Introduction
The TUNGFULL Automatic Screw Feeder Machine is designed to enhance efficiency in assembly operations by automatically sorting and dispensing screws. This manual provides essential information for the safe and effective setup, operation, and maintenance of your screw feeder.
It is suitable for a wide range of applications, including electronic product assembly, mobile phone and computer production lines, hardware assembly, and industrial automated production. The machine supports M1-M5 screws with a length of less than 20mm, including various head types such as round head, flat head, screw with gasket, self-tapping, half countersunk head, and countersunk screws.
Video: Demonstration of the automatic screw feeder in operation, showing screws being dispensed and picked up by a screwdriver.
Image: The TUNGFULL S-1050P Automatic Screw Feeder, designed for precision screw dispensing, shown with examples of compatible screws.
⚠️ WARNING
- Do not perform maintenance or adjustments while the device is powered on.
- Do not put your hands inside the vibratory feeder.
- Do not use the device beyond its specified screw size range.
- Avoid liquid entering the device.
- Ensure voltage compatibility before use.
- Do not disassemble the outer casing while the device is running.
Setup Instructions
- Placement: Place the equipment on a stable workbench. Ensure the base is secure to prevent vibration and displacement during operation.
- Power Connection: Before connecting to a power source, verify that the voltage of your power supply is compatible with the device's requirements (DC 15V1.5A).
- Track Width Adjustment: Adjust the track width according to the specifications of the screws you intend to use. This ensures smooth feeding and prevents jamming.
- Screw Loading: Add an appropriate number of screws to the storage bin (screw feeding silo).
Image: External view of the S-1050 model with labels for key components, including the screw feeding silo and various adjustment points.
Image: Internal view of the screw feeder with labels for key components, such as the feeding wheel and guide rail.
Operating Instructions
The TUNGFULL Automatic Screw Feeder is designed for simple, one-button start operation, providing automatic feeding and stable conveying of screws.
Adjustments:
- Track Door Adjustment: Fine-tune the opening of the track door to control screw flow.
- Guide Groove Adjustment: Adjust the front and rear, up and down, and left and right positions of the guide groove for optimal screw alignment.
- Track Side Door Adjustment: Adjust the side door of the track to accommodate different screw head sizes.
- Feeding Wheel Delay Adjustment: Control the delay of the feeding wheel to synchronize with your assembly process.
- Guide Rail Vibration Delay Adjustment: Adjust the vibration delay of the guide rail for consistent screw presentation.
- Motor Vibration Speed Adjustment: Regulate the motor's vibration speed to match the required output rate.
Image: Control panel with knobs for 'SPEED', 'VIBRATOR', and 'ROLLER' adjustments, allowing for customizable transmission rate.
Digital Display (S-1060 Model Only):
The S-1060 model features a digital display to count dispensed screws. Use the 'Up' and 'Down' buttons to navigate and the 'Set' button to confirm settings or reset the count.
Image: The S-1060 model features a digital display for screw counting, with 'Up' and 'Down' buttons and a 'Set' button for configuration.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your screw feeder. Always ensure the device is powered off and unplugged before performing any maintenance.
- Cleaning: Periodically clean the screw feeding silo and guide rails to prevent accumulation of debris or screw fragments that could cause jamming.
- Inspection: Regularly inspect the feeding wheel, brushes, and guide rails for wear and tear. Replace components as necessary.
- Lubrication: Apply appropriate lubricant to moving parts as recommended by the manufacturer (if applicable, not specified in provided data).
Image: Illustration of the brush adjustment mechanism, ensuring smooth screw discharge. Ensure brushes are clean and in good condition.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Screws not feeding smoothly or jamming | Incorrect track width adjustment, debris in guide rails, incorrect screw size/type, insufficient screws in silo. | Adjust track width to match screw specifications. Clean guide rails and silo. Ensure correct screw size (M1-M5, length < 20mm). Refill screw silo. |
| Machine not powering on | Power cable disconnected, power switch off, incorrect voltage. | Check power cable connection. Ensure power switch is in 'ON' position. Verify power supply voltage matches device requirements (DC 15V1.5A). |
| Inconsistent screw presentation | Improper vibration settings, unstable workbench. | Adjust motor vibration speed and guide rail vibration delay. Ensure the machine is placed on a stable, level surface. |
Specifications
| Feature | S-1050P (No Digital Display) | S-1060 (With Digital Display) |
|---|---|---|
| Output Speed | 2 pieces/second | 2 pieces/second |
| Output Voltage | DC 15V1.5A | DC 15V1.5A |
| Screw Capacity | 500CC | 500CC |
| Screwdriver Diameter | 1-5MM | 1-5MM |
| Screw Length | Less than 20MM | Less than 20MM |
| Weight | 2.5KG | 2.75KG |
| Dimensions (Approx.) | Overall: 265mm (L) x 165mm (W) x 185mm (H) | |
| Applicable Screw Diameter (d) | M1-M5 | |
| Applicable Screw Length (L) | ≤ 20mm | |
| Compatibility | Screws with nuts | |
Image: Visual comparison of the S-1050P (Basic Style Without digital display) and S-1060 (With digital display) models, highlighting their key differences in features and specifications.
Image: Comprehensive dimensions of the screw feeder from multiple views.
Image: Diagram detailing applicable screw dimensions: diameter (d) M1-M5, length (L) ≤ 20mm, and compatibility with screws that have nuts.
User Tips
- For optimal performance, regularly clean the screw feeding silo and guide rails to prevent screw jamming.
- Always ensure that the screws used are within the specified diameter (M1-M5) and length (less than 20mm) range for smooth operation.
- Experiment with the 'SPEED', 'VIBRATOR', and 'ROLLER' adjustment knobs to find the ideal settings for different screw types and materials to achieve consistent feeding.
- When switching between different screw sizes, remember to adjust the track width accordingly to prevent misfeeds.
Warranty & Support
Manufacturer Information:
ShenZhen Tungfull Digital Technology Co., Ltd
Address: A302, Building 25, Hong ChaoYuan, ChangFa Mid Road, BanTian Subdistrict, LongGang District, ShenZhen, China 518000
Phone: +86-15089309815
Email: deng0124@163.com
Compliance:
This product complies with the essential requirements of relevant EU directives and bears the CE mark.
Image: CE Mark and recycling symbols indicating compliance with EU directives and environmental responsibility.
Important Note:
This manual is intended to provide general guidance. Actual operation must be based on actual site conditions and professional electrical standards. The manufacturer reserves the right to update this manual as needed for product improvements; the latest version can be downloaded from our website.