PowMr POW-HVM2.5KW-12V

Contents

PowMr 2500W Hybrid Solar Inverter

Model: POW-HVM2.5KW-12V

User Manual

1. Introduction

1.1. About This Manual

This manual introduces the assembly, installation, operation, and troubleshooting of the PowMr 2500W Hybrid Solar Inverter. Please read this manual carefully before installation and operation to ensure proper use and safety.

1.2. Product Overview

The PowMr 2500W Hybrid Solar Inverter (POW-HVM2.5KW-12V) is an all-in-one unit integrating an MPPT solar charge controller, a high-frequency pure sine wave inverter, and a UPS (Uninterruptible Power Supply) function module. Its high-frequency transformer design allows for compact size and efficient power conversion. It supports dual inputs from photovoltaic panels and AC/generator power, capable of charging batteries while simultaneously supplying AC loads. It is compatible with both lead-acid and lithium batteries (with BMS communication). Optional accessory modules enable remote monitoring. This inverter is ideal for off-grid power supply in areas without grid access, as a home backup power source, and for self-consumption photovoltaic systems.

1.3. Features

  • Pure sine wave output inverter.
  • Selectable input voltage range for utility grid based on load requirements (household appliances/personal computers).
  • Adjustable charging current via LCD based on battery requirements.
  • Simultaneous power supply to loads from solar energy and utility grid.
  • AC input compatible with mains and generator.
  • Automatic restart function upon restoration of mains power.
  • Overload, over-temperature, and short circuit protection.
  • Intelligent charging design for optimal battery utilization.
  • RS485 port for BMS communication.
  • Cold start function.
  • Intelligent fan speed adjustment based on temperature, load, and charging current.
  • Built-in MPPT with an operating voltage range of 55V~430V and open circuit voltage of 450Voc.
  • WIFI remote monitoring (optional).

1.4. Basic System Architecture

The inverter/charger forms the core of a hybrid power system. A complete running system typically includes:

  • Solar Power (PV array)
  • Generator or Mains Electricity (Utility Grid)
  • External Battery Packs (12V Lithium or Lead-Acid Battery)
  • Home Appliances (Loads)

The inverter can power various appliances in home or office environments, including motor-type appliances like tube lights, fans, refrigerators, and air conditioners.

Hybrid Power System Diagram
Figure 1: Hybrid Power System Diagram. Shows solar power, generator/utility, and battery inputs connected to the solar inverter, which then powers home appliances.

2. Safety Regulations

WARNING: This article contains important safety and operation instructions. Please read and save this manual for future reference.

  1. Choose the corresponding setting for lead-acid or lithium batteries. Incorrect settings may lead to system malfunction.
  2. Before using the unit, read all instructions and cautionary notes on the unit and understand all battery models and relevant chapters in this manual.
  3. Never short-circuit AC output and DC input. Never connect the mains when the DC input is short-circuited.
  4. Never charge a non-rechargeable battery.
  5. Do not disassemble the unit. For maintenance or repair, send it to a professional technical service center. Incorrect reassembly may lead to electric shock or fire.
  6. To reduce the risk of electric shock, disconnect all wiring before attempting any maintenance or cleaning. Turning off the device alone will not eliminate this risk.
  7. Exercise extreme caution when using metal tools on or around the battery. Sparks from falling tools can cause short circuits, potentially leading to explosions.
  8. For optimal operation, select appropriate cable sizes for battery connection as per instructions.
  9. When disconnecting AC or DC terminals, strictly follow the installation procedure detailed in the "Installation" section.
  10. This off-grid solar inverter must be connected to a permanent grounding wiring system. Comply with local requirements and regulations.
  11. Provide a fuse that meets specific battery power supply requirements for overcurrent protection.
  12. WARNING: Only professional service personnel can repair this equipment. If errors persist after troubleshooting, return the inverter to the local dealer or service center.

3. Installation

3.1. Unpacking and Inspection

Unpack the inverter and inspect for any damaged objects. The package should contain:

  • Inverter Unit x 1
  • User Manual x 1

3.2. Preparation Before Installation

Before connecting any wiring, remove the bottom port cover by unscrewing the two screws as shown in the wiring guide video.

Video: Wiring Guide for PowMr All-in-one Solar Inverter. This video demonstrates the steps for wiring the inverter, including removing the port cover, grounding, and connecting utility power, load wires, battery, and PV array.

3.3. Installation Location

Consider the following points when selecting an installation location:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install the inverter at eye level for easy reading of the LCD display.
  • Allow approximately 20 cm clearance on both sides and above the equipment, and 50 cm below, for proper air circulation and heat dissipation.
  • The ambient temperature should be between 0°C and 55°C for optimal operation.
  • The recommended installation position is vertically adhered to the wall.
  • Ensure sufficient space around the machine for adequate heat dissipation and wire removal.

CAUTION: Suitable for installation on concrete or other non-combustible surfaces only.

Tighten the screws to fix the installation. M4 or M5 screws are recommended for machine fixing.

3.4. Wiring Connections

Ensure all wiring is performed by qualified personnel and adheres to safety regulations.

3.4.1. Grounding

Ground the inverter via the bottom grounding terminal. This off-grid solar inverter must be connected to a permanent grounding wiring system. Comply with local requirements and regulations.

3.4.2. Battery Connection

WARNING: Install an independent DC overcurrent protector or disconnect device between the battery and the inverter. All wiring must be performed by qualified personnel. Use appropriate cable for battery connection to reduce risk of injury.

Recommended battery cable specifications:

Model Wire Specification Torque Value
2.5KVA-12V 1 * 4 AWG (22mm²) 2-3 Nm

Note: The recommended charging current for lead-acid batteries is 0.2C (C is battery capacity).

Steps for battery connection:

  1. Connect the battery according to the recommended cable specifications.
  2. Connect all battery packs as needed.
  3. Insert the ring terminal of the battery cable into the inverter's battery connector. Ensure bolts are tightened with a torque of 2-3 Nm. Verify correct polarity and tighten the ring terminal with the battery terminal.

WARNING: Shock Hazard. Installation must be performed with care due to high battery voltage in series.
CAUTION: Do not place anything between the flat part of the inverter terminal and the ring terminal, as this may cause short circuit or overheating.
CAUTION: Do not apply antioxidant to the terminal before it is tightly connected.
CAUTION: Before making the final DC connection or closing the DC breaker/disconnector, ensure positive (+) is connected to positive (+) and negative (-) to negative (-).

Connect battery packs as shown in the diagram:

Battery Connection Diagram
Diagram showing battery connections for 2.5KVA/12V and 3.5KVA/24V inverters.

3.4.3. Lithium Battery Communication

If using a lithium battery, only those matched with BMS communication protocol are allowed. Connect the RJ45 communication cable between the inverter and battery. Confirm the lithium battery BMS port's PIN corresponds with the inverter BMS communication port.

Inverter BMS port PIN definition:

Pin Number Port Definitions
1RS485B
2RS485A
3NG
4NG
5NG
6NG
7RS485A
8RS485B

NOTE: If you choose a lithium battery, connect the battery and inverter with a BMS communication cable and select the battery type as "LIB-485" mode in Program 05.

3.4.4. AC Input/Output Connection

CAUTION: Install a separate AC breaker between the inverter and AC input power source for secure disconnection and overcurrent protection. Do NOT mis-connect input and output connectors. All wiring must be performed by qualified personnel. Use appropriate cable sizes.

Suitable cable specifications for AC wires:

Model Wire Gauge Torque Value
2.5KVA-12V 1 * 12 AWG 1.2-1.6 Nm

Steps for AC input/output connection:

  1. Before making AC input/output connections, open the DC protector or disconnector first.
  2. Remove 10mm of insulation sleeve for six conductors. Shorten phase L and neutral conductor N by 3mm.
  3. Insert AC input wires according to polarities indicated on the terminal block and tighten the terminal screws. (L→ LINE (brown or black), N→ Neutral (blue))
  4. Insert the AC output conductor according to the polarity identification at the terminal and tighten the screw.
  5. Ensure the wires are firmly connected.

WARNING: Be sure that the AC power source is disconnected before attempting to hardwire it to the unit.

CAUTION: Ensure all AC cables are connected correctly according to the corresponding polarity. Appliances like air conditioners require 2-3 minutes to restart. If a power shortage occurs, it may damage connected appliances. Check the air conditioner manufacturer for time-delay functions. Otherwise, the inverter may trigger an overload fault to protect the appliance, but internal damage may still occur.

3.4.5. PV Connection

CAUTION: Before connecting the PV module, install a separate DC circuit breaker between the inverter and PV module. All wiring must be performed by qualified personnel. Use appropriate cable sizes.

Suitable cable specifications for PV module connection:

Model Wire Gauge Torque Value
2.5KVA-12V 1 * 14 AWG 1.2-1.6 Nm

PV Module Selection considerations:

  1. Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter (500Vdc).
  2. Open circuit Voltage (Voc) of PV modules should be higher than the min. battery voltage.

Recommended module configurations (example for 250Wp PV module):

Solar Panel Parameters Solar Input Range (Min in serial: 6 pcs, max in serial: 11 pcs) Q'ty of Panels Total Input
250Wp, Vmp: 30.1Vdc, Imp: 8.3A, Voc: 37.7Vdc, Isc: 8.4A, Cells: 603 pcs in serial3750W
4 pcs in serial41000W
5 pcs in serial51250W
6 pcs in serial61500W
8 pcs in serial82000W
11 pcs in serial112750W

Steps for PV module connection:

  1. Remove 10mm of insulation sleeve for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors. Connect positive pole (+) of connection cable to positive pole (+) of PV input connector. Connect negative pole (-) of connection cable to negative pole (-) of PV input connector.
  3. Make sure the wires are securely connected.

3.5. Final Assembly

After connecting all the wires, replace the bottom port cover and secure it with the screws.

4. Operation

4.1. Power On/Off

After correctly installing the machine and connecting the battery, simply press the On/Off switch to turn on the machine.

Front view of PowMr Solar Inverter Charger
Front view of the PowMr Solar Inverter Charger, showing the LCD display and control buttons.

4.2. Operation and Display

The operation and display panel is located on the front of the inverter. It includes four function keys and an LCD screen for indicating operation status and input/output power information.

4.2.1. Function Keys

Function Key Description
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

4.2.2. LED Indicators

Indicator LED Status Messages
AC/INVGreen, Solid OnOutput is powered by utility in Line mode.
Green, FlashingOutput is powered by battery or PV in battery mode.
CHGGreen, Solid OnBattery is fully charged.
Green, FlashingBattery is charging.
FAULTRed, Solid OnFault occurs in the inverter.
Red, FlashingWarning condition occurs in the inverter.

4.2.3. LCD Display Icons

The LCD display provides various information through icons. Here are some key icons and their descriptions:

Icon Function Description
ACIndicates the AC input.
PVIndicates the PV input.
INPUTBATT (e.g., 888 kW/VA/Hz/°C)Indicates input voltage, input frequency, PV voltage, battery voltage, and charger current.
88Indicates the setting programs.
88 (flashing)Flashing with warning code.
88 (lit)Lighting with fault code.
OUTPUTBATTLOAD (e.g., 8.88 kW/VA/Hz)Indicates output voltage, output frequency, load percent, load in VA, load in Watt, and discharging current.
Battery Information (bars)Indicates battery level by 0-24%, 25-49%, 50-74%, and 75-100% in battery mode and charging status in line mode.
OVER LOADIndicates overload.

4.2.4. Operating Mode Description

The inverter operates in various modes, each with specific power flow and charging behavior:

Operation Mode Description
Standby Mode / Power Saving ModeNo output is supplied by the unit, but it can still charge batteries. In power saving mode, output is off if load is very low.
Line ModeThe unit provides output power from the mains and can charge the battery. Solar and mains can supply power to loads simultaneously.
Battery ModeThe unit provides output power from battery and PV power. Battery and solar can supply power to loads simultaneously.

5. LCD Settings

To enter setting mode, press and hold the "ENTER" button for 3 seconds. Use "UP" or "DOWN" to select programs, then "ENTER" to confirm or "ESC" to exit.

Key settings include:

  • Program 00: Exit Setting Mode (Escape, One-button restore setting options)
  • Program 01: Output Source Priority (SUB priority, SBU priority, MKS priority)
  • Program 02: Maximum Charging Current (10A, 20A, 30A, 40A, 50A, 60A, 70A, 80A, 90A, 100A)
  • Program 03: AC Input Voltage Range (Appliances (90-280VAC), UPS (170-280VAC))
  • Program 04: Power Saving Mode Enable/Disable
  • Program 05: Battery Type (AGM, Flooded, User-Defined, LIB-485)
  • Program 06: Auto Restart When Overload Occurs
  • Program 07: Auto Restart When Over Temperature Occurs
  • Program 09: Output Frequency (50Hz, 60Hz)
  • Program 10: Output Voltage (220V, 230V, 240V)
  • Program 11: Maximum Utility Charging Current (10A to 100A)
  • Program 12: Setting Voltage Point Back to Utility Source (for SBU priority, various voltage options)
  • Program 13: Setting Voltage Point Back to Battery Mode (for SBU priority, various voltage options)
  • Program 16: Charger Source Priority (Solar first, Solar and Utility, Only Solar)
  • Program 18: Alarm Control (Alarm on/off)
  • Program 19: Auto Return to Default Display Screen (Enable/Disable)
  • Program 20: Backlight Control (On/Off)
  • Program 22: Beeps While Primary Source Is Interrupted (On/Off)
  • Program 23: Overload Bypass (Enable/Disable)
  • Program 25: Record Fault Code (Enable/Disable)
  • Program 26: Bulk Charging Voltage (C.V voltage)
  • Program 27: Floating Charging Voltage
  • Program 29: Low DC Cut-off Voltage
  • Program 30: Battery Equalization (Enable/Disable)
  • Program 31: Battery Equalization Voltage
  • Program 33: Battery Equalized Time
  • Program 34: Battery Equalized Timeout
  • Program 35: Equalization Interval
  • Program 36: Equalization Activated Immediately
  • Program 37: GRID-tie Operation (Off grid, Hybrid)
  • Program 38: GRID-tie Current
  • Program 39: LED Pattern Light (On/Off)
  • Program 43: Lithium Battery Protocol (PYLON, PACE)

6. Battery Management

6.1. Battery Equalization

The equalization function helps reverse the buildup of negative chemical effects like stratification and removes sulfate crystals from battery plates, extending battery life. It is recommended to equalize batteries periodically.

To apply equalization:

  1. Enable battery equalization in LCD setting program 30.
  2. Apply by either: setting the equalization interval in program 35, or activating equalization immediately in program 36.

When the setting equalization interval is reached, or equalization is active immediately, the controller will enter the Equalize stage. The controller will charge the battery until it reaches the equalization voltage, then maintain it until the set equalized time is reached. If the battery voltage doesn't rise to the equalization voltage within the set time, the charge controller will extend the time until it does. If it still doesn't reach the voltage after the extended time, the controller will stop equalization and return to the float stage.

Battery Equalization Charging Curve
Diagram illustrating the battery equalization charging curve, showing Bulk, Absorption, Float, and Equalize stages.

6.2. Mains and Lithium Battery Activation Function

  1. After 90 seconds of mains power connection to the inverter, the machine connects to the mains and starts operation.
  2. If the inverter is in lithium battery mode (Program 05 is LIB or LIB-485) and the mains is connected but the battery is not, the mains activation function is automatically enabled.

7. Clearance and Maintenance for Anti-Dust Kit

7.1. Overview

Every inverter comes with an anti-dust kit installed from the factory. The inverter automatically detects this kit and activates an internal thermal sensor to adjust internal temperature. This kit prevents dust from entering the inverter, increasing product reliability in harsh environments.

7.2. Clearance and Maintenance Steps

  1. Remove the screws securing the bottom port cover.
  2. Carefully remove the dustproof case and take out the air filter foam.
  3. Clean the air filter foam and dustproof case.
  4. After cleaning, re-assemble the dust-kit back into the inverter.

NOTICE: The anti-dust kit should be cleaned from dust every one month.

8. Troubleshooting

8.1. Fault Codes

The inverter displays fault codes to indicate specific issues:

Fault Code Fault Event
01Fan is locked when the inverter is turned off.
02Over temperature
03Battery voltage is too high
04Battery voltage is too low
05Output short circuit or over temperature.
06Output voltage is too high
07Exceeding overload time
08BUS voltage is too high
09BUS soft start failed.
13PV voltage is too high
51Over current and surge
52BUS voltage is too low
53Inverter soft start failed.
55Over DC voltage in AC output
56Battery is disconnected
57Current sensor failed.
58Output voltage is too low
61Communication Failure

8.2. Warning Codes

The inverter displays warning codes to indicate potential issues:

Warning Code Warning Event Automatic Alarm
01Fan is locked when inverter is on.Beep three times every second
03Battery overchargeBeep once every second
04Battery low voltageBeep once every second
07OverloadBeep once every 0.5 second
10Output power is deratingBeep twice every 3 seconds
15PV energy is weakNo Beep
EQBattery equalizationNo Beep
bPBattery is not connected.No Beep

8.3. Common Problems and Solutions

Problem Explanation / Possible Cause What to Do
Unit shuts down automatically during startup process. Battery voltage is too low 1. Re-charge battery.
2. Replace battery.
No response after power on. 1. The battery voltage is far too low.
2. Battery polarity is connected reversed.
1. Check if batteries and the wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Input protector is tripped Check if AC breaker is tripped and AC wiring is connected well.
Mains exist but the unit works in battery mode. Insufficient quality of AC power. (Shore or Generator) 1. Check if AC wires are too thin and/or too long.
2. Check if generator (if applied) is working well or if input voltage range setting is correct.
Buzzer beeps continuously and the status indicator icon is always on. Overload error. The inverter is overload 110% and time is up. Reduce the connected load by switching off some equipment.
Output short circuited. Check if wiring is connected well and remove abnormal load.
Internal temperature of inverter component are over heated. Check whether the air flow of the unit is blocked or whether the ambient temperature is too high. Return to repair center.
Battery is over-charged. Check if spec and quantity of batteries are meet requirements.
Fan fault Replace the fan.
Output abnormal 1. Reduce the connected load.
2. Return to repair center.
Internal components failed. Return to repair center.
Over current or surge.
Bus voltage is too low.
Output voltage is unbalanced.
Restart the unit, if the error happens again, please return to repair center.

9. Specifications

9.1. Line Mode Specification

Parameter Value (2.5KVA-12V)
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS); 90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS); 100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionBattery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

Output power derating: When AC input voltage drops to 95V or 170V depending on models, the output power will be derated.

9.2. Inverter Mode Specification

Parameter Value (2.5KVA-12V)
Rated Output Power1600VA/1600W
PV + Battery Rated Output Power2500VA/2500W
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency60Hz or 50Hz
Peak Efficiency92%
Overload Protection3s@≥150% load; 20s@110%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage12Vdc
Cold Start Voltage11.3Vdc
Low DC Warning Voltage (<50% Load)11.0Vdc
Low DC Warning Voltage (≥50% Load)10.5Vdc
Low DC Warning Return Voltage (<50% Load)11.5Vdc
Low DC Warning Return Voltage (≥50% Load)11.0Vdc
Low DC Cut-off Voltage (<50% Load)10.2Vdc
Low DC Cut-off Voltage (≥50% Load)10Vdc
High DC Recovery Voltage16Vdc
High DC Cut-off Voltage15Vdc
No Load Power Consumption<25W
Saving Mode Power Consumption<20W

9.3. Charging Mode Specification

Parameter Value (2.5KVA-12V)
Utility Charging Mode Current (UPS @Nominal Input Voltage)100A
Bulk Charging Voltage (Flooded Battery)14.6V
Bulk Charging Voltage (AGM / Gel Battery)14.1V
Floating Charging Voltage13.5Vdc
Charging Algorithm3-Step
Solar Charging Mode Rated Power3000W
Solar Charging Mode Rated Solar Voltage240V
Solar Charging Mode PV Array MPPT Voltage Range55V~450V
Solar Charging Mode Max. PV Array Open Circuit Voltage500V
Solar Charging Mode IMax.PV13A
Solar Charging Mode Max Charging Current100A

9.4. General Specifications

Parameter Value
Dimensions (D*W*H)345 * 255 * 100 mm
Net Weight4.6 kg
Operating Temperature Range0°C to 55°C
Storage Temperature-15°C to 60°C
Operating Altitude≤ 6000 m
Battery Overvoltage ProtectionYes
Overload ProtectionYes
Output Short-Circuit ProtectionYes
Over-Temperature ProtectionYes

10. User Tips

  • Always ensure proper ventilation around the inverter to prevent overheating, especially during high load operation.
  • Regularly check all wiring connections for tightness and signs of wear to maintain optimal performance and safety.
  • If using lithium batteries, ensure the BMS communication is correctly configured to prevent potential issues and maximize battery life.
  • Monitor the LCD display for any fault or warning codes and refer to the troubleshooting section promptly to address issues.
  • Consider the environmental conditions (temperature, dust) and perform routine maintenance on the anti-dust kit to prolong the inverter's lifespan.

11. Warranty and Support

For technical support, warranty claims, or any inquiries, please contact:

SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD
Tel/Fax: +86 755-28219903
Email: support@powmr.com
Web: www.powmr.com
Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.