace if necessary to prevent leaks.

5. Troubleshooting

ProblemPossible CauseSolution
No foam or weak foamSoap concentration too low; Clogged orifice; Insufficient water pressure; Pickup tube blocked.Increase soap concentration; Clean or replace orifice; Ensure pressure washer is operating correctly; Clear pickup tube.
Low pressure or no sprayClogged spray tip; Loose connections; Insufficient water supply to pressure washer.Clean spray tip; Tighten all connections; Check water supply and pressure washer operation.
Leaks from connectionsLoose connections; Worn O-rings or seals.Tighten connections; Inspect and replace O-rings/seals if damaged.

6. Specifications

FeatureSpecification
Max Pressure120 Bar / 1750 PSI
Inlet ConnectorM22-ID 14mm
Outlet Connector1/4" Quick Connector
Gun Body MaterialEngineering Plastic (Nylon Housing)
Internal Gun ComponentsAluminum Valve, Aluminum Tube
Interface MaterialAlloy
Nozzle MaterialAlloy
Water Spray TypeFan (adjustable via tips)
Foam Lance Tank MaterialPET (Corrosion-resistant, with volume scale)
Standard Orifice Size1.10mm (for 60~130bar / 900~1850psi)
Additional Orifice Size1.25mm (for pressure washers above 130bar / 1850psi)
Additional orifice nozzles

Figure 9: Additional orifice nozzles for foam lance.

7. User Tips

  • Pre-Rinse: Always pre-rinse the surface with plain water before applying foam to remove loose dirt and debris.
  • Test First: When using a new cleaning solution or on a new surface, always test on an inconspicuous area first to ensure compatibility and prevent damage.
  • Personal Protective Equipment (PPE): Always wear appropriate eye protection and gloves when operating a pressure washer.
  • Rinse Thoroughly: After applying foam or detergent, rinse the surface thoroughly with clean water to prevent spotting or residue buildup.
  • Optimal Foam: Experiment with different soap-to-water ratios and the soap regulator knob to achieve your desired foam thickness.

8. Warranty and Support

For any warranty claims, technical support, or inquiries regarding your Bear Force Aluminum Power Washer Gun and Snow Foam Lance Set, please contact the seller directly through your purchase platform. Please have your order details ready when contacting support.

© 2023 Bear Force. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.