ASAIR AMS2000

Contents

ASAIR AMS2000 Mass Flow Meter User Manual

Model: AMS2000

1. Introduction

The ASAIR AMS2000 is a thermal mass flow meter designed to accurately calculate the mass flow of gas by measuring changes in resistance. It incorporates a self-developed MEMS mass flow chip, offering ease of use, high accuracy, high stability, high and low temperature resistance, good linearity, and fast response time. Each AMS2000 mass flow controller undergoes calibration for range, accuracy, repeatability, and response time prior to delivery.

ASAIR AMS2000 Mass Flow Meter, front view
Figure 1: ASAIR AMS2000 Mass Flow Meter

2. Safety Information

Please read and understand all safety instructions before installing or operating the device. Failure to follow these instructions may result in injury or damage to the product.

  • Carefully remove the product from its packaging. Do not use excessive force or allow the device to collide with hard surfaces, as this may cause damage.
  • Ensure the power supply voltage matches the device's requirements (9-24V DC).
  • Do not attempt to disassemble or modify the device. Refer all servicing to qualified personnel.
  • Operate the device within its specified environmental conditions (e.g., temperature, pressure).

3. Product Overview

The AMS2000 Mass Flow Meter features a compact design with an integrated LCD display and control buttons for easy interaction. It is designed for various gas measurement applications.

Key Features:

  • Mass flow and temperature measurement
  • MODBUS RTU communication
  • Wide power supply range: 9~24V DC
  • High repeatability and stability
  • Integrated LCD display for real-time data
ASAIR AMS2000 Mass Flow Meter with LCD display
Figure 2: Top view of the AMS2000 with LCD display
ASAIR AMS2000 Mass Flow Meter with display and control buttons
Figure 3: Side view showing display and control buttons

4. Specifications

Parameter Value
Model Number AMS2000
Product Name Mass flow controller
Description mass flow meter
Measurement Range 0~200L/min (standard)
Accuracy ±3%FS
Power Supply 9~24V DC
Display LCD
Max Working Pressure 0.8MPa
Communication Mode RS485
Material Metal, Resin
Installation Method Self-contained
Mounting Type Screw
Measure Temperature 0~50℃
Detailed specifications, dimensions, and interface definition for AMS2000
Figure 4: Detailed Specifications and Dimensions

5. Setup and Installation

The AMS2000 Mass Flow Meter is designed for self-contained installation using screws. Follow these steps for proper setup:

  1. Unpacking: Carefully remove the device from its packaging. Avoid any forceful impacts or collisions that could damage the unit.
  2. Mounting: Secure the flow meter in the desired location using appropriate screws. Ensure the mounting is stable and free from vibrations.
  3. Flow Direction: Observe the 'FLOW' arrow indicated on the device to ensure correct orientation with the gas flow.
  4. Electrical Connection: Connect the power supply and communication lines according to the interface definition.

Electrical Interface Definition:

ASAIR AMS2000 Mass Flow Meter rear view with wiring diagram label
Figure 5: Rear view with wiring diagram label
Pin No. Description
① RS485B
② RS485A
③ DC 9-24V
④ GND

Ensure all connections are secure before applying power.

6. Operation

The AMS2000 features an LCD display and control buttons for monitoring and configuration.

Initial Power-Up:

Once powered, the LCD will display the current mass flow rate and temperature. The default display shows standard liters per minute (Std L/min) and temperature in degrees Celsius.

Using the Control Buttons:

The device typically includes buttons for navigation (e.g., Up, Down) and selection/setting (e.g., 'S' or 'Set'). These buttons allow users to:

  • View different measurement parameters.
  • Access and modify device settings (e.g., communication address, baud rate for RS485).
  • Perform calibration adjustments if necessary (advanced users only).

Refer to the official user manual PDF for detailed instructions on menu navigation and parameter configuration.

MODBUS RTU Communication:

The AMS2000 supports MODBUS RTU communication via its RS485 interface. This allows for remote monitoring and control of the device using a compatible MODBUS master device. Consult the official user manual PDF for the MODBUS register map and communication protocol details.

7. Maintenance

  • Cleaning: Keep the exterior of the device clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Inspection: Periodically inspect the connections and wiring for any signs of wear or damage.
  • Environmental Conditions: Ensure the operating environment remains within the specified temperature and pressure ranges to maintain optimal performance and longevity.
  • Recalibration: While the device is factory calibrated, periodic recalibration may be required depending on application and accuracy requirements. Consult a qualified technician for recalibration services.

8. Troubleshooting

If you encounter issues with your AMS2000 Mass Flow Meter, consider the following basic troubleshooting steps:

  • No Display/Power: Check the power supply connections and ensure the DC 9-24V input is correct. Verify the power source is active.
  • Incorrect Readings: Ensure the flow meter is installed in the correct flow direction. Verify that the gas being measured is compatible with the device's specifications. Check for any blockages in the flow path.
  • Communication Issues (RS485): Verify the RS485 wiring (A to A, B to B) and ensure the communication parameters (baud rate, parity, stop bits, device address) are correctly configured on both the flow meter and the MODBUS master.
  • Device Damage: If physical damage is observed or suspected, discontinue use and contact support.

For more detailed troubleshooting, refer to the official user manual PDF.

9. User Tips

No specific user tips were available from reviews or Q&A for this product. However, general best practices for mass flow meters include:

  • Always ensure the gas being measured is clean and free of particulates to prevent sensor fouling.
  • For critical applications, consider installing a filter upstream of the flow meter.
  • Regularly log data to establish a baseline and easily identify deviations in flow or performance.

10. Warranty and Support

For detailed warranty information, technical support, or service inquiries, please refer to the official user manual or contact the manufacturer/seller directly. The official user manual in PDF format can be accessed via the following link: ASAIR AMS2000 User Manual (PDF).

You may also find additional support resources or contact information in the product video below:

Product video, includes contact information for support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.