General Guidelines
- Please read these instructions carefully and use the product accordingly.
- Please keep this manual and hand it over when you transfer the product.
- This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed.
Notes
- The product is intended for indoor use only. The product must be assembled and used in accordance with the provisions of the manual. Personal injury and/or damage to product may occur if products are used outside of their intended purposes and/or if products have been changed/modified from their original design. The seller does not assume any responsibility or liability with respect to any injury/damage caused by incorrect assembly or improper use.
- Keep the product away from fire sources and high temperatures.
- Please assemble the item on a spacious surface and do not place the unwrapped product directly on the ground to avoid product damage.
- Please wear gloves during the assembly and/or disassembly process to avoid scratches from any sharp edges.
- Please match the corresponding part and fitting based on the part number in the manual.
- Periodically inspect screw tightness while the product is in use. If necessary, retighten to ensure structural integrity.
- If you accidentally spill water or another liquid on the surface, immediately wipe clean with a dry towel.
- Please place this item on level, solid ground during use.
Warnings
- It is not intended for use by children under 3 years of age. Children must be under adult supervision to use the product.
- Children should not climb or play on the product in order to avoid tipping over the furniture and causing serious injury.
- During assembly, keep all small parts out of the reach of children. It may be fatal if swallowed or inhaled.
- To avoid the potential dangers of suffocation, please keep all parts and packaging (film, plastic bags, foam, etc.) away from babies and children.
EN WARNING: Furniture Tip-Over Hazard
Serious or fatal crushing injuries can occur from furniture tip-over. To reduce the risk of furniture tipover:
- ALWAYS install tipover restraint provided.
- NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
Warning symbol indicating potential furniture tip-over hazard.
Assembly Instructions
A detailed assembly guide is available in PDF format: User Manual (PDF).
Parts List
Please refer to the following diagrams for all included parts and hardware. Ensure all components are present before beginning assembly.
Exploded view of all vanity and stool components, showing their relative positions.
Panels (Box 1/2 & 2/2)
Panels 1-16 with their respective dimensions.
Panels 17, 26-28, and P with their respective dimensions.
Panels 18-25 with their respective dimensions.
Hardware (Box 1/2)
Hardware components A through N with quantities.
Hardware components O through V with quantities.
Special Fastener Instructions (If Applicable)
Detailed instructions for assembling Quickfit and Cam Lock fasteners.
Quickfit Installation:
- Tighten quickfit until the shoulder is flush with the panel. Do not overtighten or undertighten.
Cam Lock Installation:
- When fitting cam lock, ensure the starting position is correct before inserting the connecting quickfit.
- The Quickfit head should be in the center of the cam lock when the two panels are joined.
- Cam lock should be inserted before quickfit.
- Turn cam lock clockwise to tighten.
Step-by-Step Assembly
-
Step 1: Prepare Drawer Slides
Attach component M (drawer slide) to the CR and DR parts. Ensure correct orientation.
Diagram showing the attachment of drawer slide M to CR and DR components.
-
Step 2: Attach Drawer Runners to Panels
Attach the U components to panels 10 and 9 using screws D and A1 fasteners. Ensure the runners are aligned correctly.
Diagram illustrating the attachment of U components to panels 10 and 9 using D screws and A1 fasteners.
-
Step 3: Assemble Side Panels to Base
Attach panels 16 and 15 to panel 10 using A2 fasteners and C dowels.
Diagram showing how to connect panels 16 and 15 to panel 10 using A2 and C.
-
Step 4: Complete Base Structure
Attach panel 9 to panels 16 and 15, connecting to panel 10 using A2 fasteners and C dowels.
Diagram showing the completion of the base structure by attaching panel 9.
-
Step 5: Prepare Shelf Panels
Insert A1 fasteners into both sides of panel 4.
Diagram showing the insertion of A1 fasteners into panel 4.
-
Step 6: Attach Top Shelf
Connect panel 5 to panel 4 using C dowels and A2 fasteners.
Diagram showing the connection of panel 5 to panel 4.
-
Step 7: Prepare Shelf Panel 3
Insert A1 fasteners into panel 3.
Diagram showing the insertion of A1 fasteners into panel 3.
-
Step 8: Connect Shelf Panels
Attach panel 4 to panel 3 using A2 fasteners.
Diagram showing the connection of panel 4 to panel 3.
-
Step 9: Add Side Shelves
Attach panels 6 to panels 4 and 3 using A2 fasteners.
Diagram showing the attachment of panels 6 to the shelf structure.
-
Step 10: Prepare Vertical Panels
Insert A1 fasteners into panels 1 and 2.
Diagram showing the insertion of A1 fasteners into panels 1 and 2.
-
Step 11: Assemble Top Shelf Unit
Attach panels 5, 4, 6, and 3 to panel 1 using A2 fasteners, forming the upper shelf unit.
Diagram showing the assembly of the top shelf unit with panel 1.
-
Step 12: Complete Top Unit Frame
Attach panel 2 to the assembly from Step 11 using A2 fasteners.
Diagram showing the completion of the top unit frame by attaching panel 2.
-
Step 13: Insert Back Panel for Mirror Section
Slide panel 27 into the grooves of the main frame (panels 1, 2, 3, 4, 6, 26).
Diagram showing the insertion of panel 27 into the main frame.
-
Step 14: Attach Back Panel to Vanity Base
Attach panel 8 to the back of the main frame (panels 1, 3, 27, 2) using screws H.
Diagram showing the attachment of panel 8 to the back of the vanity base.
-
Step 15: Secure Back Panel
Attach panel 8 to panel 1 using A1 fasteners.
Diagram showing the securing of panel 8 to panel 1.
-
Step 16: Connect Top and Base Units
Connect the assembled top mirror/shelf unit (from Step 12) to the vanity base (from Step 15) using C dowels and A2 fasteners.
Diagram showing the connection of the top and base units of the vanity.
-
Step 17: Install Mirror Supports
Attach S components to the mirror unit (panels 1, 2, 7, 8, 9, 10, 16).
Diagram showing the installation of mirror supports S.
-
Step 18: Attach Hinges to Mirror Door
Attach Q hinges to panel 17 (the mirror door) using screws D.
Diagram showing the attachment of hinges Q to mirror door panel 17.
-
Step 19: Mount Mirror Door
Mount panel 17 (mirror door) to the vanity unit by attaching the hinges to the main frame using screws D.
Diagram showing the mounting of mirror door panel 17 to the vanity.
-
Step 20: Adjust Mirror Door (Optional)
Adjust the mirror door for proper alignment and smooth operation. Refer to the hinge adjustment diagram if needed.
Diagram showing how to adjust the mirror door hinges for optimal fit.
-
Step 21: Assemble Drawer Sides (x2)
Connect panels 12, 14, and 13 to form the drawer sides using screws G. Repeat for the second drawer.
Diagram showing the assembly of drawer sides using panels 12, 14, 13 and screws G.
-
Step 22: Insert Drawer Bottom (x2)
Slide panel 28 (drawer bottom) into the grooves of the assembled drawer sides. Repeat for the second drawer.
Diagram showing the insertion of drawer bottom panel 28 into the drawer sides.
-
Step 23: Prepare Drawer Front (x2)
Attach J and I components to panel 11 using B1 fasteners. Repeat for the second drawer front.
Diagram showing the attachment of J and I components to panel 11 for the drawer front.
-
Step 24: Attach Drawer Front to Drawer Box (x2)
Connect the assembled drawer front (panel 11 with J, I, B1) to the drawer box (panels 14, 13, 28) using B2 fasteners. Repeat for the second drawer.
Diagram showing the connection of the drawer front to the drawer box.
-
Step 25: Install Drawer Slides to Drawers (x2)
Attach the DL and DR drawer slides to the sides of the assembled drawers (panels 13, 28, 11) using screws D. Repeat for the second drawer.
Diagram showing the installation of DL and DR drawer slides to the drawers.
-
Step 26: Insert Drawers into Vanity
Carefully slide the assembled drawers into the vanity unit's runners.
Diagram showing the insertion of the assembled drawers into the vanity unit.
-
Step 27: Install Anti-Tip Brackets to Vanity
Attach R anti-tip brackets to the back of the vanity (panels 2, 27, 26, 15, 10, 16) using screws D.
Diagram showing the installation of anti-tip brackets R to the back of the vanity.
-
Step 28: Secure Vanity to Wall
Secure the vanity to the wall using the provided anti-tip kit T (T1, T2, T3, T4, T5). Follow the instructions for wall mounting carefully to prevent tip-over.
Diagram showing how to secure the vanity to the wall using the anti-tip kit T.
-
Step 29: Prepare Stool Base Panels
Insert A1 fasteners into panels 19 and 18.
Diagram showing the insertion of A1 fasteners into stool base panels 19 and 18.
-
Step 30: Assemble Stool Side Panels
Attach panel 24 to panels 18 and 19 using C dowels and A2 fasteners.
Diagram showing the attachment of panel 24 to stool side panels 18 and 19.
-
Step 31: Prepare Stool Bottom Panel
Insert B1 fasteners into panel 20.
Diagram showing the insertion of B1 fasteners into stool bottom panel 20.
-
Step 32: Attach Stool Bottom Panel
Attach panel 20 to panels 18, 24, and 19 using C dowels and B2 fasteners.
Diagram showing the attachment of stool bottom panel 20 to the stool frame.
-
Step 33: Attach Stool Top Panel
Attach panel 21 to the top of the stool frame (panels 19, 20, 18, 24) using C dowels, V covers, and H screws.
Diagram showing the attachment of stool top panel 21 to the stool frame.
-
Step 34: Install Casters and Cushion Mounts
Attach E screws and N casters to panel 21 and the stool frame (panels 19, 20, 18, 24).
Diagram showing the installation of casters N and cushion mounts E to the stool.
-
Step 35: Prepare Stool Drawer Fronts
Attach J and I components to panels 22 and 23 using A1 fasteners.
Diagram showing the preparation of stool drawer fronts with J, I, and A1.
-
Step 36: Attach Stool Drawers
Attach panels 22 and 23 (stool drawer fronts) to the stool frame (panels 18, 20, 24, 21) using C dowels and A2 fasteners.
Diagram showing the attachment of stool drawers 22 and 23 to the stool frame.
-
Step 37: Install Stool Lid Hinge
Attach F hinges to panel 22 and the stool frame (panels 18, 19, 20, 24).
Diagram showing the installation of stool lid hinge F.
-
Step 38: Attach Stool Lid
Attach panel L to panel 25 (stool lid) and connect K hinges to panel 22 and the stool frame (panels 18, 19, 20, 24) using screws D.
Diagram showing the attachment of stool lid 25 with hinges K and panel L.
-
Step 39: Place Stool Cushion
Place panel P (cushion) on top of the stool (panels 22, 25, 19, 20).
Diagram showing the placement of stool cushion P on the stool.
-
Step 40: Secure Stool Cushion
Secure panel P (cushion) to the stool. (Specific fastening method not detailed in diagram, typically involves screws from underneath or adhesive pads).
Diagram showing the securing of stool cushion P to the stool.
-
Step 41: Final Check
Ensure all parts are securely fastened and the vanity and stool are stable. The assembly is now complete.
Diagram showing the fully assembled vanity and stool.
Operating Instructions
- Using the Mirror: The high-definition rectangular mirror provides a clear, distortion-free reflection for makeup application and skincare routines.
- Storage Compartments: Utilize the two main drawers for cosmetics, jewelry, and styling tools. The hidden compartment behind the mirror, with its adjustable shelf, is ideal for skincare products and razors. The top shelf and three open cubbies offer easy access for brushes, perfumes, and other frequently used items.
- Mobile Stool with Storage: The stool is designed to tuck completely under the table when not in use, saving space. The lift-up seat reveals a hidden storage space, perfect for scarves or other accessories. The universal casters allow for silent and effortless movement of the stool.
The high-definition mirror provides a clear reflection for daily routines.
Illustration of the vanity's multi-zone storage, including drawers and shelves.
The mobile stool features hidden storage under its lift-up seat and smooth-rolling casters.
The stool neatly slides under the vanity, optimizing space in smaller rooms.
Maintenance
- Cleaning: Wipe surfaces with a soft, dry cloth. Avoid abrasive cleaners or harsh chemicals that may damage the melamine finish. If liquids are spilled, wipe immediately with a dry towel.
- Hardware Check: Periodically inspect all screws and fasteners to ensure they are tight. Retighten if necessary to maintain structural integrity and stability.
- Mirror Care: Clean the mirror with a glass cleaner and a soft, lint-free cloth.
Troubleshooting
- Instability/Wobbling: Ensure the vanity and stool are placed on a level, solid surface. Check all assembly screws and fasteners, tightening any that are loose. Verify that all panels are correctly seated.
- Drawers Not Sliding Smoothly: Check that the drawer slides (M, DL, DR) are correctly installed and free from obstructions. Ensure the drawers are not overloaded.
- Mirror Door Misalignment: If the mirror door does not close properly or is uneven, adjust the hinges (Q) as shown in Step 20 of the assembly instructions.
Specifications
| Feature | Detail |
|---|---|
| Overall Dimensions (Vanity) | 60 cm (Width) x 40 cm (Depth) x 132.5 cm (Height) |
| Overall Dimensions (Stool) | 57 cm (Width) x 38 cm (Depth) x 55 cm (Height) |
| Material | Particle Board with Melamine Finish |
| Frame Material | Wood |
| Vanity Weight Capacity | Up to 30 kg |
| Stool Weight Capacity | Up to 120 kg |
| Storage | 4 Drawers, Open Storage Shelves, Hidden Mirror Compartment, Stool Storage |
Detailed dimensions of the vanity table and the mobile stool.
User Tips
- For smaller rooms, utilize the stool's ability to tuck completely under the vanity to maximize floor space.
- Organize frequently used items on the open shelves for quick access, and store less common items in the drawers or the hidden mirror compartment.
- Use the stool's internal storage for items like scarves, hair accessories, or small bags to keep your space tidy.
- Always place heavier items in the lower drawers of the vanity to enhance stability and reduce the risk of tipping.
Warranty & Support
For any questions or assistance, please contact our customer care center. Our contact details are below:
United States Support:
- Phone: 001-877-644-9366
- Email: customerservice@aosom.com
- Importer: Aosom LLC, 7777 Center Ave. Suite 430, Huntington Beach, CA 92647-9998 USA
Please have your model number (83D-233V70_83D-233V90) ready when contacting support for faster service.