1. Introduction
Thank you for purchasing the Flytec V600 Pro RC Bait Boat with Built-in Fish Finder. This advanced fishing tool is designed to enhance your fishing experience with precise bait delivery, fish detection, and intelligent navigation. Please read this manual carefully before operating the device to ensure safe and optimal performance. Keep this manual for future reference.
1.1. Product Overview
The Flytec V600 Pro is a remote-controlled bait boat equipped with a comprehensive set of features for modern anglers. It includes a built-in fish finder, GPS/Beidou dual-mode positioning, dual independent bait hoppers, a long-range remote control, and smart auto-return functions. The fish finder operates on the principle of radio transmission, allowing you to assess water depth, fish presence, and fish school locations. The wireless sensor's battery is replaceable, ensuring long-term usability and cost efficiency.
Figure 1.1: Flytec V600 Pro Bait Boat Key Features
(1) GPS+Beidou Dual-Mode Positioning: Supports 4 fishing areas, 50 waypoints per area, total 200 waypoints. (2) Dual Independent Bait Hoppers: Continuous operation without power interruption. (3) Up to 6 Hours Runtime, 500m Ultra-Long Remote Range: High-capacity battery options (5200mAh, 12000mAh, 18000mAh). (4) Smart Auto Return & Electronic Fence Protection: One-key return, low battery return, signal loss return, electronic anchor, and geo-fence within 500m radius.
2. Safety Information
- Always operate the bait boat in open waters, away from swimmers, other boats, and obstacles.
- Do not operate the boat in strong winds or currents that exceed its capabilities.
- Ensure all battery compartments are securely sealed before placing the boat in water.
- Keep the remote control dry and away from water.
- Do not attempt to modify the boat or its components, as this may void the warranty and cause malfunction.
- Supervise children when they are near or operating the bait boat.
- Always turn off the boat and remote control when not in use.
- Charge batteries in a safe, supervised environment.
3. Package Contents
Please check the package contents against the list below. If any items are missing or damaged, contact your retailer.
Figure 3.1: Flytec V600 Pro Package Contents
(From left to right, top to bottom) Remote Control, Lanyard, Antenna*2, Sticker, Instruction Manual, Fish Finder Manual, Spare Propeller*2, 12000mAh Battery (or selected capacity), USB Charging Cable, Type-C Remote Control Charging Cable, Fish Finder Remote Control, Type-C Charging Cable for Fish Finder Remote Control, 5V 1A Charging Plug for Fish Finder Remote, Lanyard for Fish Finder Remote, Sonar Protective Cover, 5V 1A Car Charger for Fish Finder Remote.
| Item | Quantity |
|---|---|
| Bait Boat | 1 |
| Hull Battery | 1 (Optional capacity: 5200/12000/18000mAh) |
| Remote Control | 1 |
| Lanyard | 1 |
| USB Charging Cable | 1 |
| Type-C Remote Control Charging Cable | 1 |
| User Manual | 1 |
| Antenna | 2 |
| Spare Propeller | 2 |
| Fish Finder Remote Control | 1 |
| Fish Finder User Manual | 1 |
| Type-C Fish Finder Remote Charging Cable | 1 |
| 5V 1A Charging Adapter for Fish Finder Remote | 1 |
| Lanyard for Fish Finder Remote | 1 |
| Sonar Protective Cover | 1 |
| 5V 1A Car Charger for Fish Finder | 1 |
| Sticker | 1 |
4. Product Components
4.1. Hull Parts Diagram
Figure 4.1: Flytec V600 Pro Hull Parts Diagram
Key components include Antennas, Switch, Battery Indicator, Headlights, Tow Hook, Dual Motors, Right Silo, Left Silo, Battery Compartment Cover, Handle, and Rear Tail Lights.
4.2. Remote Control Button Layout
Figure 4.2: Flytec V600 Pro Remote Control Button Layout
The remote features a Joystick, Cruise Button/Positioning Point Button, Hook/Calibration, Fishing Ground Button, Cursor Left/Right, Speed/Electronic Anchor, Silo Selection, Original Point Button, Clear Button, Light Button, OK Button (long press to clear origin), and Power Switch. The Fish Finder Remote has Zoom, Power/Menu, Mode, Left, and Right keys.
5. Setup
5.1. Battery Installation
5.1.1. Bait Boat Battery
- Open the battery compartment cover located on the top-rear of the boat hull.
- Insert the fully charged hull battery (or two batteries for extended runtime) into the compartment, ensuring correct polarity.
- Securely close the battery compartment cover to ensure it is waterproof.
5.1.2. Remote Control Battery
- Open the battery cover on the back of the remote control.
- Insert the required batteries (refer to the remote control manual for type and quantity) with correct polarity.
- Close the battery cover.
5.1.3. Fish Finder Remote Control Battery
- Open the battery cover on the back of the fish finder remote.
- Insert the required battery (3.7V lithium battery) with correct polarity.
- Close the battery cover.
5.2. Antenna Installation
- Screw the two antennas onto the designated ports on the top of the bait boat.
- For the remote control, ensure its internal antenna is properly extended if the signal is weak.
5.3. Charging
5.3.1. Bait Boat Battery Charging
- Connect the USB charging cable to the boat's charging port (or directly to the battery if removable).
- Connect the other end of the USB cable to a suitable USB power adapter (not included) or a computer USB port.
- The charging indicator light will turn red during charging.
- The light will turn off once charging is complete.
5.3.2. Remote Control & Fish Finder Remote Charging
- Use the provided Type-C charging cables for the respective remote controls.
- Connect to a 5V 1A charging adapter or a computer USB port.
- Follow the indicator lights on each remote for charging status (typically red for charging, off/green for full).
5.4. Fish Finder Setup
5.4.1. Sonar Transmitter Usage Scenario
The sonar transmitter is integrated into the bait boat. When the boat is in water, the sonar signal is emitted downwards. The signal reflects off the bottom and any fish, and the reflected signal is wirelessly transmitted to the fish finder remote control for display.
5.4.2. Powering On the Fish Finder Remote
Long press the Power/Menu key on the fish finder remote to turn it on. It will enter user mode directly. You can switch between