Flytec V802 Pro

Contents

Flytec V802 Pro GPS Fishing Bait Boat

User Manual

1. Introduction

Thank you for choosing the Flytec V802 Pro GPS Fishing Bait Boat. This advanced remote-controlled bait boat is designed to enhance your fishing experience with features like GPS positioning, multiple bait hoppers, and long-range control. Please read this manual thoroughly before operating the boat to ensure safe and efficient use.

Flytec V802 Pro GPS Fishing Bait Boat on water

The Flytec V802 Pro GPS Fishing Bait Boat in action on the water.

2. Package Contents

Please check the package to ensure all items are present:

Flytec V802 Pro GPS Fishing Bait Boat and accessories

All components included in the Flytec V802 Pro package.

  • 1x Flytec V802 Pro Bait Boat
  • 1x Remote Controller
  • 1x 7.4V Battery (Capacity may vary: 5200mAh, 12000mAh, or 18000mAh)
  • 2x Antennas
  • 2x Control Sticks
  • 2x Propellers
  • 1x Remote Control Back Cover Screw
  • 1x Hanging Rope
  • 1x USB Cable
  • 1x Instruction Manual (this document)

3. Product Features

  • GPS Positioning: Adopts imported GPS positioning module with built-in high-sensitivity electronic compass sensor, offering accurate positioning with an error of 1 meter. Supports GPS L1, GALILEO E1, G1SBAS L1, GLONASS, QZSS L1, BEIDOU B1.
  • Long Control Distance: Up to 500 meters with dual antenna transceiver design for stable signal transmission and strong anti-interference capability.
  • High Load Capacity: Features 4 independent bait bins with a maximum bait load of 3KG.
  • Dual Motor System: Equipped with 390 powerful motors and 10A high current propellers for powerful propulsion and long-lasting stability. Anti-winding protective covers effectively prevent weeds and debris from entanglement.
  • Dual Battery Compartment: Can accommodate two large 7.4V 5200mAh, 12000mAh, or 18000mAh batteries for extended runtime (2-6 hours depending on battery capacity). Supports dual batteries for uninterrupted power supply, doubling battery life.
  • Waterproof Design: Fully sealed cabin and battery compartment ensure super waterproof performance, with 5-level wind resistance and a seamless, fully enclosed hull.
  • Gyroscope System: Built-in gyroscope system automatically corrects yaw, ensuring straight sailing under wind, waves, and loads.
  • Night Navigation: Bright night lights at the bow and turn signal lights at the tail for safer night navigation. Two light modes (constant on, flashing) adapt to different environmental requirements.
  • Fish Finder Compatibility: Stern hook design supports attachment of a fish finder (sold separately) to detect fish location in real-time.
Multi-satellite hybrid engine positioning system

The boat utilizes multiple satellite systems for precise positioning.

Waterproof design of the bait boat

The fully sealed and waterproof hull ensures durability in various conditions.

4. Setup

4.1. Battery Installation and Charging

  • The boat has a built-in battery. Simply connect the battery connector when using.
  • The battery compartment can accommodate two 7.4V batteries (5200mAh, 12000mAh, or 18000mAh). Using two batteries simultaneously will double the runtime.
  • To charge, connect the battery to the power supply using the provided USB cable.
Dual battery compartment

The dual battery compartment allows for extended operation.

4.2. Antenna Installation

Before using, both antennas need to be installed simultaneously on the boat for optimal signal reception and transmission.

4.3. Power On and Pairing

  1. Place the boat on flat ground, keeping the remote control at least 0.5 meters away from the boat.
  2. Turn on the boat switch first. Observe the tail light flashing.
  3. Then, turn on the remote control.
  4. When the remote control makes a "beep" sound, the indicator light on the remote control will be solid green, and the boat light will be solid on. This indicates that the remote control and the boat are connected.
  5. At this point, the boat light icon will be displayed on the remote control interface, but the GPS icon will not be displayed yet.
  6. Note: If pairing is unsuccessful or the remote control disconnects from the boat, turn off the power of both the boat and the remote control, then repeat the pairing process.

4.4. Calibration

The boat needs to be calibrated before use. After the remote control and boat are matched, the GPS satellite icon will be displayed on the remote control screen. When the number next to the icon is greater than 8, calibration can be performed.

  1. Drive the boat a few meters away from the shore.
  2. Press the calibration button on the remote control.
  3. The boat will turn left and right in the water.
  4. When the boat stops turning after calibration, the remote control will emit two "beep" sounds, indicating successful calibration.

5. Operating Instructions

5.1. Remote Control Overview

Remote control diagram with labeled buttons

Detailed layout of the remote control buttons and functions.

ComponentFunction
AntennaSignal transmission/reception
Lighting ButtonControls boat lights (steady on, flashing, off)
Power IndicatorIndicates remote control power status
Left JoystickControls boat direction (forward/backward, left/right)
Front Left SiloControls front left bait hopper
SwitchPower switch for remote control
Back Left SiloControls back left bait hopper
Calibration ButtonInitiates boat calibration
Cruise ButtonActivates/deactivates cruise control and fixed-speed cruise
Original Point ButtonSets/returns to the original starting point
Delete ButtonClears stored positioning points
Fishing Ground ButtonSelects fishing grounds (A, B, C, D)
Right JoystickControls boat direction (forward/backward, left/right)
Front Right SiloControls front right bait hopper
Back Right SiloControls back right bait hopper
OK ButtonConfirms selections
Up/Left/Right/Down ButtonsNavigation for menu and point selection

5.2. Panel Function Details

The remote control screen displays various icons and information:

Remote control screen icons explanation

Visual guide to the remote control display icons.

  • Boat Light Icon: Appears when boat lights are on. Flashes when boat lights flash.
  • Compass Icon: Shows the boat's direction after calibration. Defaults to 'N' if not calibrated.
  • Boat and Remote Power Icons: Left indicates boat battery power, right indicates remote control battery power.
  • GPS Signal Icon: Appears when GPS signal is acquired (number indicates satellites found).
  • Boat Driving Direction Icon: Lights up in the middle for forward/backward, left for left turn, right for right turn. Flashes on both sides during fixed-speed cruise.
  • Positioning Point Icon: Numbers around represent positioning point coordinates. Up to 40 points can be set across 5 pages.
  • Distance Icon: Displays distance to the original point or between two positioning points during cruise.
  • Fishing Ground Icon: ABCD represents 4 fishing grounds. Must be set before positioning points.
  • Original Point Icon: House icon represents the original point. Must be set for return function.

5.3. Baiting Operation

The boat features 4 independent silos for bait. Press the corresponding silo button on the remote control to release bait. The silos will pop up, and you need to manually restore them after baiting.

Four independent bait silos with different bait types

The boat's four independent silos can hold various types of bait.

Bait being released from the hoppers

The inverted bait display shows bait being released into the water.

5.4. GPS Functions

5.4.1. Fishing Ground Setting

After calibration, you must select a fishing ground before setting positioning points. ABCD represents 4 different fishing grounds. Initially, ABCD will flash slowly.

  1. Press the Fishing Ground button to select a fishing ground. The letter of the selected fishing ground will flash quickly.
  2. Press the OK button to confirm the selection. The selected letter will flash quickly and then remain solid, while the other three letters disappear, indicating successful selection.
  3. To switch fishing grounds, press the Fishing Ground button again.

5.4.2. Original Point Setting

This function requires more than 8 GPS satellites to be locked.

  1. After calibration, the boat stops at the shore as the starting point.
  2. Select the Original Point icon using the navigation buttons.
  3. Press the OK button to confirm. The Original Point icon on the remote control screen will flash first and then remain solid, and the coordinate background will darken, indicating successful setting.

5.4.3. Positioning Point Setting

After setting the original point, drive the boat to the desired location.

  1. Select a numerical positioning point (e.g., point 1) using the navigation buttons.
  2. Press the OK button to set the point. The selected point will flash first and then remain solid, and other unset coordinate numbers will disappear, indicating successful setting.
  3. You can drive the boat to other locations to set more positioning points.
  4. Each fishing ground has 5 pages, with each page displaying 8 positioning points and the origin. A single fishing ground can store up to 40 positioning points.
  5. Stored positioning points are retained even when the boat is turned off.
Fixed-point baiting and automatic return diagram

The boat supports up to 160 positioning points for precise baiting and automatic return.

5.4.4. Positioning Point Cruise

  1. Once positioning points are set, select the desired destination point.
  2. Press the Cruise button. The boat will automatically start cruising.
  3. The positioning point icon on the remote control screen will flash and then remain solid upon reaching the point.
  4. The screen displays the distance between the two positioning points. When the distance reaches 0m, the remote control will emit two "beep, beep" sounds, indicating the boat has reached the selected point and stopped.
  5. To cancel the cruise during operation, press and hold the Cruise button.

5.4.5. One-Key Return

This function requires the original point to be set first.

  1. Press the Original Point button. The boat will return to the original starting point.
  2. During return, the original point icon on the remote control will flash. It will become solid when the boat reaches the original position.
  3. To cancel the one-key return function midway, long press the Cruise button.

5.5. Fixed-Speed Cruise Control

  1. Push both joysticks forward for about 5 seconds to activate fixed-speed cruise control.
  2. Push both joysticks backward to exit fixed-speed cruise control.
  3. When fixed-speed cruise control is active, the boat icon on the remote control screen will light up in the middle and flash on both sides. Left and right turns can still be performed in this mode.

5.6. Light Switching

Short press the Lighting button on the remote control to cycle through the headlight and taillight status: "steady on" → "flashing" → "off". The light icon on the remote control display will switch accordingly.

5.7. Electronic Fence Function

After setting the origin, the boat will activate the electronic fence function. The boat cannot sail out of a safe distance of 500m from the origin.

5.8. Fish Finder Integration

The stern of the boat has a hook attachment design, allowing it to be upgraded with a fish finder (sold separately). This enables real-time detection of fish location for more efficient fishing.

Stern hook design for fish finder

The stern hook allows for easy attachment of a fish finder.

6. Maintenance

6.1. Remote Control

  • Remove batteries when not in use for a long time to prevent leakage.

6.2. Motor

  • Check the motors and propellers for any entanglements (e.g., weeds, fishing line) after each use.

6.3. Boat Hull

  • After each use, wipe off any moisture to keep the hull dry and clean.
  • If the battery is not used for a long time, remove it from the boat and charge it for storage.
  • Do not store corrosive liquids or items near the boat.
  • Keep the boat away from high-temperature objects.
  • When not in use, store the bait boat in a clean, dry place to prevent dust accumulation.

6.4. Accessory Replacement Tips

If you need to replace the boat circuit board, GPS module, or remote control, you must re-pair the frequency after replacement. Then, press and hold the calibration button until the boat light flashes and then turns off. After this, the boat can be used normally.

7. Troubleshooting

7.1. Lost Signal Return

If the remote controller's power is low, it automatically shuts down, or is manually turned off, the boat will automatically return to its original position point. This function requires the original point to be set first.

7.2. Low Battery Warning

When the boat's voltage is low, the remote controller will emit a beeping sound. If the remote controller's own voltage is low, it will continuously beep, and its indicator light will turn red.

7.3. Clearing Positioning Points

To clear all stored fishing spots on the remote controller, press and hold the Clear button. To cancel the coordinates of a single positioning point, select the corresponding number on the screen and short press the Clear button. The number box will disappear after clearing.

8. Specifications

Boat dimensions and specifications

Key dimensions and technical specifications of the bait boat.

FeatureSpecification
Item No.V802 PRO
Bait Load3kg
Boat Size52.7cm x 26.4cm x 50cm (20.6in x 10.4in x 19.7in)
Motor390 Powerful Motor
Control Distance500m
MaterialABS Material
ColorBlack/Orange
Net Weight2219g
Boat Battery Options7.4V 5200mAh / 12000mAh / 18000mAh
Control Battery4xAA Battery (Not Included)
Charging Time6h (5200mAh) / 8h (12000mAh) / 10h (18000mAh)
Playing Time2h (5200mAh) / 4h (12000mAh) / 6h (18000mAh)

9. User Tips

  • Pre-check: Always ensure batteries are fully charged and antennas are securely installed before heading out for fishing.
  • GPS Signal: For optimal GPS performance, wait until the remote control displays more than 8 satellites before setting original points or positioning points.
  • Bait Distribution: Utilize the independent hoppers to distribute different types of bait or release bait at various intervals to attract fish more effectively.
  • Night Fishing: The bright bow lights and tail turn signals are excellent for night fishing. Use the flashing mode for better visibility in low light conditions.
  • Range Awareness: While the boat has a 500m range, always be mindful of the boat's distance and battery level to ensure it can return safely, especially when using the electronic fence function.
  • Propeller Care: Regularly check propellers for any debris or fishing line entanglement to maintain optimal performance and prevent motor damage.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the seller's official website or contact their customer service directly. Keep your purchase receipt as proof of purchase.

You can also refer to the official PDF user manual for additional details: View User Manual (PDF)

11. Product Video

Watch a demonstration of the Flytec V802 Pro GPS Fishing Bait Boat's features and operation.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.