Introduction
The TOPPING DX1 II is a versatile Digital-to-Analog Converter (DAC) and Headphone Amplifier designed to elevate your audio experience for both music listening and competitive gaming. This device features a high-performance ESS ES9039Q2M DAC chip, XMOS high-performance USB processing, and a powerful headphone amplifier output. It supports a wide range of connectivity options and advanced sound customization features like a 10-band high-precision Parametric Equalizer (PEQ).
This manual provides detailed instructions on setting up, operating, maintaining, and troubleshooting your DX1 II to ensure optimal performance and longevity.
What's in the Box
Please check the package contents upon unboxing. If any items are missing or damaged, please contact your retailer.
- TOPPING DX1 II Unit ×1
- Infrared Remote Control ×1
- USB A-C Cable ×1
- USB C-C Cable ×1
- Product Information Card ×1

Setup Guide
1. Rear Panel Overview
Familiarize yourself with the input and output ports on the rear panel of your DX1 II.

- USB Input & Power Input: Connects to your computer or tablet for audio data and power.
- SPDIF Optical Input (IN): For connecting digital audio sources like CD players, TVs, or game consoles.
- SPDIF Optical Output (OUT): For sending processed digital audio to another DAC or device.
- RCA Single-Ended Output (L/R): For connecting to active speakers or a power amplifier.
- 4.4mm Balanced Stereo Output: For connecting to balanced headphones or amplifiers.
- UAC Mode Switch (2.0 / 1.0): Toggles between USB Audio Class 2.0 (for high-resolution audio on Windows/macOS) and USB Audio Class 1.0 (for plug-and-play compatibility with devices like Nintendo Switch and PlayStation).
2. Connecting to a Computer/Tablet
- Using the provided USB A-C or USB C-C cable, connect the USB port on the DX1 II to a USB port on your computer or tablet. The DX1 II will draw power and receive audio data through this single connection.
- For Windows Users: For optimal performance and high-resolution audio playback, it is recommended to install the custom Thesycon USB driver. This driver can typically be found on the TOPPING official website.
- For macOS Users: The DX1 II operates driver-free on macOS.
- For Linux Users: The DX1 II typically operates driver-free on most Linux distributions.
3. Connecting Headphones
- 3.5mm Single-Ended Headphone Jack (Front Panel): Connect your standard headphones or gaming headsets (TRRS with microphone supported) to this port.
- 4.4mm Balanced Headphone Jack (Front Panel): Connect headphones with a 4.4mm balanced connector for enhanced power and audio quality.
4. Connecting to Speakers/Amplifiers
- RCA Single-Ended Output: Connect RCA cables from the DX1 II's RCA outputs to the input of your active speakers or power amplifier.
- 4.4mm Balanced Stereo Output: If your amplifier or active speakers support 4.4mm balanced input, you can use this output for a balanced connection.
5. Connecting Other Digital Audio Sources (Optical)
- Use an optical TOSLINK cable to connect your CD player, TV, or game console's optical output to the SPDIF Optical Input (IN) on the DX1 II.
6. UAC Mode Selection for Gaming Consoles
For plug-and-play compatibility with Nintendo Switch and PlayStation consoles:
- Ensure the DX1 II is disconnected from the console.
- Set the UAC Mode Switch on the rear panel to 1.0.
- Reconnect the DX1 II to your gaming console.

Operating Instructions
1. Front Panel Controls and Display

- Multi-function Knob: Rotate to adjust volume. Press to cycle through input sources or other settings (refer to remote control for full functionality).
- Display: Shows current volume level (in dB), active input (USB, Optical), Gain setting (Low/High), and selected EQ profile (EQ1, EQ2, EQ3).
- Headphone Jacks: 3.5mm single-ended and 4.4mm balanced outputs.
2. Infrared Remote Control
The DX1 II comes with an infrared remote control for convenient operation. No pairing is required.

- Power Button (
): Turns the device on or off. - Output Mode Switching (OUT): Cycles between Headphone, Line Out, and Preamp modes.
- Headphone Mode: Audio output is directed to the headphone jacks.
- Line Out Mode: Fixed level audio output is directed to the RCA and 4.4mm line outputs.
- Preamp Mode: Variable level audio output (controlled by volume knob) is directed to the RCA and 4.4mm line outputs.
- PCM Filter Switching (FIL): Cycles through eight different filter modes to match listening preferences.
- C Preset Keys (C1, C2, C3): For instant recall of stored PEQ settings, gain settings, and output modes. Useful for quickly switching between configurations for music, gaming, or movies.
- Gain Switching (G): Toggles between Low and High gain settings. High gain provides more power for demanding headphones, while Low gain is suitable for sensitive IEMs.
- EQ Selection (EQ): Freely switch among 3 preset EQ profiles (EQ1, EQ2, EQ3) or disable EQ (AUTO).
- Volume Up/Down (
): Adjusts the output volume.
3. Parametric Equalizer (PEQ) Customization
The DX1 II supports up to 10 bands of fully customizable PEQ adjustment. You can tailor the sound precisely using TOPPING's software tools.
- TOPPING Tune Software: This self-developed tuning algorithm allows you to precisely adjust frequency, gain, and bandwidth (Q factor) for each of the 10 bands, with independent left/right channel settings. You can import target curves, generate compensation, and save multiple profiles.
- TOPPING Home Web Platform: This platform offers a visual drag-and-drop PEQ interface, making it easier to create and manage your ideal PEQ settings. You can also apply EQ files shared by other users and share your own profiles.


Maintenance and Care
- Cleaning: Use a soft, dry cloth to wipe the exterior of the DX1 II. Avoid using abrasive cleaners, solvents, or chemical sprays, as these can damage the finish.
- Storage: When not in use for extended periods, store the DX1 II in a clean, dry place away from direct sunlight, high temperatures, and humidity.
- Cable Care: Handle USB and audio cables gently. Avoid sharp bends, kinks, or excessive pulling, which can damage the internal wires.
- Environmental Conditions: Protect your device from extreme temperatures and high humidity. These conditions can negatively impact internal components and the longevity of the device.
Troubleshooting
No Sound Output
- Check all cable connections: Ensure USB, headphone, and line-out cables are securely connected.
- Verify power: Confirm the DX1 II is powered on (indicated by the display).
- Check volume levels: Ensure the volume on the DX1 II and your source device (computer, tablet) is not muted and is set to an audible level.
- Input selection: Make sure the correct input (USB or Optical) is selected on the DX1 II.
- Driver/Software: For Windows, ensure the USB driver is correctly installed and your audio output is set to "TOPPING DX1 II" in your system sound settings.
- Headphone connection: Ensure headphones are fully plugged into the correct jack (3.5mm or 4.4mm).
Distorted or Low Volume Sound
- Volume levels: Adjust the volume on both the DX1 II and your source device. Avoid setting either to maximum, which can sometimes cause distortion.
- Gain setting: Ensure the gain setting (Low/High) is appropriate for your headphones. High-impedance headphones may require High gain.
- Source quality: Test with different audio files or sources to rule out issues with the audio content itself.
- Cable integrity: Inspect USB and audio cables for damage or loose connections.
Intermittent Sound or Static
- Cable connections: Re-seat all cables. Try different USB ports on your computer.
- Cable quality: Try using a different USB cable to rule out a faulty cable.
- Interference: Keep the DX1 II away from other electronic devices that might cause electromagnetic interference.
Microphone Not Working (with TRRS Headset)
- Headset compatibility: Ensure your TRRS headset is fully compatible with the 3.5mm jack standard.
- System settings: Check your computer's sound settings to ensure the microphone input is correctly selected and not muted.
- Headset integrity: Test the headset on another device to confirm its microphone is functional.
Device Not Recognized by Computer
- USB port: Try connecting to a different USB port on your computer.
- USB cable: Use a different USB cable.
- UAC mode: Ensure the UAC mode switch is set correctly (2.0 for most computers, 1.0 for specific consoles).
- Restart: Restart your computer and the DX1 II.
Specifications
General Specifications
| Feature | Specification |
|---|---|
| Model Number | TOPPING DX1 II |
| Type | Desktop DAC & Headphone Amplifier |
| Material | Metal |
| Dimensions (W x H x D) | 21 x 15 x 6.5 cm (approximate) |
| Power Input | USB-C (5V) |
| UAC Modes | UAC 1.0 & 2.0 (switchable) |
| EQ | 10-band high-precision PEQ (TOPPING Tune) |
DAC Specifications (Line Out/USB In@96kHz)
| Parameter | RCA SE | 4.4mm BAL |
|---|---|---|
| DAC Chip | ESS ES9039Q2M | |
| USB Controller | XMOS XU316 | |
| PCM Support | Up to 32-bit / 384kHz | |
| DSD Support | DSD256 (DoP) | |
| THD+N @1kHz (A-wt) | <0.00009% | <0.00007% |
| THD @20-20kHz (90kBw) | <0.0008% | <0.0005% |
| SNR @1kHz (A-wt) | 125dB | 128dB |
| Dynamic Range @1kHz (A-wt) | 125dB | 128dB |
| Frequency Response | 20Hz-20kHz (±0.1dB) | 20Hz-20kHz (±0.1dB) |
| Output Level | 2.4Vrms @0dBFS | 5.1Vrms @0dBFS |
| Noise (A-wt) | <1.3uVrms | <2.0uVrms |
| Channel Crosstalk | -126dB @1kHz | -140dB @1kHz |
| Channel Balance | 0.3 dB | 0.3 dB |
| Output Impedance | 100Ω | 100Ω |
| Output Coupling | DC | DC |
Headphone Amplifier Specifications (USB In@96kHz)
| Parameter | 3.5mm Headphone Jack | 4.4mm Headphone Jack |
|---|---|---|
| THD+N @1kHz (A-wt) | <0.00005% @Output=200mW(32Ω) <0.00015% @Output=22mW(300Ω) | <0.0010% @Output=850mW(32Ω) <0.0001% @Output=90mW(300Ω) |
| THD @20-20kHz (45kBw) | <0.0020% @Output=200mW(32Ω) <0.0003% @Output=22mW(300Ω) | <0.0050% @Output=850mW(32Ω) <0.0003% @Output=90mW(300Ω) |
| SNR @MAX OUT 1kHz (A-wt) | 125dB @1kHz | 128dB @1kHz |
| Dynamic Range @1kHz (A-wt) | 125dB @1kHz | 128dB @1kHz |
| Frequency Response | 20Hz-20kHz (±0.1dB) | |
| Output Level | 2.3Vpp @G=L, 11.5Vpp @G=H 0.8Vrms @G=L, 4.0Vrms @G=H 0.3dBu @G=L, 14.4dBu @G=H | 4.6Vpp @G=L, 23.0Vpp @G=H 1.6Vrms @G=L, 8.1Vrms @G=H 6.3dBu @G=L, 20.4dBu @G=H |
| Noise (A-wt) | <0.9uVrms @G=L <1.9uVrms @G=H | <1.2uVrms @G=L <2.3uVrms @G=H |
| Channel Crosstalk | -102dB @1kHz | -140dB @1kHz |
| Gain | G=L -1.4dB (Vrms/FS) G=H 12.4dB (Vrms/FS) | G=L 4.4dB (Vrms/FS) G=H 18.4dB (Vrms/FS) |
| Channel Balance | 0.3 dB | 0.3 dB |
| Output Impedance | <1Ω | <2Ω |
| Output Power | 800mW x 2 @16Ω THD+N<1% 510mW x 2 @32Ω THD+N<1% 260mW x 2 @64Ω THD+N<1% 130mW x 2 @150Ω THD+N<1% 29mW x 2 @600Ω THD+N<1% | 1000mW x 2 @32Ω THD+N<1% 1000mW x 2 @64Ω THD+N<1% 230mW x 2 @300Ω THD+N<1% 115mW x 2 @600Ω THD+N<1% |
| Load Impedance | >8Ω | >8Ω |
Note: All data above was measured by TOPPING Lab under DC 5V power supply.

User Tips
Based on user feedback, there are no specific usage tips available at this time. Users have noted discrepancies in product color received versus ordered. Please verify your order details upon receipt.
Warranty and Support
Warranty Information
For detailed warranty information, including coverage period and terms, please refer to the product packaging, the official TOPPING website, or contact your point of purchase. Keep your proof of purchase for any warranty claims.
Customer Support
If you encounter any issues or have questions not covered in this manual, please contact TOPPING customer support or your authorized dealer for assistance.