PowMr POW-LVM4K-ECO

Contents

PowMr 4kW MPPT Solar Inverter User Manual

Model: POW-LVM4K-ECO

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your PowMr 4kW MPPT Solar Inverter. This multifunctional solar inverter integrates an MPPT solar charge controller, a high-frequency pure sine wave inverter, and a UPS function module, ideal for off-grid backup power and self-consumption applications. It can operate with or without batteries.

The inverter features a 4kW/4kVA rated power with a power factor of 1, a wide MPPT range of 60V~450V (500Voc max), pure sine wave AC output, and built-in WiFi for remote monitoring. It supports CAN/RS485 for BMS communication and offers dual AC outputs with grid feed-in capability.

System Overview

PowMr 4kW MPPT Solar Inverter Front View
Front view of the PowMr 4kW MPPT Solar Inverter (POW-LVM4K-ECO) highlighting key features like 4KW 110V, 100A Current, 5000W PV, 60-450VDC PV input, and 24V Battery compatibility.
PowMr Inverter Product Overview and Dimensions
Product Overview with labeled indicators and buttons. Dimensions: 17.2" (43.8 cm) H x 12.8" (32.5 cm) W x 4.3" (11 cm) D. Weight: 7.5 kg (16.5 lb).
PowMr Inverter Rear Connection Panel
Rear connection panel showing AC IN, OUT1, COM, BMS, BAT+, BAT-, and PV IN terminals.
Typical System Connection Diagram
Typical system connection diagram for the PowMr Hybrid Solar Inverter. It illustrates connections for PV Array (Max 500Vdc), 24V Battery (≥200Ah), Utility Grid (via 40A AC Circuit Breaker), and Home/Office Loads. Grounding is also shown.

2. Safety Instructions

WARNING! This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  • Ensure you understand your battery system type (lithium or lead-acid) before connection. Incorrect selection can prevent normal operation.
  • Read all instructions and cautionary markings on the unit, batteries, and this manual before use.
  • All operations and connections must be performed by professional electrical or mechanical engineers.
  • All electrical installations must comply with local electrical safety standards.
  • When installing PV modules during the daytime, cover them with opaque materials to avoid dangerous high terminal voltage.
  • CAUTION: To reduce risk of injury, charge only deep-cycle lead-acid or lithium rechargeable batteries. Other battery types may burst.
  • Do not disassemble the unit. Refer to a qualified service center for repairs. Incorrect re-assembly poses risks of electric shock or fire.
  • Disconnect all wirings before maintenance or cleaning to reduce electric shock risk. Turning off the unit alone is not sufficient.
  • NEVER charge a frozen battery.
  • Follow cable size specifications for optimum inverter operation.
  • Be cautious with metal tools around batteries to prevent short circuits and explosions.
  • Strictly follow installation procedures for disconnecting AC or DC terminals.
  • This inverter must be connected to a permanent grounded wiring system, complying with local regulations.
  • NEVER short circuit AC output and DC input. Do NOT connect to the grid if DC input is short-circuited.
  • Ensure the inverter is completely assembled before operation.

Labels on Inverter and in Documentation

  • CAUTION: Do not disconnect under load!
  • Danger: High Voltage! Electrical Hazard!
  • Maintenance: Start maintaining at least 5 minutes after disconnecting all external power supplies.
  • Read Manual: Read instructions carefully before any operation.
  • Grounding: System must be firmly grounded for operator safety.
  • WARNING! High level of potential danger, which, if not avoided, could result in death or serious injury.
  • CAUTION! Moderate or low level of potential danger, which, if not avoided, could result in moderate or minor injuries.

3. Setup and Installation

3.1 Unpacking and Inspection

Upon receiving the product, inspect the outer packaging for damage. Open the box and check if the internal equipment is intact. If any damage is found, contact your local distributor immediately.

3.2 Installation Tools

The following tools are recommended for installation:

  • Multi-meter
  • Protective gloves
  • Insulated anti-smashing shoes
  • Safety glasses
  • ESD wrist strap
  • Hammer drill
  • Electric screwdriver
  • Cross screwdriver
  • Rubber mallet
  • Spirit level
  • Wire cutter / stripper
  • Terminal crimping tool

3.3 Mounting Unit

Consider the following points for optimal installation:

  • Do not mount on flammable construction materials.
  • Mount on a solid, non-combustible surface (e.g., concrete).
  • Install at eye level for easy LCD display reading.
  • Ambient temperature should be between -10°C and 60°C.
  • Mount vertically on the wall.
  • Ensure at least 30cm clearance on all sides (top, bottom, left, right) for heat dissipation and wiring access.

WARNING! Inverter is suitable for mounting on concrete or other non-combustible surface only.

Mounting Steps:

  1. Use an Ø8 drilling bit to drill two holes 160mm apart on the mounting surface. Insert M6 expansion screw tubes.
  2. Align the inverter's top screw holes with the installed expansion screws and fix it to the wall.
  3. Before connecting wires, remove the bottom cover by unscrewing four screws.

3.4 AC Input / Output Connection

CAUTION! Install a separate 40A AC breaker between the inverter and AC input power source for safety and maintenance.

CAUTION! Do NOT mis-connect input and output connectors. Ensure correct polarity (L and N wires). N wires of input and output must NOT be connected together.

WARNING! All wiring must be performed by qualified personnel. Use recommended cable sizes.

  • AC Input: 8 AWG (8.37 mm²)
  • AC Output: 8 AWG (8.37 mm²)

WARNING! Disconnect AC power before connecting. All operations must comply with local laws and regulations.

Connection Steps (AC IN/OUT):

  1. Switch off AC circuit breaker.
  2. Remove 12mm insulation from cable ends, shorten conductor to 10mm. Insert into tubular terminal and crimp tightly.
  3. Insert AC cables into terminal blocks according to polarities (PE: yellow-green, L: brown/black, N: blue). Tighten screws. Connect PE first.

3.5 PV Connection

CAUTION! Install a separate DC circuit breaker between the inverter and PV modules.

WARNING! Do not ground positive or negative PV terminals. Exposure to sunlight generates lethal high voltages. Connect PV terminals to corresponding ports; reversing polarity damages the inverter.

  • PV Module Connection: 10 AWG (5.26 mm²)

PV Module Selection Parameters:

  • Max. PV Array Open Circuit Voltage: 500Vdc
  • Start-up Voltage: 70Vdc
  • PV Array MPPT Voltage Range: 60Vdc~450Vdc

Connection Steps (PV):

  1. Switch off DC circuit breaker.
  2. Prepare PV cables (12mm insulation removed, 10mm conductor, crimped into tubular terminals).
  3. Use a multi-meter to check polarities (+PV: Red, -PV: Black).
  4. Insert PV cables into terminal block according to polarities and tighten screws.

3.6 Battery Connection

CAUTION! Install a separate DC over-current protector or disconnect device (recommended 250A) between battery and inverter.

WARNING! All wiring by qualified personnel. Use recommended cable sizes. Disconnect AC power before connecting battery.

  • Battery Connection: 1 AWG (42 mm²)

For lead-acid batteries, recommended charge current is 0.3C (C ≤ battery capacity).

Connection Steps (Lead-acid Battery):

  1. Unscrew pre-fixed screws on battery poles. Prepare 2 DT terminals for AWG1 cables.
  2. Prepare battery cables (12mm insulation removed, 10mm conductor, crimped into DT terminals).
  3. Pass battery cable through bottom shell hole, ensuring positive terminal passes through the red protective sleeve. Tighten terminal screws. Verify polarity at both battery and inverter.
  4. Connect all battery packs. Suggested minimum capacity: 200Ah.

Lithium Battery Connection:

WARNING! Shock Hazard. High battery voltage in series. Install with care.

CAUTION! Do not place anything between inverter terminal and DT terminal. Do not apply anti-oxidant substance before connecting. Ensure positive to positive and negative to negative connections.

  1. Follow lead-acid battery power cable connection steps.
  2. Connect RJ45 terminal of battery communication cable to BMS communication port of inverter (RS485 or CAN protocol).
  3. Insert the other end of RJ45 cable to the lithium battery's communication port.

BMS Port Pin Assignment:

Pin NumberBMS Port
1RS485B
2RS485A
3-
4CANH
5CANL
6-
7-
8-

3.7 Final Assembly

After all wiring is complete, reattach the bottom cover by screwing in the four screws.

3.8 Smart Communication Stick Connection (Optional)

Insert the smart communication stick (WiFi) directly into the COM port to connect to the cloud platform for monitoring. Refer to the solar APP quick configuration guide for built-in WiFi models.

4. Operation

4.1 Power ON/OFF

Once the unit is properly installed and batteries are connected, press the ON/OFF switch (located on the bottom of the case) to turn on the unit.

4.2 Operation and Display Panel

The front panel features four indicators, four function keys, and an LCD display to show operating status and power information.

LED Indicators:

  • AC Indicator (Green): Solid On (grid normal, grid power operation), Flashing (grid normal, not in grid power operation), Off (grid abnormal).
  • Invert Indicator (Yellow): Solid On (output powered by battery/PV in battery mode), Off (other states).
  • Charging Indicator (Yellow): Solid On (battery in float charging), Flashing (battery charging at constant voltage/current), Off (other states).
  • Fault Indicator (Red): Solid On (fault occurs), Flashing (warning condition occurs), Off (inverter working properly).

Function Buttons:

  • ESC: Exit setting mode.
  • UP (▲): Go to previous selection or adjust parameter up.
  • DOWN (▼): Go to next selection or adjust parameter down.
  • ENTER (✔): Confirm selection or enter setting mode.

LCD Display Icons:

The LCD displays various icons indicating battery status (type, voltage, current), AC input/output (voltage, frequency, power), PV input (power, voltage, current), load capacity, and system information. Refer to the full user manual for a detailed description of each icon.

4.3 LCD Settings

To enter setting mode, press and hold the ENTER button for 2 seconds. Use UP/DOWN to select programs and ENTER to confirm. The inverter offers extensive configurable parameters for battery type, charging currents, voltage thresholds, output priorities, and more. For a complete list and detailed instructions on each setting program (00-99), please refer to the comprehensive PDF user manual.

4.4 Display Information

The LCD display cycles through various information screens by pressing UP or DOWN. If idle, it defaults to daily PV power generation. Information displayed includes daily/total solar power generation, lithium battery voltage/current/temperature/SOC/capacity, and inverter firmware version.

5. Maintenance

5.1 Battery Equalization

The equalization function helps reverse negative chemical effects in lead-acid batteries like stratification and sulfation, which can reduce battery capacity. It is recommended to equalize lead-acid batteries periodically.

Note: Do NOT activate this mode when using lithium batteries.

How to Apply Equalization Function:

You can enable battery equalization via LCD setting Program 32 (setting time) or Program 35 (immediate equalization). This involves setting equalization voltage point (Program 31), charging time (Program 32), delay time (Program 33), and interval time (Program 34).

6. Troubleshooting

The inverter provides fault codes and alarm codes to help diagnose issues. When a fault occurs, the fault indicator stays on, the buzzer sounds, and the system attempts an automatic restart. If issues persist after 6 restarts within 15 minutes, the device enters a fault state requiring manual power cycle or a 15-minute wait.

6.1 Fault Reference Codes

Fault codes indicate critical issues. The inverter enters fault mode with a constant red LED and LCD displaying the code. Examples include:

  • Code 1: Grid soft start fail
  • Code 2: Bus over voltage
  • Code 3: Bus below voltage
  • Code 4: Battery over current
  • Code 5: System over temperature
  • Code 14: Over load
  • Code 26: BMS fault
  • Code 30: PV over voltage

For a complete list of fault codes, their meanings, trigger conditions, and resume conditions, please consult the full PDF user manual (pages 57-59).

6.2 Alarm Reference Codes

Alarm codes indicate non-critical issues. The inverter does not enter fault mode; the red LED flashes, and the LCD displays the alarm code. Examples include:

  • Code 50: Battery open
  • Code 51: Battery under voltage
  • Code 52: Battery low voltage
  • Code 56: BMS loss
  • Code 58: Fan error
  • Code 60: Overload (alarm)

For a complete list of alarm codes, their meanings, trigger conditions, and resume conditions, please consult the full PDF user manual (pages 60-61).

6.3 Troubleshooting Table

This table provides common problems, their fault events, trigger conditions, and recommended solutions.

ProblemFault EventTrigger ConditionsWhat to do
LED screen display fault code 2Bus voltage highTotal rated voltage of PV string exceeds Max. PV open circuit voltage.Reduce the PV module number.
LED screen display fault code 5Over temperatureFan not rotating, dust filter dirty, insufficient clearance (<30cm), ambient temp >45°C.Check fan/wiring, clean filter, ensure clearance, avoid direct sunlight.
LED screen display fault code 26BMS faultBMS fault information via battery background controller.Handle battery problems according to fault information.
LED screen display fault code 56BMS lossCommunication cable incorrect, dial switch setting inconsistent, port pin definition mismatch, BMS protocol mismatch.Check/replace cable, verify settings, replace battery/inverter for test.
LED screen display fault code 58Fan abnormal alarmFan rotation abnormal, foreign object, fan not connected, wiring loose, fan damaged.Remove objects, ensure connection, replace fan.
LED screen display fault code 62PV Energy WeakPV power not normal, PV power lower than load demand.Repair PV, remove part of the load.

For a comprehensive troubleshooting guide, refer to the full PDF user manual (pages 63-64).

7. Specifications

CategoryParameterValue
AC InputRated Input Voltage (VAC)110/120; L+N+PE
Voltage Range (VAC)90~140V (APP/GEN/UPS mode)
Frequency (Hz)50/60 (Auto Adaptive)
AC OutputRated Capacity (kW/kVA)4 (Output power reduced if set to 100/110V, current limited at 33A)
Surge Power (kVA)8
Voltage (VAC)100/110/120/127
Power Factor (PF)1
Frequency (Hz)50/60
Switch Time (ms)10 (APP/UPS mode) / 20 (GEN mode)
Wave FormPure SineWave
Charger (PV/AC)Solar Charger TypeMPPT
Max. PV Input Current/Power (A/kW)18/5000
MPPT Range@Operating Voltage (VDC)60-450
PV Start up Voltage(VDC)70
Max. PV Open Circuit Voltage (VDC)500
Max. Charge Current (PV+AC) (A)100
BatteryNormal Voltage (VDC)24V
TypeLithium/Lead-acid
General DataHMILCD
InterfaceRS232/RS485/CAN/Dry Contact
MonitoringWiFi (built-in)
Ingress ProtectionIP21
Max. Operating Altitude (m)4000 (Derating above 2000)

8. User Tips

  • Ensure all connections are secure and properly torqued to prevent loose connections, which can lead to arcing or system instability.
  • Double-check battery polarity before making the final connection to avoid damage to the inverter or batteries.
  • For optimal performance and longevity, ensure adequate ventilation around the inverter to prevent overheating.
  • Regularly check the dust filter and clean it as needed to maintain efficient cooling.
  • When configuring settings, especially for battery parameters, refer to your battery manufacturer's specifications to ensure compatibility and prevent overcharging or deep discharging.

9. Support and Further Information

For detailed LCD setting configurations, comprehensive fault and alarm code lists, and advanced troubleshooting steps, please refer to the complete PDF user manual:

Download Full User Manual (PDF)

For technical assistance or warranty inquiries, please contact PowMr customer support.

© 2023 PowMr. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.