HITBOX HBC-65

Contents

HITBOX HBC-65 Plasma Cutter

Instruction Manual

1. Introduction

The HITBOX HBC-65 is a versatile digital plasma cutting machine designed for precision, efficiency, and ease of use. Featuring dual voltage compatibility (110V/220V) and advanced IGBT inverter technology, it delivers clean, efficient cuts on all electrically conductive materials. This manual provides essential information for the safe and effective operation, setup, and maintenance of your HBC-65 plasma cutter.

2. Safety Information

WARNING: Plasma cutting produces intense heat, UV radiation, and fumes. Always follow safety precautions to prevent injury or damage.

  • Eye Protection: Always wear a welding helmet with appropriate shade settings to protect your eyes from arc flash.
  • Body Protection: Wear flame-retardant clothing, gloves, and sturdy footwear to protect against sparks and molten metal.
  • Ventilation: Ensure adequate ventilation to remove fumes and gases produced during cutting. Work in a well-ventilated area or use fume extraction equipment.
  • Electrical Safety: Ensure the machine is properly grounded. Do not operate in wet conditions. Inspect cables for damage before each use.
  • Fire Hazards: Keep flammable materials away from the cutting area. Have a fire extinguisher readily available.
  • Air Supply: Ensure your air compressor is properly maintained and provides clean, dry air.
  • Non-High Frequency (Non-HF) Technology: This machine is designed with Non-HF technology to minimize electromagnetic interference (EMI) and reduce radiation, making it safer for sensitive environments and surrounding electronics.

3. Package Contents

Verify that all items are present in the package:

HITBOX HBC-65 Plasma Cutter package contents and dimensions

Figure 3.1: Package contents and machine dimensions (16.5in L x 6.3in W x 9.8in H, 13.96 lbs).

  • HITBOX HBC-65 Plasma Cutter Unit
  • Plasma Cutting Torch
  • Ground Clamp with Cable
  • Air Hose
  • Air Pressure Regulator with Filter
  • Consumables (electrodes, nozzles)
  • Power Adapter (if applicable)
  • Instruction Manual (this document)

4. Setup

4.1. Power Connection

The HBC-65 features automatic dual voltage adaptation (110V/220V, 50/60Hz). Connect the power cord to a suitable grounded electrical outlet. Ensure the circuit can handle the required amperage for your cutting needs.

4.2. Air Supply Connection

Rear view of HITBOX HBC-65 Plasma Cutter showing air regulator connection

Figure 4.1: Rear panel with air regulator and filter connection.

  1. Attach the included air pressure regulator and filter assembly to the air inlet port at the rear of the plasma cutter.
  2. Connect your air compressor hose to the inlet of the air pressure regulator.
  3. Ensure the air compressor provides clean, dry, oil-free compressed air.
  4. Adjust the air pressure using the regulator knob to the recommended PSI for your cutting application (e.g., 50 PSI for 110V, 60 PSI for 220V).
  5. The machine can also connect to an external air source for enhanced airflow control in heavy-duty applications.

4.3. Torch and Ground Clamp Connection

  1. Connect the plasma cutting torch cable to the designated port on the front panel of the machine. Ensure it is securely fastened.
  2. Connect the ground clamp cable to the ground terminal on the front panel.
  3. Attach the ground clamp securely to the workpiece, ensuring good electrical contact. The ground clamp must be attached directly to the metal being cut, not to painted or rusted surfaces.

5. Operating Instructions

5.1. Control Panel Overview

Close-up of HITBOX HBC-65 Plasma Cutter LED screen and controls

Figure 5.1: Large LED screen displaying current (A), air pressure (PSI), voltage (110V/220V), and mode indicators.

The large LED screen provides clear readings for current (A), air pressure (PSI), and selected voltage. Control buttons allow selection of various functions:

  • AIR: Indicates air flow status.
  • CUT: Plasma cutting mode.
  • PILOT ARC: Activates the non-touch pilot arc feature.
  • POST AIR: Adjusts the post-flow air time to cool the torch and extend consumable life.
  • 2T/4T: Torch trigger modes.
  • GRID: Specific mode for cutting mesh or grates.
  • CNC: Enables compatibility with CNC cutting tables.
  • MODE Button: Cycles through different operational modes.
  • SET TIME Button: Adjusts time-based parameters like Post Air or Pilot Arc duration.
  • OPERATE Knob: Adjusts cutting amperage.

5.2. Basic Cutting Procedure

  1. Ensure all connections (power, air, torch, ground) are secure.
  2. Turn on the plasma cutter.
  3. Set the desired cutting amperage using the OPERATE knob based on material type and thickness.
  4. Adjust air pressure using the external regulator to the recommended PSI.
  5. Select the appropriate mode (e.g., CUT, PILOT ARC).
  6. Position the torch nozzle a small distance (approx. 1/8 inch) from the workpiece for non-touch pilot arc operation.
  7. Press the torch trigger to initiate the arc. The pilot arc will establish without touching the metal.
  8. Move the torch steadily along the cutting line. Maintain a consistent speed for a clean cut.
  9. Release the trigger to stop cutting.

5.3. Non-Touch Pilot Arc Technology

Pilot Arc Cutting demonstration with cut samples

Figure 5.2: Pilot Arc Cutting reduces electrode burning and extends service life. Shows 1/2" (12mm) clean cut at 110V, 35A @ 50PSI and 1" (25mm) severance cut at 220V, 65A @ 60PSI.

The non-touch pilot arc allows for arc ignition without direct contact with the workpiece. This is beneficial for cutting painted, rusted, or dirty metals, as it reduces tip wear and provides a smoother start. The PILOT ARC function allows you to set the pilot arc duration (PA function) via the SET TIME button; longer durations are useful for cutting mesh metal, while shorter durations extend consumable life.

5.4. 2T/4T Function

  • 2T (Two-Touch) Mode: Press and hold the trigger to cut, release to stop. This is standard for short cuts.
  • 4T (Four-Touch) Mode: Press and release the trigger to start cutting, press and release again to stop. This mode is ideal for longer cuts as it reduces finger fatigue.

5.5. Post Air Time (Post Gas Time)

The POST AIR function allows you to set a delay for the air flow after the arc has stopped. This cools the torch head and extends the life of consumables. Adjust the post-flow time using the SET TIME button.

5.6. CNC Functionality

Plasma cutter working with a CNC cutting table

Figure 5.3: The HBC-65 can be integrated with CNC cutting tables for automated precision cutting.

The HBC-65 is equipped with CNC functionality, allowing it to be connected to and controlled by a CNC cutting table for automated and precise cutting operations. Refer to your CNC table's manual for specific connection and operation details.

5.7. MMA Welding (Stick Welding)

The HBC-65 also supports MMA (Manual Metal Arc) welding. While specific details for MMA operation are not extensively provided, ensure you have the correct electrode holder and ground clamp for welding, and adjust current settings appropriately for the electrode type and material thickness. Consult a general MMA welding guide for best practices.

6. Maintenance

6.1. General Cleaning

  • Regularly clean the exterior of the machine with a dry, soft cloth.
  • Keep the cooling vents clear of dust and debris to ensure proper airflow and prevent overheating.
  • Periodically open the machine (if comfortable and knowledgeable) to blow out internal dust with compressed air, ensuring power is disconnected first.

6.2. Torch Consumables

The performance of your plasma cutter heavily relies on the condition of its consumables (electrode, nozzle/tip, swirl ring, shield cap). Inspect them regularly and replace when worn.

  • Electrode: Replace when the emitter (hafnium insert) is pitted or eroded to about 1/16 inch (1.5 mm) deep.
  • Nozzle/Tip: Replace when the orifice becomes oval, enlarged, or shows signs of excessive spatter.
  • Swirl Ring: Replace if cracked or damaged, as it controls the gas flow pattern.
  • Shield Cap: Replace if cracked or heavily spattered, as it protects the nozzle.

6.3. Air Filter Maintenance

The air filter on the regulator removes moisture and particulates from the compressed air. Periodically check the filter bowl for accumulated water and drain it. Replace the filter element if it becomes clogged or discolored.

7. Troubleshooting

ProblemPossible CauseSolution
No arc when trigger is pressedNo power; Ground clamp not connected; Worn consumables; Insufficient air pressureCheck power supply; Ensure ground clamp has good contact; Replace consumables; Check air pressure and compressor
Poor cut quality (rough, dross)Incorrect amperage/speed; Worn consumables; Incorrect air pressure; Dirty materialAdjust amperage/speed; Replace consumables; Adjust air pressure; Clean workpiece
Arc cuts out during operationOverheating (thermal overload); Low air pressure; Loose connectionsAllow machine to cool; Check air supply; Secure all connections
Machine turns on but no displayInternal faultContact support

8. Specifications

ParameterDetails
ModelHBC-65
Input Voltage110V/220V (Auto-switching)
Frequency50/60Hz
Output Current (Plasma)20–65A
Duty Cycle40% @ 65A
Arc StrikingNon-Touch Pilot Arc (Non-HF)
Max Clean Cut Thickness1/2" (12.7mm)
Max Severance Cut ThicknessUp to 3/4" (19mm)
Cutting Speed (Plasma)6500mm/min
Power (kW)1000W
MaterialStainless Steel
Weight9.6KG (21.16 lbs) / Package Weight: 12.0KG (26.45 lbs)
Dimensions (L x W x H)16.5in x 6.3in x 9.8in (approx. 42cm x 16cm x 25cm)
Protection FeaturesOvercurrent, Overvoltage, Overheating, Overload

9. User Tips

  • Clean Air is Crucial: Always ensure your air compressor provides clean, dry air. Moisture in the air supply is a common cause of poor cut quality and reduced consumable life.
  • Experiment with Settings: Different materials and thicknesses require varying amperage and travel speeds. Start with recommended settings and make small adjustments to find the optimal combination for your specific task.
  • Maintain Consumables: Regularly inspect and replace worn torch consumables. This is the single most important factor for consistent cut quality and machine longevity.
  • Proper Grounding: A clean, direct connection for the ground clamp to the workpiece is essential for stable arc performance.

10. Warranty and Support

The HITBOX HBC-65 Plasma Cutter comes with a 1-year quality support warranty from the date of purchase. Please retain your proof of purchase for warranty claims.

For technical assistance, troubleshooting beyond this manual, or warranty service, please contact HITBOX customer support.

© 2023 HITBOX. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.