1. Important Information & Before Use
Thank you for purchasing the ROBORE X5FD Walking Pad Treadmill. Before using this product, please read all important instructions and precautions in this manual carefully to ensure safe and correct operation.
If you encounter any issues such as damage during transportation, missing parts, error code display, or malfunctions, please contact customer support at service_sports@163.com. Please provide your order number and details of the product issues, attaching relevant images or videos if applicable.
2. Safety Precautions
Please read the following icons and instructions carefully to use the product safely and correctly.
| Icon | Meaning | Specific Precautions |
|---|---|---|
| ⚠️ | Warning |
|
| ❌ | Prohibited |
|
| ❗ | Caution |
|
3. Product Diagram and Parts List
Product Diagram
Parts List
Before assembly, please check that all parts are included in the package.
| No. | Name | Qty |
|---|---|---|
| 1 | Running Deck | 1 |
| 2 | Handrail | 2 |
| 3 | Phone Holder | 1 |
| 4 | Remote Control | 1 |
| 5 | M8 Flat Washer | 4 |
| 6 | M8 Curved Washer | 4 |
| 7 | M8 × 55 Button Head Socket Cap Screw | 4 |
| 8 | M8 Hex Lock Nut | 4 |
| 9 | φ8 × 50 Ball Lock Pin | 2 |
| 10 | Silicone Hole Plugs | 2 |
| 11 | Multifunctional Screwdriver | 1 |
| 12 | 5mm Hex Wrench | 1 |
| 13 | M8 × 20 Knob | 2 |
| 14 | Safety Key | 1 |
| 15 | Safety Key Cord Clip | 1 |
4. Assembly Instructions
⚠️ Assembly work must be performed by two or more adults.
Step 1: Unpacking and Part Check
- Before assembly, ensure all parts listed in Section 3 are included.
Step 2: Handrail Frame Assembly
- Adjust the handrail frame to the desired angle.
- Attach the two knobs (13) to the holes on both sides of the treadmill and tighten them to secure the handrail frame.
- Insert the two silicone hole plugs (10) into the matching holes as shown.
Note: The knobs are for positioning only (prevents the frame from shaking). It is normal if they do not tighten fully.
Step 3: Phone Holder Installation
- Insert the phone holder (3) into the matching slots on the upper housing.
Step 4: Handrail Attachment
- Attach both handrails (2) to the handrail frame using button head socket cap screws (7), curved washers (6), flat washers (5), and hex lock nuts (8). Use two sets per side as shown in the drawing.
- Tighten all fasteners securely.
Safety Key Installation
- Place the small round end of the safety key (14) onto the corresponding position on the motor cover.
- Attach the safety key cord clip (15) to one side of the handrail frame as shown.
- Open the clip, pass the safety key cord through it, then close the clip to secure the cord.
- Attach the clip on the other end of the safety key to your clothing. Ensure the safety key is properly secured before operating the treadmill.
5. Incline Adjustment Method
- Pull the front support plates on both sides outward.
- Adjust the running deck (1) to the desired angle.
- Insert the two ball lock pins (9) into the corresponding holes on both sides to lock it in place.
Incline Level Selection:
There are four adjustment holes on each side of the treadmill, numbered 1 to 4 (from highest to lowest incline). Always ensure that the same numbered hole is selected on both sides to keep the running deck level and stable.
How to Move the Treadmill
- Remove the ball lock pins (9) and adjust the running deck (1) to the lowest incline.
- Reinsert the pins into the corresponding holes on both sides of the frame, as shown in the drawing.
6. Operating Instructions
Remote Control Operation
- Step 1: Turn on the power switch of the treadmill.
- Step 2: In standby mode, press the "" key to enter three countdown modes: Time, Distance, and Calorie. During mode selection, the indicator light for the current mode will remain on. Then select one of the desired modes and press "+" or "-" to increase or decrease the value of the countdown function.
- Step 3: After setting the countdown value, press "ON/OFF" to start the operation.
- Step 4: When you want to exit the countdown function mode, press "ON/OFF" again to stop.
Note: The images are for reference only. The actual remote control may differ from the images due to variations in production batches.
7. Exercise Guidelines
- Warm-up: Before using the unit, perform a 5-10 minute warm-up.
- Breathing: Do not hold your breath during exercise. Coordinate your breathing with your movements. If breathing becomes too labored, stop exercising immediately.
- Frequency: Allow 48 hours of rest between training the same muscle groups. Train the same groups every other day.
- Load: Determine training intensity based on your individual physical condition, following the principle of progressive overload. Muscle soreness is normal at the start of training and will subside as you continue.
- Diet: Wait at least 1 hour after meals before exercising. After training, wait at least 30 minutes before eating. Avoid excessive water consumption at once to prevent burdening your heart and kidneys.
- Stretching Exercises: It is advisable to perform stretches first. Warm up for 5-10 minutes, then perform the following 5 stretches. Hold each stretch for 10 seconds or more per leg, and repeat them again at the end of your workout.
Stretching Examples:
- Forward Bend Stretch: Bend knees slightly, slowly bend forward, relax back and shoulders, and reach for toes. Hold 10-15 seconds, relax. Repeat 3 times.
- Hamstrings Stretch: Sit on a mat, extend one leg, bend the other leg inward. Reach for toes with hands. Hold 10-15 seconds, relax. Repeat 3 times per leg.
- Calf and Achilles Tendon Stretch: Place hands on a wall/table, step one leg back, keep back leg straight, heel flat. Lean weight forward. Hold 10-15 seconds, relax. Repeat 3 times per leg.
- Quadriceps Stretch: Use right hand to balance on wall/table, reach back with left hand, grab left ankle, pull toward glutes. Hold 10-15 seconds for full stretch. Relax. Repeat 3 times per leg.
- Adductors Stretch (Inner Thigh Muscles): Sit with soles of feet together, knees outward. Hold feet with both hands, pull toward body. Hold 10-15 seconds, relax. Repeat 3 times.
8. Maintenance
Running Belt Adjustment Method
This product allows you to adjust the tension of the running belt by turning the belt adjustment bolts located at the rear part of the running deck.
Check:
Turn on the power, run the belt at a speed of approximately 2-3 MPH, and check if it runs straight.
⚠️ Please perform the adjustment with the power turned off and the plug unplugged.
Adjustment Tips:
For each adjustment, turn no more than a 1/4 rotation. After adjustment, turn on the power, run it at low speed, and check the condition.
Case 1: If the belt is shifting to one side
Symptom: The belt shifts left or right, rubs against the main unit frame, and produces abnormal noise.
- Check the deviation direction: Observe which direction the belt is shifting.
- Tighten the opposite side: If the belt shifts to the right, use a hex wrench to turn the left adjustment bolt clockwise by 1/4 rotation and tighten it. If it shifts to the left, turn the right adjustment bolt clockwise by 1/4 rotation and tighten it.
Case 2: If the belt slips or pauses
Symptom: While walking or running, the belt slips under your feet, or the belt stops even though the motor is running.
- Tighten both sides evenly: Use a hex wrench to tighten the left and right adjustment bolts at the rear part of the main unit evenly, turning each clockwise by 1/4 rotation at a time.
- Check: Run the treadmill at a low speed and check whether the slipping is resolved.
- Repeat: If the slipping persists, repeat evenly tightening both sides.
Case 3: If the belt is over-tightened
Symptom: The belt is extremely tight with no slack, and the motor appears overloaded.
- Loosen both sides evenly: Use a hex wrench to loosen the left and right adjustment bolts at the rear part of the main unit evenly, turning each counterclockwise by 1/4 rotation at a time.
- Check the slack: After adjustment, when the unit is stopped, lift the center of the belt and check if it rises about 3 cm to verify proper tension.
- Repeat: If the tension is too tight, repeat this process.
For a detailed video of the adjustment method, please refer to the QR code provided in the original manual.
9. Troubleshooting
| Error Code | Error Description | Cause | Recommended Action |
|---|---|---|---|
| E01 | Connection Error |
|
|
| E02 | Motor Damaged |
|
|
| E05 | Over-current Protection |
|
|
| E06 | Motor Over-voltage Protection |
|
|
| --- or ---- | Connection Error (Safety Lock) |
|
|
10. Specifications
| Item | Specification |
|---|---|
| Brand Name | ROBORE |
| Model Number | X5FD |
| Application | Home Use Treadmill |
| Color | Black |
| Speed | 1–10 km/h (0.6-6.3 MPH) |
| Incline | 0–40% Real Incline |
| Motor | 3.0 HP Brushless Motor |
| Noise Level | <45 dB |
| Maximum Load Capacity | 159 kg (350 LBS) |
| Folded Height | 15.5 cm |
| Running Belt Length | 80-120 cm |
| Running Belt Width | 30-50 cm |
| With Speakers | No |
| Bluetooth Connection | No |
| With Vibration Mode | No |
| Adjustable Slope | Yes |
| Screen | Yes |
| Heart Rate Test | HandHeld |
| Driving Power | Electric |
| Function | Monofunctional |
| Fold | Yes |
| Training Site | Legs, Foot |
| Type of Sports | Cardio Training |
| Origin | Mainland China |
| Rated Voltage | 220-240 V |
| Frequency | 50 Hz |
| Product Weight | 26 kg |
| Package Weight | 29.3 kg |
| Product Size (L x W x H) | 132 × 62 × 130 cm |
| Package Size (L x W x H) | 127 × 61 × 16 cm |
| Package Contents | 1 x Treadmill, 1 x User Manual |
11. User Tips
No specific user tips were available from provided reviews or Q&A content.
12. Warranty and Support
Warranty Coverage:
This product comes with a 1-year parts replacement warranty from the date of purchase. A purchase certificate (such as a receipt) is required when availing of the warranty. Please be sure to keep it.
Please dispose of this product in accordance with your local waste disposal regulations.
Customer Support:
For inquiries regarding this product or any support needs, please contact us via email:
E-mail: service_sports@163.com
- Professional customer service staff are available to answer your questions within 24 hours.
- Dedicated Maintenance Service: As a commitment to quality and durability, free maintenance tools are provided for orders placed within 6 months.
A PDF version of the user manual is also available for download. Please refer to the product page for the direct link to the PDF document.