INSE VM6

Contents

INSE Steam Mop Cleaner VM6 User Manual

Model: VM6

Brand: INSE

Important Safety Instructions

⚠ Warning

To reduce fire, electric shock, or personal injury, please read all instructions carefully before using this steam floor washer. Only suitable for household use.

  • This appliance can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning safe use and understanding of hazards. Children should not play with the appliance.
  • Do not leave the appliance unattended while it is connected to the supply mains.
  • The filling aperture must not be opened during use.
  • Do not use the appliance if it has been dropped, shows visible signs of damage, or is leaking.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
  • Keep the appliance out of reach of children when it is energized or cooling down.
  • Before filling with water, ensure the appliance is in a safe state.
  • When the floor washer is not in use and before maintenance, the power cord must be unplugged from the power socket.
  • Do not use damaged power cords or plugs. Improper reassembly or maintenance may cause electric shock or personal injury.
  • To prevent electric shock, do not immerse the steam floor washer in water or any other liquid.
  • Do not touch the power plug or the steam floor washer with wet hands, or operate with bare feet.
  • Do not use the power cord to pull the floor washer, use it as a handle, clamp it in a door crack, or pull it along sharp edges/corners. Do not roll the steam floor washer over the power line. Keep the power cord away from heating surfaces.
  • To unplug, grasp the power plug, not the cord. Do not use extension cords or sockets with insufficient current carrying capacity.
  • Unplug before maintenance.
  • Do not add water to the water tank or install the mop head if the power cord is still plugged in. Unplug, allow to cool, then add water or disassemble the mop head.
  • Before cleaning the outside, unplug the power cord and clean with a dry cloth. Do not spill water on the steam floor washer, or use alcohol, benzene, or paint thinner.
  • To avoid circuit overload, do not operate other equipment on the same circuit as the steam floor washer.
  • To avoid scalding, unplug the power plug and let the appliance cool before removing or replacing accessories.
  • Do not turn over the steam floor washer or spray steam toward people, pets, or plants.
  • Do not use the product as a heating facility.
  • Be careful when using near children, pets, or plants.
  • Do not add detergent, perfume, oil, or other chemicals to the water, as this may damage the appliance or cause unsafe use. Use purified water.
  • Only use accessories recommended by the manufacturer.
  • Do not put any foreign matter into the steam nozzle. Do not use if the steam nozzle is blocked.
  • Keep hands and feet away from the steam floor washer; the steam makes the machine very hot.
  • Only use this product on horizontal and flat ground. Do not use on walls, counters, or windows.
  • Do not use on leather, waxed furniture, synthetic fiber, velvet, or other delicate, steam-sensitive materials.
  • Do not store or place the steam floor washer in a location for too long without removing the mop pad, as this may damage the ground.
  • Do not use the steam floor washer without a mop pad.
  • Keep the work area well lit.
  • Store the steam floor washer indoors in a cool and dry place.
  • Do not lift the steam floor washer when using it.
  • The steam ejected is very hot and may cause burns. Be careful when using.
  • Do not scrub any area for a long time.
  • Do not use on wood floors without wax sealing or unglazed tile floors. Using on waxed floors may cause loss of luster. Always test on a small, inconspicuous area first and check floor manufacturer's instructions.
  • Under normal circumstances, it takes 30 seconds to generate steam. Initial use may take longer.
  • To prolong the service life, it is recommended to use pure water.

Product Overview

INSE VM6 Steam Mop Cleaner with various attachments
The INSE VM6 Steam Mop Cleaner comes with a main unit and multiple accessories for versatile cleaning.
Diagram of INSE VM6 Steam Mop parts with numbered labels.
Exploded view of the steam mop and its components.

Parts List

  1. Handle
  2. Winding hook
  3. Telescopic rod adjustment switch
  4. Telescopic aluminum rod
  5. Steam switch
  6. Motor button
  7. Motor indicator light
  8. Steam indicator light
  9. Water tank
  10. Electric rotating mop head
  11. Circular dual material mop pad
  12. Curved nozzle
  13. Big round brush
  14. Crevice brush
  15. Window scraper
  16. Scraper head
  17. Small round brush
  18. Towel set
  19. Direct nozzle
  20. Measuring cup

Setup and Assembly

1. Handle and Telescopic Rod Installation

Align the semicircular notch of the aluminum rod mouth with the semicircular protrusion of the handle connector. Press the upper and lower buckles of the handle connector, align the aluminum rod mouth, and insert the circular buckles into the upper and lower circular holes of the aluminum rod. To disassemble, press the button to pull out the handle.

Diagram showing assembly of the steam mop handle and telescopic rod.
Assembly of the steam mop handle and telescopic rod.

2. Mop Head and Pad Installation

Align the two circular mop pads with the left and right wheels respectively, and gently press them on the left and right wheels to firmly adhere.

Diagram showing how to attach the circular mop pads to the electric rotating mop head.
Attaching the circular mop pads to the electric rotating mop head.

3. Main Body and Mop Head Connection

Align the snap hole at the lower end of the fuselage with the snap direction of the base interface buckle, and insert it downward into the base interface until it clicks in place. When disassembling, press the base interface buckle, and the body can be pulled out.

Diagram illustrating how to connect the main body to the electric rotating mop head.
Connecting the main body to the electric rotating mop head.

4. Telescopic Rod and Main Body Connection/Disassembly

Insert the snap of the telescopic aluminum rod into the fixing hole of the telescopic rod of the fuselage until a click is heard. Press the telescopic rod removal switch in the direction of the arrow in the right figure, and pull out the telescopic aluminum rod upward to remove it.

Diagram showing connection and disassembly of the telescopic aluminum rod from the main body.
Connecting and disconnecting the telescopic aluminum rod from the main body.

5. Height Adjustment

The product height is adjustable from 1m to 1.2m. Pull the telescopic lever switch clockwise to release the fixing block and adjust the height. Once the ideal height is reached, pull the switch anticlockwise to fasten the fixing block.

6. Adding Water

Push the water tank push button upward to remove the water tank. Unscrew the water tank cover, fill the measuring cup with water, cover the water tank cover, and install it back on the main body.

7. Power Cord Storage

The winding hook easily stores the power cord.

8. Accessory Installation

Align the snap of the straight nozzle with the snap hole of the main engine and insert it into the interface of the main engine. To connect other accessories, refer to the provided diagrams for proper attachment.

Diagram showing how to attach various steam mop accessories to the main engine.
Various accessories and their attachment points for different cleaning tasks.
Multiple accessories included with the INSE VM6 Steam Mop.
Overview of the multiple accessories included with the steam mop, such as mop pads, various nozzles, and brushes.

Operating Instructions

1. Getting Ready

After the power cord is plugged in, the panel light flashes once, and the whole machine enters the standby state.

2. Hot Steam Ready

Plug in the power supply, then press the Steam Option button. The green steam light will flash. The floor mop will then start emitting steam and heating. The green steam light will remain on once heating is complete.

Control panel with steam power mode (Less, Normal, Large) and rotating on/off.
The control panel allows selection of steam power mode and rotating function.

3. Button Controls

  • Steam Option: Press to select the steam flow mode: Less Steam, Medium Steam, or Large Steam.
  • Rotating On/Off: Press to turn on/off the rotating mode of the floor mop head.
  • Short Press (Steam Option Button):
    • One press: Less Steam.
    • Two presses: Medium Steam.
    • Three presses: Large Steam.
    • Four presses: Turn off steam. (Cycles in sequence)
  • Long Press (Steam Option Button): Press and hold for 3 seconds to shut down both steam and rotating functions simultaneously.

4. LED Indicator

  • Rotating Lights:
    • Rotating Status: Light stays on.
    • Non-Rotating Status: Light is off.
  • Steam Lights:
    • Start Heating Mode: Green light flashes.
    • Less Steam Mode: Green light stays on.
    • Medium Steam Mode: Blue light stays on.
    • Large Steam Mode: Red light stays on.
  • Water Shortage Protection: When the water tank is low on water, the steam indicator light and the steam indicator light will flash 6 times alternately, then the power supply to the heater and water pump will turn off.
Video demonstrating the assembly and basic operation of the INSE VM6 Steam Mop.

Maintenance

  • Always unplug the appliance from the power socket before performing any maintenance or cleaning.
  • Clean the exterior of the steam floor washer with a dry cloth. Do not use water, alcohol, benzene, or paint thinner on the exterior.
  • Replace mop pads if they become damaged or excessively dirty. The circular dual material mop pads are machine washable and reusable.
  • To prolong the service life of the steam floor washer, it is recommended to use purified water to prevent mineral buildup.
  • Allow the appliance to cool down completely before removing or replacing any accessories to prevent scalding.
  • Store the steam floor washer indoors in a cool and dry place when not in use.

Troubleshooting

1. The steam floor washer does not generate steam

  • Ensure the power plug is firmly inserted into the power socket.
  • Verify the water tank is full, the power supply is connected, and the mode button is on.
  • If the indicator light is not on, try using another power outlet.
  • If the indicator light flashes, press the mode button to select the cleaning gear.
  • If the indicator light is always on, wait 30 seconds for the steam floor washer to complete preheating.
  • If the issue persists, contact customer service.

2. The steam floor washer generates steam intermittently

  • Select the "high" mode if more steam is required.
  • Confirm that the water tank is full.

3. Cleaning gear cannot be selected

  • Ensure the power plug is inserted and the indicator light flashes.
  • If steam is generating but the indicator light is not on, contact customer service.

4. After cleaning, the floor surface is dirty, with traces or spots

  • Replace with a clean mop pad. Mop pads washed with detergent may be damaged and need replacement.
  • Refer to the floor manufacturer's maintenance and repair instructions before using this product.

5. It is difficult to push and pull the floor washer

  • If the mop pad is not wet enough, it may be difficult to push and pull. It becomes easier after a few minutes of operation.
  • An overly dirty pad can also make it difficult to push and pull. Use a clean mop pad.

6. The rotating disk does not rotate or sway

  • The steam floor washer may be in an upright position. Tilt the handle down to use the washer.
  • The mop pad may be misaligned. Turn off power, unplug, wait for the mop pad to cool, then reinstall.

7. Vibration or swing of steam floor washer

  • The mop pad is not centered on the rotating disk. Turn off power, unplug, wait for the mop pad to cool. Reinstall following the steps in the "Setup and Assembly" section.

Specifications

ParameterValue
Product ModelVM6
Rated VoltageAC 230V
Rated Frequency50/60Hz
Rated Power1300W
Water Tank Capacity330mL
Rotating Speed of Rotary Table110-130 RPM
Steam Volume16-28g/min

Hazardous Substances Information

The content of hazardous substances in all homogeneous materials of this component is below the limit specified in GB/T26572, ensuring compliance with safety standards.

Warranty and Support

Warranty Activation

Activate your 1-year warranty within one month of purchase. Scan the QR code with your phone and provide your Order Number. After activation, your VM6 Steam Mop will be covered for parts and labor for 1 year from the date of purchase, subject to the terms of the guarantee.

Customer Support

If you encounter problems not listed in the troubleshooting section or require further assistance, please contact us via email:

Email: help@vacservice.vip

Most questions can be resolved by our trained VM6 Steam Mop Aftersales Service staff.

For a complete electronic user manual and detailed warranty information, please refer to the official PDF document: INSE Steam Mop VM6 User Manual (PDF)

User Tips

  • Always use purified or distilled water to prevent mineral buildup and prolong the life of your steam mop. Tap water can leave mineral deposits that may affect performance over time.
  • Pre-sweep or vacuum your floors before steam cleaning for best results. This removes loose dirt and debris, allowing the steam mop to focus on deep cleaning.
  • For heavily soiled areas or stubborn stains, allow the steam mop to sit over the spot for a few extra seconds to loosen grime before scrubbing.
  • Regularly wash the mop pads after each use to maintain optimal cleaning effectiveness and hygiene. Machine washing is recommended.
  • When using the steam mop for the first time on a new floor type or a delicate surface, always test it on an inconspicuous area first to ensure compatibility and prevent damage.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.