Hcalory HBH-3S

Contents

Hcalory HBH-3S 8KW Diesel Air Heater User Manual

Model: HBH-3S | Brand: Hcalory

1. Introduction

1.1 Product Overview

Diesel heaters are on-board heating devices that are independent of the automobile engine. They feature their own fuel lines, circuits, combustion heating devices, and control devices. Originally used to preheat car engines and cabs in cold environments to prevent cold start wear, diesel heaters now have a wider range of uses. They can serve as space heating equipment in tents, indoors, and RVs, enhancing comfort for users during living and traveling.

1.2 Principles of Operation

Heat Source:

Upon startup, the ignition plug heats for 1-3 minutes. The fan then delivers air to the combustion chamber, and the diesel pump injects diesel. The atomized diesel mixes with air and burns upon contact with the high-temperature ignition plug, generating significant heat. High-temperature exhaust gases are discharged through the exhaust gas outlet.

Heating:

Heat from the combustion chamber is rapidly transferred to an aluminum heat exchanger and dissipated into the warm air duct via aluminum fins. An external fan blows air around the heat exchanger, and the heated air is then expelled from the warm air outlet.

Control:

The device features an embedded controller. Users can control the device via a connected switch panel to monitor status, adjust settings, and schedule operations. Remote control and a dedicated Hcalory mobile application are also available for remote operation.

1.3 Internal Key Parts Terminology

Understanding the internal components is crucial for maintenance and repair.

Exploded view of Hcalory HBH-3S Diesel Air Heater components
Exploded view of the Hcalory HBH-3S Diesel Air Heater, showing the control box, ignition plug, safety plug, air outlet, combustion chamber, heating zone, air inlet, air fan, and flame retardant impeller.

2. Safety Instructions

Please read all safety warnings, instructions, illustrations, and instruction manuals provided with this diesel heater carefully. Failure to follow all instructions may result in electric shock, fire, or serious injury.

  1. Do not replace important parts of the diesel heater without authorization. For repairs or part replacements, contact customer service for correct product specifications and models. Using incorrect specifications may damage the combustion system.
  2. The heater must not be used in areas where flammable vapors or dust may be present, such as:
    • Fuel depots, carbon depots, timber depots, granaries, and similar locations.
    • Diesel/gas stations. Keep away from fuel tanks, compression tanks, fire extinguishers, clothing, and other flammable items.
  3. Use the machine safely and understand its hazards. Children are not permitted to play with this machine. Cleaning and maintenance must not be carried out unsupervised by children.
  4. Do not approach flammable materials when the exhaust pipe is operating, as its temperature is very high. During installation, use, maintenance, and disposal, ensure no flammable or explosive materials are near the exhaust pipe to prevent ignition and fire.
  5. Maintain proper ventilation and keep all pipes open. When installing, using, maintaining, or disposing of this equipment, ensure a ventilated area to prevent carbon monoxide poisoning. Position the metal exhaust pipe outdoors to prevent exhaust gases from entering the room.
  6. Do not use the heater in an enclosed or unventilated space.
  7. The heater should be turned off when adding diesel.
  8. Do not cut off the power supply directly! After turning off the heating program, the equipment requires a 3-5 minute extinguishing and cooling process. Do not disconnect power during normal operation. Directly cutting power may cause abnormal shutdown, potentially affecting subsequent starts.
  9. If the fuel system is leaking, contact after-sales personnel for repair guidance and parts.
  10. Place the exhaust port outdoors to prevent exhaust gases from entering the room.
  11. During operation, it is strictly forbidden to directly cut off the power supply to stop the heater.
  12. When installing the pipeline, ensure it is unblocked and not squeezed or obstructed.
  13. After overheating protection activates, the machine stops heating. Do not turn off the power. The machine can be restarted once it has cooled down naturally and shut down.
  14. Do not disconnect the power supply immediately after turning off the machine. It takes 3-5 minutes for the machine to stop completely.
  15. The first 3-5 minutes after turning on the machine is the preheating and ignition stage. During this time, the ignition plug, oil pump, and fan operate according to a preset program. Hot air will be discharged from the warm air duct after a few minutes; please be patient.
  16. When starting the heater, the ignition plug requires a relatively large current for heating. An adapter with a voltage of 12V and a current of 12A or greater is needed for power supply. After successful ignition, the equipment typically requires 1-4A to operate continuously.

Important Note: The company is not responsible for any loss or liability caused by failure to install and use the product according to these instructions.

Ignition Point Information: The ignition point of cotton and sponge is 150°C, paper is 130°C, cloth is 270°C, and diesel oil is 220°C. The hot air outlet can reach temperatures higher than 150°C, and the exhaust pipe outlet can exceed 270°C. Exercise extreme caution.

3. Confirmation of Parts List

Before installation, please verify that all components are present and undamaged. The package includes the following items:

Diagram of all included parts for the Hcalory HBH-3S Diesel Air Heater
Diagram showing the host, power adapter, DC wire harness, exhaust silencer, exhaust pipe, intake pipe, air outlet pipe, air filter, vents, manual, fixture accessories set, LCD switch, remote control, controller extension cord, exhaust heat wrap, and 90° welded elbow pipe.
  1. Host
  2. Power Adapter
  3. 12/24V DC Wire Harness
  4. Exhaust Silencer
  5. Exhaust Pipe
  6. Intake Pipe
  7. Air Outlet Pipe
  8. Air Filter
  9. Vents
  10. Manual
  11. Fixture Accessories Set
  12. LCD Switch
  13. Remote Control
  14. Controller Extension Cord
  15. Exhaust Heat Wrap
  16. 90° Welded Elbow Pipe

4. Installation Instructions

The installation of this compact heater is relatively straightforward due to simplified pipeline processes. Primarily, you need to install the exhaust pipe and connect the power adapter or 12/24V DC Wire harness to begin operation. Ensure the exhaust pipe extends outdoors to safely expel combustion exhaust gases.

Installation diagram for the Hcalory HBH-3S Diesel Air Heater
Detailed diagram illustrating the connection of the exhaust pipe, intake pipe, air outlet, and power supply to the main heater unit.

Note: The discharged exhaust gas can reach temperatures as high as 400°C. Keep it away from pets and children. Ensure sufficient clearance from the ground to prevent damage to your floor or lawn.

5. Operating Instructions

5.1 Control Panel Overview

The control panel provides visual feedback and allows for various settings adjustments.

LCD Switch Control Panel layout and icons
The LCD control panel showing display areas for altitude, clock, power bar, data, and parameters, along with buttons for Add, On/Off, Reduce, OK, and Set. Icons indicate fan, sensor failure, power failure, ignition plug, oil pump, Bluetooth, high altitude state, timed alarm, high temperature alarm, fault prompt, automatic start/stop, ventilation state, manual mode, and constant temperature mode.

5.2 Basic Operations

5.2.1 On/Off Operation

  • Start Up: In shutdown state, long press the [On/Off Key] for 2 seconds to start the device.
  • Shutdown: In the on state, long press the [On/Off Key] for 2 seconds. The device will enter a shutdown cooling process and display "OFF". Wait until the machine displays the shutdown status before disconnecting power. Do not force power off during the cooling process to prevent damage.

5.2.2 Manual Mode Operation

Manual mode offers 10 gears (H1-H10), with H10 being maximum power. Press the [Add Key] or [Reduce Key] buttons to adjust gears. The display will show the current gear.

5.2.3 Constant Temperature Mode Operation

  • In constant temperature mode, press [Add Key] or [Reduce Key] to set the temperature value (range: 0-40°C). The display will show the set temperature.
  • Long press the [Set Key] button for 2 seconds to switch between manual and constant temperature mode.

5.2.4 Automatic Start and Stop Operation

When the device is powered on and in constant temperature mode, short-pressing the [On/Off Key] will display the [A] icon, indicating that the automatic start-stop function is enabled. Pressing the key again will make the icon disappear, disabling the function. (Default turn-on: -2°C, turn-off: +3°C. E.g., setting to 24°C will shut down at 27°C and turn on at 22°C).

5.2.5 Ventilation Operation

In shutdown state, hold down the [Set Key] for 2 seconds to open ventilation mode. The display will show the fan icon.

  • Press [Add Key] or [Reduce Key] to adjust fan speed.
  • Long press [Set Key] or [On/Off Key] for 2 seconds to exit ventilation mode.

5.2.6 Switch Startup Display Data

In the on state, short press the [OK Key] to switch display data. The order is: housing temperature → working voltage → ambient temperature → current gear (or current set temperature).

5.2.7 Switch Temperature Units

Hold down the [On/Off Key] + [Add Key] for 2 seconds simultaneously to switch between °C/°F.

5.2.8 Manual Oiling Operation

In shutdown state, press [Add Key] + [Reduce Key] for 2 seconds simultaneously to manually control the oil pump. Release the button to stop pumping oil.

Please use with caution!

5.2.9 Altitude Enabling Operation

Press and hold the [Set Key] + [OK Key] for 2 seconds simultaneously. The [A] icon will display, indicating plateau mode is on and the equipment's air-oil ratio is adjusted for altitude. To turn off, press and hold the same keys again for 2 seconds; the icon will disappear.

5.2.10 Timed On/Off Operation

Hold down [OK Key] + [Reduce Key] for 2 seconds simultaneously. If the timer is off, it will turn on and enter the timing setting interface, displaying the timer symbol. "CLOS" indicates shutdown time, "OPEN" indicates startup time. If the timer is already on, all timers will be turned off, and the symbol will extinguish.

  • Press [Add Key] or [Reduce Key] to adjust the time value (range: 00:00-23:59).
  • Press the [On/Off Key] to switch adjustment digits; the corresponding number will flash.
  • Press the [OK Key] to save the set value. If setting startup time, it will switch to shutdown time setting; otherwise, it exits.
  • After 10 seconds of no key operation, the set value is saved, and the interface exits.

5.2.11 Clock Synchronization Operation

Long press the [OK Key] for 2 seconds to enter the clock adjustment interface, displaying "CLOC".

  • Press [Add Key] or [Reduce Key] to adjust the time value (range: 00:00-23:59).
  • Press the [On/Off Key] to switch adjustment digital position; the corresponding number will flash.
  • Press the [OK Key] button to confirm the time and enter week setting.
  • Press [Set Key] to enter Settings Week.
  • Exit the clock adjustment interface after 10 seconds of no key operation.

5.2.12 Set Week Operation

The digital display shows "EE-1".

  • Press [Add Key] or [Reduce Key] to adjust the tail number.
  • Press the [OK Key] button to confirm and exit the clock adjustment interface.
  • Press the [Set Key], or press the button for 10 seconds to exit the clock adjustment interface.

When the APP opens the Bluetooth connection, it automatically synchronizes the phone time.

5.2.13 Match Wireless Remote Control Operation

In shutdown state, press [On/Off Key] + [Reduce Key] simultaneously for 2 seconds to display "HFA1".

  • Press [Add Key] or [Reduce Key] to adjust the fourth digit (Remote ID: 1-4, corresponding to 4 remote controls).
  • Select the remote control number, then press the remote control button to code. It will exit the code state after success.
  • Press the [Set Key] to exit remote pairing mode.

Remote control requirements: frequency band 433MHz, 24-bit code.

5.2.14 Screen Brightness Adjustment

In the on state, long press [Add Key] + [Reduce Key] for 2 seconds simultaneously. The "AIRHEATER" English letter icon in the upper left corner will flash. Adjust brightness by clicking [Add Key] or [Reduce Key]. After adjustment, long press [Add Key] + [Reduce Key] for 2 seconds again to confirm. Brightness is also confirmed after 10 seconds of inactivity.

5.2.15 Check Bluetooth Password

Press [OK Key] + [Add Key] simultaneously. The screen displays a 4-digit Bluetooth connection password (initial password is "0000").

5.2.16 Bluetooth Password Initialization

In shutdown state, press [OK Key] + [On/Off Key] for 2 seconds simultaneously to enter password input state. The password is "3333".

  • Press [Add Key] or [Reduce Key] to adjust the number.
  • Press the [On/Off Key] to switch adjustment digits; the corresponding number will flash.
  • Press the [OK Key] button to confirm Bluetooth password initialization.
  • Press [Set Key] to cancel the operation.

5.2.17 Frequency Adjustment of Oil Pump (Use with Caution)

In shutdown state, press [OK Key] + [Set Key] for 2 seconds simultaneously to enter password input state. The password is "3638".

After entering the password, "1-2.0" is displayed, meaning the frequency of the 1st oil pump is 2.0 (the 10th oil pump is replaced by A).

  • Press [Add Key] or [Reduce Key] to increase or decrease oil pump frequency.
  • Press the [On/Off Key] to switch oil pump gear.
  • Press [OK Key] to confirm the operation.
  • Press [Set Key] to cancel the operation.

5.2.18 Frequency Initialization of Oil Pump

In shutdown state, press [OK Key] + [On/Off Key] for 2 seconds simultaneously to enter password input state. The password is "6666".

6. Instructions for App Operation

If your heater version includes Bluetooth, you can control it via the Hcalory app. If unsure about Bluetooth compatibility, contact customer service.

6.1 How to Download the App

Android users can download the installation package from the Google Play Store. Apple users can download from the App Store or scan the provided QR codes.

QR code for Android App download
QR Code for Android App
QR code for iOS App download
QR Code for iOS App

6.2 App Usage

  1. Adding a Device: Upon first opening the app, click the "+" sign to add your heater.
  2. Bluetooth Authorization: When searching for devices, ensure Bluetooth is enabled and grant precise positioning authorization. Refusing authorization may prevent the app from finding nearby devices.
  3. Bluetooth Connection: Before connecting, allow the Hcalory app to discover and connect to nearby devices.
  4. Device Selection: If the Bluetooth interface doesn't pop up, click the Bluetooth icon in the app to search for nearby devices. Select the device with "hcalory" in its name. If your phone is already connected, other phones cannot connect until the current connection is exited.
  5. Identifying Devices: While the device is in standby mode, press the "OK" key on the control panel to display a 4-digit number. This helps distinguish between multiple heaters when connecting via the app.
  6. Operations after Connection: Once successfully connected, the app allows various operations:
    • Start Heating: Click the heating button to activate regular heating mode. Choose between temperature mode (intelligent gear control based on set temperature) or gear mode (fixed gear operation). Temperature mode is ideal for indoors, while gear mode suits open areas or poorly insulated tents.
    • Fan Mode: In fan mode, the fan operates independently without combustion, functioning as a fan or exhaust fan.
    • Plateau Mode: For high-altitude areas (2000-5000m), enable plateau mode. The device simulates high-altitude conditions and adjusts the oil pump frequency to maintain stable combustion. (Not recommended for prolonged use above 4000m without spare parts due to environmental complexities).
    • Scheduled Timing: Set multiple timers for on/off functions. Ensure the heater remains powered on for timed functions to execute.
    • Other Settings: Adjust language, temperature units, and provide feedback via the app.

7. Maintenance

7.1 One-Touch Carbon Clean

Long-term operation in low-oxygen environments can lead to carbon deposits in the combustion chamber, reducing efficiency, causing ignition failures, black smoke, and increased fuel consumption. The HBH-3S features a one-touch carbon clean function.

Built-in maintenance mode for carbon cleaning
The heater's built-in maintenance mode allows for one-click carbon cleaning to reduce wear and extend lifespan. Carbon buildup occurs from short runtimes, low-power operation, and high-altitude use, leading to slow ignition and black exhaust. Regular maintenance in a ventilated area extends service life.

Operation: In standby mode, press and hold the [Set Key] + [Reduce Key] for 2 seconds until the screen displays "CLEA" and the Max icon flashes. A 20-minute self-cleaning cycle will automatically start and stop.

Recommendation: Perform carbon cleaning every 1-2 weeks if used at high altitudes (>1,000m), for long periods at low gears, or if symptoms like slow ignition or black exhaust occur. To cancel mid-cycle, press and hold the [On/Off Key] to power off.

7.2 General Maintenance Tips

  • Regularly check the air filter for cleanliness and replace if necessary.
  • Ensure all connections (fuel lines, electrical wires, exhaust pipes) are secure and free from damage or blockages.
  • Keep the heater's exterior clean and free from debris.
  • Store the heater in a dry, protected environment when not in use.

8. Troubleshooting (Fault List)

If the digital display shows an error code (e.g., "E-21"), refer to the table below for the fault cause and method of disposition. The fault symbol and corresponding faulty device icon will flash.

Fault CodeFailure CauseMethod of Disposition
E021The power supply voltage is too low1) Check whether the battery connection wire is damaged and whether the plug is secure.
2) Check whether the fuse is aging.
E022The power supply voltage is too highThe power supply voltage is too high. Check the battery output voltage range.
E023Abnormal power supply voltageThe power supply voltage is abnormal. Check the battery output voltage range.
E031The ignition plug is open1) Check whether the ignition plug connection wire and plug are loose or broken.
2) Check whether the ignition plug connection plug is loose.
3) Give the ignition plug a separate power connection to check whether it is damaged.
E032The ignition plug is short circuit1) Check whether the ignition plug connection wire is short circuit.
2) Ignition plug is damaged or the motherboard reads wrong.
E041The oil pump is open1) Check whether the connecting wires and connectors of the oil pump are damaged, loose or broken.
2) Check whether the oil pump is damaged.
E042Oil pump short circuit1) Check whether the connection line of the oil pump is short circuit.
2) Check whether the oil pump is blocked and damaged.
E05High temperature alarm (case > 230°C)1) Check whether the cold air intake is blocked.
2) Check whether the hot air outlet pipe is bent or blocked.
3) Check whether the fan is running normally.
4) Check whether the sensor is damaged.
E061Motor open circuit1) Check whether the motor connection wire is broken.
2) Check whether the motor connection wire plug is loose.
3) Connect the motor to the power supply separately and check whether it rotates.
E062Motor short circuit1) Check whether the connecting wire of the motor is short circuit.
2) Motor damage or motherboard read error.
E063Fan speed is abnormal1) Check whether the impeller is stuck.
2) The gap between the magnet on the wind wheel and the Hall sensor on the controller is too large.
E07The master board communicates abnormally with the remote control switchboard1) Check whether the connection port of the remote control switch is loose.
2) Check whether the connection line (blue) of the remote control switch is broken.
E08Flameout1) Check for oil shortage, low temperature solidification of oil, oil line blockage, oil pipe folding, or too many steam drums in the oil pipe, and oil pump jam.
2) Check whether the oxygen intake and exhaust air duct is smooth.
3) Check whether the housing temperature sensor is in full contact with the housing and whether the pressure spring is strong.
4) Check whether the sensor is damaged.
E091The temperature sensor is open1) Check whether the temperature sensor connection wire and plug are damaged or loose.
2) Check whether the sensor is damaged.
E092The temperature sensor is short circuit1) Check whether the temperature sensor connection line is short circuit.
2) Check whether the sensor is damaged.
E10The startup was unsuccessful1) The housing temperature is too high, and the housing cannot be cooled after 3 minutes of starting.
2) There is a lot of white smoke at the exhaust port: Check if the filter screen next to the ignition plug is clean (clean or replace if not), check if the oil pump is spraying fuel effectively, check if the ignition plug is aging.
3) There is a small amount of white smoke or no smoke in the waste gas: Check if oil is missing, if the oil line is frozen or blocked, if the oil pump is stuck or damaged, if combustion intake and exhaust channels are smooth, if the ignition plug is damaged, if the gap of the inner wind wheel is too large.
4) Ignition is normal but still reports ignition failure fault: Check if the housing temperature sensor is in full contact with the housing and if the pressure spring is strong, and if the sensor is normal.

9. Specifications

AttributeValue
Brand NameHcalory
Model NameHBH-3S
Peak Power8KW
Diesel Consumption0.12 L/h ~ 0.51 L/h
Operating Voltage12V DC / 24V DC / 220~240V AC
MaterialMetal and Plastic
Fuel Tank Capacity5L
Fuel TypeDiesel
Product Packaging Dimensions43 × 29 × 41 cm
Item Length43cm
Item Width29cm
Item Height41cm
Item Weight9.5kg
External Testing CertificationCE
CertificationCE, RoHS, FCC
Operating Temperature40℃ ~ 40℃ (40℉ ~ 104℉)
Auto Start / StopSupported
Bluetooth APP ControlSupported
Remote ControlSupported (up to 30m)
LCD Panel ControlSupported
Automatic Altitude Adaptation Mode1000M ~ 5000M
Heating Area20~25㎡
Switch TypeLCD Switch
Item TypeHeating & Fans
OriginMainland China

10. User Tips

  • Initial Check: Before first use, especially if the unit does not fire, check the exhaust for any blockages (e.g., casting slag) that might prevent proper operation.
  • Pump Noise: While the pump is designed for quiet operation, some noise is normal, especially under full load.
  • App Connectivity: The Bluetooth app signal may not always be stable; the radio remote control generally offers more consistent connectivity.
  • Exhaust Safety: Always ensure the exhaust is routed completely outdoors to prevent fumes from entering living spaces.

11. Warranty and Support

11.1 Contact Us

Thank you for your support and trust in Hcalory products. Parking heater structures can be complex, and various outdoor or indoor environments may present unexpected situations. If you encounter difficulties that you cannot resolve, please contact us for guidance on adjustments or repairs.

For after-sales technical support or any questions about Hcalory's products, you can send an email to hcalory@hcalory.com or contact our after-sales personnel through the sales platform where you purchased the product. We will provide you with detailed instructions or operational videos. Your feedback and support are greatly appreciated.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.