1. About This Manual
This manual applies only to the Sunster TB10Pro (Model: XMZ-TB10) diesel parking heater. It is the original instruction manual, and all instructions should be read carefully before operating the device.
The product complies with relevant standards and regulations. Installation of this device must comply with all applicable regulations, and it should only be operated in well-ventilated areas. Please read this user manual before installing and using this equipment.
Properly store the product. Check for any abnormalities before use; if abnormal, discontinue use immediately.
Use the product according to its intended purpose to prevent potential injury from misuse.
2. Safety Warnings
WARNING:
Read all safety warnings, instructions, illustrations, and specifications provided with this diesel heater. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
General Safety Precautions
- Do not modify important components of the diesel heater.
- Do not use unauthorized spare parts from other manufacturers.
- Adhere strictly to instructions and guidelines during installation and operation.
- Only use original attachments and spare parts for installation and maintenance.
- Do not use the heater in areas where flammable vapor or dust may form (e.g., fuel depots, carbon/timber storehouses, granaries, diesel/petrol stations). Keep away from fuel tanks, compression tanks, fire extinguishers, clothes, or other flammable objects.
- Do not use a cigarette lighter for startup.
- Do not use the heater in closed and/or unventilated places.
- Turn off the heater when filling fuel.
- Do not cut off the electric power during operation.
- If there is a fuel leak or discharge from the fuel system, contact Sunster for repair.
- Place the exhaust outlet outdoors to prevent exhaust gas infiltration.
- Do not directly cut off the electric power to stop the heater from working during operation.
- Seal all gaps between the mounting plate and the car body.
- If the machine stops heating due to over-temperature protection, do not power it off immediately. Allow it to cool naturally before restarting.
- After turning off the machine, do not immediately disconnect the power supply. It takes 3-5 minutes for the machine to stop working completely.
- After starting the machine for 3-5 minutes, it will work normally and heat up. Please wait patiently.
- When the heater is just started, the current is relatively high, so an adapter with a voltage of 12-24V and a current of 12A or greater is required for the power supply.
Flammable Material Warning
WARNING: Flammable material
During installation/use, service, and disposal, ensure no flammable substances are near the exhaust pipe. The exhaust pipe's temperature is very high when operating. Avoid causing a fire by igniting flammable material.
Toxic Material Warning
WARNING: Toxic material
During installation/use, service, and disposal, install the appliance with space for ventilation to prevent carbon monoxide poisoning. Place the exhaust outlet outdoors to prevent exhaust gas from seeping in.
Fuel Tank Requirements
- If there is a leak, fuel should be discharged to the ground and must not contact hot parts of the vehicle or load.
- Fuel tanks containing gasoline should have an effective flame arrester at the fuel filling port, or a sealing device to completely seal the opening.
FCC Information
CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This product may cause harmful interference. (2) This product must accept any interference received, including interference that may cause undesired operation.
This product generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try to correct it by reorienting/relocating the receiving antenna, increasing separation between equipment, connecting to a different circuit, or consulting a dealer/experienced technician.
3. Product Introduction
3.1 Product Overview
The Sunster TB10Pro diesel heater operates independently of the vehicle's engine system and is powered by a 12-24V DC power supply. It offers two control modes: automatic and manual. Using light diesel fuel suitable for ambient temperatures, the heater can start and operate normally at temperatures above -40°C. Fresh air is drawn in, heated via a heat exchanger using energy from fuel combustion, and then delivered to the desired location. Key advantages include a compact structure, lightweight design, high thermal efficiency, energy conservation, environmental friendliness, and ease of installation.
3.2 Explanation of Principles
Heat Source:
Upon startup, the glow plug heats up (1-3 minutes). The fan then supplies air to the combustion chamber, and the diesel pump delivers fuel. Atomized diesel mixes with air and ignites upon contact with the hot glow plug, generating significant heat. High-temperature exhaust gases are discharged through the exhaust outlet at the bottom.
Heating:
Heat from the combustion chamber is rapidly transferred to an aluminum heat exchanger and dissipated via aluminum fins into the warm air ducting. An external fan blows air across the heat exchanger, and the heated air is discharged through the warm air outlet.
Control:
The controller is integrated into the unit for direct operation. The switch panel allows monitoring of operating status, adjusting settings, and scheduling operations. Remote control is also possible via a dedicated application.
3.3 Internal Structure
The heater features an all-in-one toolbox-style integrated machine, making it easy to carry for outdoor activities. It includes a built-in air filter at the bottom for easy cleaning and maintenance.

1. Hot Air Outlet, 2. Exhaust Pipe, 3. Metal Buckle, 4. Air Filter, 5. Power input interface, 6. Air Inlet, 7. Machine Upper Cover, 8. Switch Remote Control Placement Box.

3.4 Product Model Table
| No. | Part Name | No. | Part Name |
|---|---|---|---|
| 1 | Fuel Tank | 2 | Fuel Filter |
| 3 | Fuel Pump | 4 | Motor Assembly |
| 5 | Combustion Chamber | 6 | Heat Exchanger |
| 7 | Main Control Board | 8 | Glow Plug |
| 9 | Plastic Housing | 10 | Warm Air Duct |
| 11 | Air Outlet | 12 | Double-end Screw |
| 13 | Fuel Line | 14 | Clamp |
| 15 | Air Filter | 16 | Air Intake Pipe |
| 17 | Exhaust Pipe | 18 | Muffler |
| 19 | Power Cord Plug | 20 | Fuse |
| 21 | LCD Control Panel | 22 | Remote Controller |
| 23 | Fan Assembly Gasket | 24 | Combustion Chamber Gasket |
| 25 | Glow Plug Atomization Mesh | 26 | Temperature Sensor |
| 27 | Wiring Harness |
4. Specifications
| Attribute | Value |
|---|---|
| Brand Name | Sunster |
| Model | TB10 Pro (XMZ-TB10) |
| Heater Power | 8kw |
| Fuel | Diesel |
| Rated Voltage | DC 12V&24V ;AC 110-240V |
| Adapter Input | AC110-240V 50-60Hz |
| Tank Capacity | 5L |
| Fuel Consumption | 0.26-0.46 (L/H) |
| Adjustable Temp. Range | 46°F-95°F / 8°C-35°C |
| Heater Working Temperature | -40℃~+20℃ / -40°F~+68°F |
| Oil Pump Working Temperature | -40℃~+20℃ / -40°F~+68°F |
| Control Method | Bluetooth+LCD Screen+Smart Remote Control |
| Applicable Range | 215-269ft² / 20-25m² |
| Item Weight | 9.85kg |
| Item Height | 27cm |
| Item Width | 28cm |
| Item Length | 42cm |
| Material | Aluminum + Plastic |
| Switch Type | LCD Switch |
| Car Air Conditioning Type | Heating and ventilation |
| Certification | RoHS, CE, UKCA, ETL, ECE R122 & R10 |
| Feature 1 | Adaptive Plateau (Display Altitude, Automatic) |
| Feature 2 | Automatic Start & Stop (constant temperature) |
| Feature 3 | Temperature compensation |
| Feature 4 | Ventilation Mode |
| Feature 5 | Turbo Heat Mode |
| Feature 6 | CO Safety Monitoring |
| Feature 7 | 24h Time setting |
| Feature 8 | Temperature /Gear regulation |
| Feature 9 | Ultra Quiet Mode (< 35db) |
5. Setup (Installation Instructions)
This compact heater is relatively easy to install, with simplified piping. You simply need to install the exhaust pipe and connect the AC/DC power supply to get started. Please extend the exhaust pipe outdoors to vent combustion exhaust gases.
Note:
The exhaust gas temperature can reach up to 400°C; keep it away from pets and children, and ensure sufficient clearance from the ground to avoid damaging the flooring or lawn.
5.1 Installation Diagram

The image shows the main heater unit, exhaust pipe, heat protection sleeve, and air output pipe. The intake pipe and filter are pre-installed at the machine bottom.

Includes: Air Diesel Heater, LCD Switch, Smart wireless remote, Heat Protection Sleeve, Battery Power Cord, AC-DC Adapter Power, Air Outlet Pipe, Exhaust Pipe, Air Silencer.
5.2 Installation Steps (Refer to video for visual guide)
- Install the Exhaust Pipe: Rotate to secure the exhaust pipe to the heater unit.
- Install the Heat-Insulating Sleeve: Slide the heat-insulating sleeve over the exhaust pipe.
- Install the Muffler: Rotate to secure the muffler onto the end of the exhaust pipe, over the heat-insulating sleeve.
- Install the Outlet Air Duct: Rotate clockwise to secure the air outlet duct to the front of the heater unit.
- Install the Power Wiring: Connect the red wire to the positive (+) terminal and the black wire to the negative (-) terminal of a 12V/24V battery. Ensure a firm connection. Then, plug the power cord into the heater's power input interface.
- Diesel Fuel Filling: Open the top cover of the heater and add diesel fuel to the designated tank.
- Heater Startup: After installation, the heater should start normally. Press the power button on the LCD switch to turn it on.
- Pair the Remote Control: In the power-off state, press and hold both the 'minus' and 'plus' keys simultaneously on the LCD switch until "ADD" appears on the screen. Then, press and hold the plus (+) key on the remote controller until the Bluetooth icon flashes on the screen. It will automatically enter pairing mode. After "SuC" appears on the LCD switch, pairing is successful. To operate, press and hold the power key on the remote.
- Connect to the App via Mobile Bluetooth: Scan the QR code in the manual (or search 'Sunster' in app store) to download the Sunster App. Open the app, search for the device, and connect via Bluetooth.
This video provides a visual, step-by-step guide for installing the exhaust pipe, heat-insulating sleeve, muffler, outlet air duct, power wiring, filling diesel fuel, starting the heater, pairing the remote, and connecting to the mobile app. It also highlights important safety instructions.
5.3 Installation Precautions
No Side Installation:
Side installation of the diesel heater can lead to oil leaks inside the machine over time, producing smoke and carbon monoxide. Ensure a 10cm space around the heater for good ventilation.
- Indoor Installation: Make holes in the wall for the exhaust pipe to be placed outdoors. Insulate the exhaust pipe as it can become very hot and cause fire.
- Outdoor Installation: Extend the exhaust pipe to prevent exhaust gases from being sucked into the building from the back fan position, which can lead to carbon monoxide poisoning.
Warning:
- The air inlet must not be blocked; keep it open and clear.
- Keep the exhaust pipe clear. The exhaust pipe outlet must be kept away from anything flammable to avoid heating and igniting flammable goods.
- For optimal combustion, the smoke exhaust pipe must be placed horizontally or downward, not upward.
Power Supply Precautions:
- The power supply must be 12-24V DC with a current of ≥12A.
- When powered by a battery, do not charge the battery while using the heater, as insufficient current can cause malfunction.
- Ensure a firm and secure connection to the battery. Poor contact can result from using clamps for fixation.
- When extending the power cable, the wire diameter should be >2 mm². Thin wires can lead to insufficient current.
- After connecting, use insulating tape to protect connections and prevent electrical leakage.
- Do not disconnect power when the heater is operating at high temperatures to prevent backfire and permanent damage. If power is cut, wait until the internal heat dissipates completely before restarting.
- If the heater is turned on a long time after a power cut, incomplete combustion may produce smoke. Wait for the smoke to clear, then the heater will automatically start.
- Use high-grade diesel fuel. Kerosene, vegetable oil, gasoline, waste oil, etc., cannot be used, as they may cause unpleasant odors and malfunction.
6. Operating Instructions
6.1 Controller Panel Labeling

The heater can be controlled via a wireless temperature sensing switch, Bluetooth app, or the integrated LCD panel.

Features a built-in thermostat, CO monitor with auto shut-off, and one-button control for power, modes, and temperature.

The app offers timing function, blow mode, temperature setting, gear setting, and automatic start/stop for both iOS and Android devices.
| No. | Function |
|---|---|
| 1 | Decrease button |
| 2 | Ventilation button |
| 3 | Gear button/Heat button |
| 4 | Temperature control/constant temperature button |
| 5 | Power button |
| 6 | Add button |
| 7 | LCD display window |
| 8 | Ambient temperature sensor vent |
| 9 | Speaker |
6.2 Operating Modes
- Ventilation Mode: Only the fan operates (no heating). Fan speed can be set to levels 1–10.
- Gear Mode: Heating operates at a specific set level (1–10).
- High-Heat Mode: Heater operates at maximum output power for up to 2 hours continuously.
- Temperature Control Mode: Operating level adjusts automatically based on the difference between set and ambient temperatures. Minimum operating level is Level 1 (continuous operation). Temperature setting range: 8-35°C (46-95°F).
- Constant Temperature Mode: Similar to Temperature Control Mode. Heating stops and the unit enters standby when ambient temperature exceeds set temperature by 1°C. Heating resumes automatically when ambient temperature drops 2°C below set temperature. Customization of temperature differentials for starting and stopping is supported.
6.3 Functional Settings Operation Guide
General System Settings:
In running state, long press the power off button for 3s to display F0 on the LCD screen, entering setting mode. Use add/decrease buttons to switch setting codes. Press the ventilation button to enter the setting item. When the item flashes, use add/decrease buttons to adjust the value. Press the ventilation button again to confirm.
| Setting Code | Function Name | Parameter Adjustment Description |
|---|---|---|
| F0 | Current Time Setting | Adjust current time (HH:MM, 24-hour system). |
| F1 | Timer Start Time Setting | Set scheduled start time point. |
| F2 | Timer Running Duration Setting | Set running duration after start (00:00-10:00, 30-minute steps; 00:00 for unlimited). |
| F3 | Timer Function On/Off Setting | Set to ON to enable timer, OFF to disable. |
| F4 | Voice Broadcast Language Setting | Choose language (E=English, G=German, R=Russian, -=mute). |
| F5 | Ambient Temperature Compensation Setting | Adjust temperature compensation value (-15°C to 15°C) if displayed ambient temperature deviates from actual. Factory default is 0°C. |
| F6 | Constant Temperature Function Setting | Only applicable for on/off setting on the app, not set separately on heater. |
| F7 | Temperature Unit Switch Setting | In running state, long press add button for 3s to cycle between Fahrenheit (°F) or Celsius (°C). |
| F8 | Altitude Unit Switch Setting | Switch between Km (kilometers) and Kft (thousand feet). |
| F9 | Screen Brightness Adjustment | Adjust backlight brightness (0-10). 0 means backlight off, 10 means full brightness. Backlight automatically reduces after 120s of inactivity. |
| FA | Network Configuration with Sub-device | Enter network configuration mode by holding power off and add buttons for 3s. LCD shows "Add". If successful, "SuC" appears. If unsuccessful, hold decrease button for 3s until "Clr" appears to reset. |
| Fb | Ambient Temperature Value Acquisition with Sub-device | Adjust to acquire ambient temperature from sub-device (oN) or switch (oF). Default is oN. |
Remote Control Matching/Clearing:
In the power-on state, press and hold the add and decrease buttons simultaneously to enter engineering mode. Navigate to the EN07 interface and long press the ventilation button. The LCD screen will display P-1, indicating it's waiting for matching. Press any button on the remote control to start matching. After successful matching, it will return to the running interface. To clear remote control matching information, in the power-off state of the switch, press and hold the power off button, then connect the power. When the LCD screen changes from CLr to SuC, the matching information is cleared.
Engineering Mode:
In the running state, press and hold the add button and decrease button for 3 seconds to enter engineering mode and view the heater running status.
| Parameter Code | Parameter Meaning |
|---|---|
| En00 | Heater mainboard firmware version |
| En01 | Fault code |
| En02 | Furnace body temperature |
| En03 | Power supply voltage |
| En05 | Switch local ambient temperature |
| En06 | Current altitude |
| En07 | Remote control pairing status |
| En08 | Local Bluetooth ID |
6.4 Smart Remote Control Function
The 3-in-1 Smart Remote (Model: 2422A1) integrates a temperature sensor, CO monitor, and heater control. After matching with the heater switch, you can control the heater and monitor its working status.
- CO Detection: Displays and monitors current environmental CO concentration. An alarm sounds if the standard is exceeded. If seriously exceeded, the heater will automatically shut off.
- Ambient Temperature Detection: Displays current ambient temperature. When connected to the heater switch, you can choose to use the temperature detected by the heater switch or the remote.
- Display Current Time: Displays current time. When connected to the heater switch, it automatically synchronizes with the heater switch's time.
6.5 App Control
The Sunster TB10Pro supports Bluetooth connectivity for remote operation within 30 meters via a dedicated app. The app is available for both iOS and Android devices.

The app allows for timing functions, blow mode, temperature setting, gear setting, and automatic start/stop.
App Download:
Scan the QR code in the manual to download the Sunster App for Android or iOS, or search for "Sunster" on Google Play (Android) or the App Store (iOS).


Scan the left QR code for Android, and the right QR code for iOS. Alternatively, search 'Sunster' in your device's app store.
7. Maintenance
- If black smoke is observed during operation or in the second year of use, it indicates carbon accumulation in the combustion chamber. This requires timely cleaning.
- If any of the above situations occur (e.g., black smoke), please replace the Air Filter and Fuel Filter in a timely manner.
- The built-in air filter at the bottom of the unit is designed for easy cleaning and maintenance.
8. Troubleshooting (Fault Code Table)
| Fault Code | Fault Cause | Solution |
|---|---|---|
| E01 | Voltage Abnormality |
|
| E03 | Glow Plug Abnormality |
|
| E04 | Fuel Pump Abnormality |
|
| E05 | Overheat Protection |
|
| E06 | Fan Abnormality |
|
| E07 | Air Intake Sensor Abnormality |
|
| E08 | Fuel shortage and flameout |
|
| E09 | Overheat sensor abnormality |
|
| E10 | Startup failure |
|
| E11 | Carbon monoxide exceeding standard |
|
9. User Tips
- Quiet Operation: The TB10Pro features a new silent oil pump and upgraded muffler, reducing noise to as low as 35 dB. This makes it suitable for overnight use in vans, campers, or tents without disturbing rest.
- CO Monitoring for Safety: Utilize the 3-in-1 smart remote's built-in CO monitor with auto shut-off for enhanced safety, especially when sleeping.
- Flexible Control: Take advantage of the three control methods: the LCD panel for direct adjustments, the wireless remote for convenience, and the Bluetooth app for remote operation up to 30 meters away.
- Energy Efficiency: Use the 'Constant Temperature Mode' to stabilize indoor temperature and reduce fuel consumption, as it automatically adjusts power output and can auto start/stop.
- Easy Setup: The pre-installed air intake pipe and filter simplify initial setup. For quick deployment, ensure the exhaust pipe and air outlet hose are properly connected using the quick-connect design.
10. Warranty and Support
Responsibility Requirements:
Sunster is not responsible for any issues arising from non-compliance with these instructions and precautions. The company is also not responsible for issues resulting from repairs conducted without professional maintenance or the use of non-original spare parts/accessories. Such maintenance will invalidate the heater's type approval and ECE type approval certificate.
Contact Information:
If you encounter any issues, please contact the store's customer service team directly via the sales platform or reach out via email.
- After-sales Support: cs@sunster.tech
- Business Inquiries: sunster@sunster.tech
For additional information, please visit the official Sunster website.
