HLTNC 110ST-M05030, 130ST-M06025, 130ST-M10015, T3DF

Contents

HLTNC AC Servo Motor Kit Instruction Manual

Models: 110ST-M05030, 130ST-M06025, 130ST-M10015 Servo Motors & T3DF RS485 Servo Driver

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your HLTNC AC Servo Motor Kit. Please read this manual thoroughly before using the product to ensure proper handling and to prevent damage or injury. Keep this manual for future reference.

Overview of the HLTNC AC Servo Motor Kit
Figure 1: Overview of the HLTNC AC Servo Motor Kit, showing the servo motor, servo drive, and connecting cables.

2. Package Contents

Upon unpacking, please verify that all items listed below are present and undamaged:

  • HLTNC AC Servo Motor (Specific model based on order: 110ST-M05030, 130ST-M06025, or 130ST-M10015)
  • HLTNC T3DF RS485 Servo Driver
  • Motor Power Cable
  • Motor Encoder Cable
  • Other necessary connectors (as supplied)

If any items are missing or damaged, please contact your supplier immediately.

3. Safety Information

WARNING: Failure to follow these safety instructions may result in electric shock, fire, serious injury, or death.

  • Installation and wiring must be performed by qualified personnel only.
  • Ensure the power supply is disconnected before performing any installation, wiring, or maintenance.
  • Do not touch the motor or drive terminals immediately after power-off, as residual voltage may be present. Wait for capacitors to discharge.
  • Ensure proper grounding of the motor and drive to prevent electric shock.
  • Do not operate the motor or drive in environments with flammable gases, liquids, or corrosive substances.
  • Protect the equipment from moisture, dust, and direct sunlight.
  • Ensure adequate ventilation around the servo drive to prevent overheating.
  • Moving parts of the motor can cause injury. Ensure all safety guards are in place before operation.

4. Setup and Installation

4.1 Mounting the Servo Motor

  • Mount the servo motor securely to a rigid, vibration-free surface using appropriate fasteners.
  • Ensure proper alignment with the load to prevent excessive stress on the motor shaft and bearings.
  • Refer to the motor's dimensional drawings in the Specifications section for mounting hole patterns and shaft dimensions.

4.2 Mounting the Servo Driver

  • Mount the servo driver vertically inside an electrical enclosure to facilitate proper heat dissipation.
  • Ensure sufficient clearance around the drive for airflow.
  • Avoid mounting near heat sources or in direct sunlight.

4.3 Wiring Connections

IMPORTANT: All wiring must be done with power disconnected. Refer to the T3DF Servo Driver's specific wiring diagram for detailed terminal connections. The following is a general guide:

  1. Power Wiring: Connect the main AC power supply (220V) to the designated input terminals on the T3DF servo driver. Ensure correct phase connections (L1, L2, L3 for 3-phase, or L, N for single-phase if applicable). Connect the protective earth (PE) terminal to a reliable ground.
  2. Motor Power Cable: Connect the motor power cable from the servo driver's output terminals (U, V, W) to the corresponding terminals on the servo motor.
  3. Motor Encoder Cable: Connect the motor encoder cable from the servo driver's encoder input port to the encoder port on the servo motor. This provides feedback for precise motor control.
  4. Control Signal Wiring: Connect control signals (e.g., pulse/direction, analog input, RS485 communication) from your controller (PLC, CNC, etc.) to the appropriate input terminals on the T3DF servo driver. Ensure correct polarity and shielding for signal integrity.
  5. Brake Wiring (if applicable): If your motor model includes a brake, connect the brake power supply to the designated terminals on the servo driver or an external power source as per the drive's manual.

5. Operating Instructions

5.1 Initial Power-Up

  1. Double-check all wiring connections for correctness and security.
  2. Apply power to the servo driver. Observe the drive's display for any error codes.
  3. If an error occurs, refer to the Troubleshooting section or the T3DF drive manual.

5.2 Parameter Setting

  • The T3DF servo driver requires parameter configuration to match the specific motor and application requirements.
  • Parameters typically include motor type, encoder resolution, control mode (position, speed, torque), gain settings, and communication settings (for RS485).
  • Refer to the T3DF servo driver's user manual for detailed instructions on parameter setting via its keypad/display or communication interface.

5.3 Test Run

  • After parameter setup, perform a low-speed, no-load test run to verify basic motor operation and direction.
  • Gradually increase speed and load while monitoring motor temperature, vibration, and drive status.
  • Adjust gain parameters as needed to achieve stable and responsive control.

6. Maintenance

Regular maintenance helps ensure the longevity and reliable operation of your servo motor kit.

  • Periodic Inspection: Regularly inspect all wiring connections for looseness or damage. Check for any signs of overheating, unusual noises, or vibrations.
  • Cleaning: Keep the motor and drive free from dust, dirt, and debris. Use a soft, dry cloth or compressed air for cleaning. Do not use solvents that may damage plastic parts.
  • Environmental Conditions: Ensure the operating environment remains within specified temperature and humidity ranges.
  • Fastener Check: Periodically check mounting bolts and screws for tightness.

7. Troubleshooting

This section provides solutions for common issues. For detailed error codes and advanced troubleshooting, refer to the T3DF servo driver's user manual.

ProblemPossible CauseSolution
Motor does not moveNo power to drive; Incorrect wiring; Drive in fault state; Incorrect parameters; No command signal.Check power supply; Verify all wiring; Clear drive fault; Check/adjust parameters; Verify command signal from controller.
Motor vibrates excessivelyImproper gain settings; Mechanical resonance; Loose mounting; Encoder issue.Adjust servo gains (P, I, D); Check mechanical system for resonance; Tighten mounting bolts; Check encoder connection/function.
Drive displays error codeOvercurrent, overvoltage, undervoltage, encoder error, overload, etc.Refer to T3DF manual for specific error code meaning and troubleshooting steps. Address the root cause (e.g., check motor load, power supply, wiring).
Motor overheatsExcessive load; Continuous operation at high torque; Insufficient cooling; Incorrect motor parameters.Reduce load; Check duty cycle; Ensure proper ventilation; Verify motor parameters match actual motor.

8. Specifications

8.1 HLTNC T3DF RS485 Servo Driver

Dimensional drawing and technical parameters for the T3DF RS485 Servo Drive
Figure 2: T3DF RS485 Servo Drive Dimensions and Parameters
ParameterValue
ModelHT-T3DF-RS485-8-80AC
Voltage220V
Phase3PH
Frequency50/60Hz
Max Current12A
Weight1.5 kg
Dimensions (H x D x W)185mm x 160mm x 52mm

8.2 HLTNC 110ST-M05030 Servo Motor

Dimensional drawing and specifications for the 110ST-M05030 Servo Motor
Figure 3: 110ST-M05030 Servo Motor Dimensions and Specifications
ParameterValue
Model110ST-M05030
Rated Power1.5 KW
Rated Voltage220 V
Rated Current5.0 A
Rated Speed3000 RPM
Peak Torque15 Nm
Weight8.8 kg
Shaft Diameter28 mm
Shaft Length50 mm
Motor Body Size110 x 110 mm
Mounting Hole Spacing130 mm

8.3 HLTNC 130ST-M06025 Servo Motor

Dimensional drawing and specifications for the 130ST-M06025 Servo Motor
Figure 4: 130ST-M06025 Servo Motor Dimensions and Specifications
ParameterValue
Model130ST-M06025
Rated Power1.5 KW
Rated Voltage220 V
Rated Current5.0 A
Rated Speed2500 RPM
Peak Torque18 Nm
Weight12.4 kg
Shaft Diameter28 mm
Shaft Length50 mm
Motor Body Size130 x 130 mm
Mounting Hole Spacing145 mm

8.4 HLTNC 130ST-M10015 Servo Motor

Dimensional drawing and specifications for the 130ST-M10015 Servo Motor
Figure 5: 130ST-M10015 Servo Motor Dimensions and Specifications
ParameterValue
Model130ST-M10015
Rated Power1.5 KW
Rated Voltage220 V
Rated Current5.0 A
Rated Speed1500 RPM
Peak Torque25 Nm
Weight17.0 kg
Shaft Diameter28 mm
Shaft Length50 mm
Motor Body Size130 x 130 mm
Mounting Hole Spacing145 mm

9. User Tips

No specific user tips or common issues were available from provided reviews or Q&A. Always ensure proper grounding and secure connections for optimal performance and safety.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer's authorized service center. Please have your product model and serial number ready when contacting support.

© 2023 HLTNC. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.