ILIFE V5s Ultra

Contents

ILIFE V5s Ultra Robot Vacuum and Mop Combo

User Manual

1. Safety Information

Important Safety Instructions

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Remove hazards such as power cords, small items, or loose objects from the floor before cleaning.
  • Fold carpet tassels under the rug and lift hanging curtains or tablecloths off the floor.
  • For staircases or elevated areas, test whether the robot detects edges. Use barriers if necessary.
  • Use only manufacturer-recommended accessories and original rechargeable battery and charging dock.
  • Ensure the voltage matches the specifications on the charging dock.
  • This device is for indoor home use only. Do not use outdoors or in commercial environments.
  • Do not use water to rinse the device or wipe it with a wet cloth.
  • Do not operate the robot on wet or flooded surfaces.
  • Do not use near open flames or fragile items.
  • Keep hair, fingers, and loose clothing away from moving parts and openings.
  • Do not vacuum hard, sharp, flammable, or burning objects.
  • Do not use a damaged charging dock or power cord.
  • Keep the power cord away from heat sources and do not allow the robot to run over it.
  • If the power cord is damaged, have it replaced by a qualified technician.
  • Ensure the dustbin and filter are installed correctly before use.
  • Do not operate in a room where an infant is sleeping.
  • Stop using the device if it has been dropped, damaged, exposed to water, or used outdoors. Contact customer service.
  • Not suitable for high-pile carpets or certain dark-colored carpets.

Danger – Critical Safety Warnings

  • Disconnect the product from power if not used for a long period.
  • Always unplug the charging adapter before maintenance.
  • WARNING: Non-rechargeable batteries must not be recharged.
  • WARNING: For the purposes of recharging the battery, only use the detachable supply unit (model: K12V190060G) provided with this appliance.
  • This product is equipped with a rechargeable battery with a capacity of 2400mAh.
  • This appliance contains batteries that are only replaceable by skilled persons.
  • If any battery leakage is found, stop using the product immediately and contact the after-sales service center for assistance.
  • Do not power the device via external switches or circuits controlled by utility services.
  • If the power cord is damaged, it must be replaced by the manufacturer or authorized agent.
  • Maintain at least 20 cm distance between the antenna and your body during operation.
  • Frequency bands: Bluetooth 2402–2480 MHz; Wi-Fi 2412–2472 MHz.
  • Maximum RF transmission power: Bluetooth <10 dBm (EIRP), Wi-Fi <20 dBm (EIRP).
  • Before discarding the product, power it off and remove the battery.
  • Dispose of batteries according to local regulations.
  • Do not incinerate the product or battery even if damaged.
  • Use the product only as described in this manual. ILIFE is not responsible for loss or injury from misuse.

2. What's in the Box

The ILIFE V5s Ultra package includes the following components:

Video: Unboxing the ILIFE V5s Ultra Robot Vacuum and Mop Combo, showing all included accessories.

ILIFE V5s Ultra Main Body
Main Body
Charging Dock
Charging Dock
Power Adapter
Power Adapter
Water Tank
Water Tank
Mopping Support
Mopping Support
Mop Cloth (x2)
Mop Cloth × 2
Remote Control
Remote Control
Cleaning Brush
Cleaning Brush
High Performance Filter
High Performance Filter
User Manual
User Manual
Side Brush (x2)
Side Brush × 2
AAA Battery (x2)
AAA Battery × 2

3. Specifications

SpecificationDetails
ModelV5s Ultra
Dimensions300 × 300 × 81 mm
Net Weight2.2 kg
Battery TypeLi-ion
Battery Capacity2400mAh
Charging TypeAuto Charging / Manual Charging
Charging Time< 350 minutes
Robot Runtime≥100 minutes
Dustbin Capacity0.3 L
Water Tank Capacity0.3 L
Robot Suction4000 Pa
Cleaning ModesAuto, Spot, Edge, Daily Schedule
Main Body Button TypeTouch Button
Control MethodsApp, Alexa and Google Assistant
Ability to Cross Obstacles≤ 20mm
Applicable GroundTile, Marble, Wood floor, Laminate floor, Carpet
Filter TypeHEPA
Voltage14.4 V
Power (W)40w
CertificationCE

Note: Specifications are subject to change without notice as we continuously improve our products.

Product Specifications Table
Detailed Product Specifications

4. Product Overview

Robot Components

Top view of robot vacuum with labels for Bumper, Start/Pause Button, Middle Cover
Top View: 1. Bumper, 2. Start/Pause Button, 3. Middle Cover
Bottom view of robot vacuum with labels for Cliff Sensors, Charging Pins, Side Brush, Battery Compartment, Front Wheel, Suck Passage, Side Wheels
Bottom View: 5. Cliff Sensors, 6. Charging Pins, 7. Side Brush, 8. Battery Compartment, 9. Front Wheel, 10. Suck Passage, 11. Side Wheels
Side view of robot vacuum with labels for Dustbin and Power Switch
Side View: 12. Dustbin, 13. Power Switch

Water Tank Assembly

Water Tank Assembly Diagram with labels for Rubber Plug, Water Inlet Plug, Handle, Weep Hole
Water Tank Components: 1. Rubber Plug, 2. Water Inlet Plug, 3. Handle, 4. Weep Hole

Note: When filled with water, the robot's ability to climb over obstacles may be slightly reduced.

5. Setup

5.1 Important Pre-Cleaning Notes

Frequent use helps the robot learn your home layout for more efficient path planning and reduced missed spots. Follow these guidelines before each use to protect your home and maximize the robot's cleaning efficiency:

  • Remove loose items from the floor: Clear cables, clothing, or small objects that could get tangled in the wheels or brushes.
  • Fold the rug's tassel trim underneath: Prevent tangling during cleaning. Avoid using on high-pile or thick rugs.
  • Block off dangerous zones: For areas like fireplaces, vents, or staircases, place physical barriers or set “No-Go Zones" in the app.
  • Avoid use on floor with excessive water: Avoid vacuuming large amounts of water as it will potentially damage the robot.
  • Obstacle height limit: The robot can climb over thresholds up to 12mm (0.47").
  • Cliff sensor limitations: Although the robot includes anti-drop sensors, performance may decrease on dark carpets or reflective surfaces, or in the situation the sensors get stained. Use physical barriers as needed.

5.2 Installing and Using the Charging Dock

Placement Guidelines

  1. Place the charging dock on a hard, flat surface against a wall.
  2. Ensure there are no obstacles within 2 meters in front and 1 meter on both sides.
  3. Avoid placing it in areas with strong sunlight or reflective surfaces.
  4. Keep it away from places where pets sleep to avoid noise disturbance.

Power Connection

Connect the adapter with the charging dock. Plug in the power cable. Once powered, the signal light of the dock will light up.

5.3 Charging the Robot

Two Charging Methods

  1. Plug into an outlet.
  2. Press the Home button on the remote control to make the robot return to the charging dock for automatic charging.

Proper Placement

Align the robot with the charging pins on the charging dock. When connected properly, all lights will pulse in a regular, rhythmic cycle. This distinctive breathing light pattern is your indicator that the robot is charging.

Charging Completes

When all lights stay on solid, it indicates that the battery has been fully charged. The robot will automatically enter sleep mode if no operation is detected within two minutes.

Note: Recharging the robot after each use helps extend battery life.

Important Notes for Charging

  • Make sure the charging pins on the robot and charging dock remain clean to avoid poor contact.
  • Store the robot on the charging dock with the charging dock powered on.
  • Before first use, charge the robot overnight. When charging is finished, display panel will turn off.
  • For long-term storage, fully charge the robot, turn it off and store it in a dry, ventilated place.

5.4 Installing and Using the Water Tank & Mop

Mounting bracket and mopping cloth

The mop bracket with mop should be on the robot when the water tank is used.

Fill the Water Tank

Open the rubber plug on the tank and fill with clean water. Tip: Use purified water to reduce limescale buildup. Reseal the plug tightly to prevent leakage.

Exploded view of water tank and robot
Water tank installation and water flow diagram for spotless floors.

Installing the Water Tank

Open the robot lid and put the water tank into the body, the weep hole of the water tank should be aligned with the weep hole on the robot body.

Start Mopping

Close the robot lid, press CLEAN button to start the wet cleaning. There is no vacuum suction function during the wet cleaning.

Important Notes for Mopping

  • Dustbin is for dry clean and water tank is for wet clean.
  • It is suggested to make the suction (dry clean) before wet clean for a better cleaning result.
  • Do not use the mop on carpets.
  • The water in the water tank flows out automatically, so it is prohibited to let water tank be still inside or outside of the robot when there is still water in the tank. This will cause water logging on the floor.
  • Please take out the water tank when you charge the robot vacuum cleaner.
  • After mopping, remove the mop and wash/dry it to avoid mildew or odors.

5.5 Using the ILIFE Clean App

Downloading the App

Scan the QR code or search for “ILIFE Clean” in your app store. The app supports 2.4GHz or dual-band 2.4GHz/5GHz networks but does not support 5GHz-only networks.

Wi-Fi Pairing Modes

The robot supports Bluetooth Pairing Mode and AP (Access Point) Pairing Mode.

Bluetooth Pairing Mode
  1. Go to your phone's settings, turn on Bluetooth and enable Bluetooth permission for ILIFE Clean app.
  2. Return to the ILIFE Clean app – the device will appear automatically and tap "Add" to begin.
  3. Select your 2.4GHz Wi-Fi network and enter the password to go next.
  4. The device starts downloading.
  5. Device is added successfully and done.
AP (Access Point) Pairing Mode
  1. In the app, choose your specific robot model.
  2. Choose your 2.4GHz Wi-Fi network and enter the password.
  3. Go to your phone's Wi-Fi settings and connect to a network that starts with "SmartLife". Return to the app once connected.
  4. Wait for the app to complete the device connection process.

6. Operating Instructions

6.1 Turning On the Robot

Turn on the power switch around the power socket. The display panel will flash. If no command is received, the robot will turn to sleeping mode after 10 minutes.

Note: Please always keep the power switch turned on. If not, the robot cannot work. If the power switch is turned off, all scheduling will be lost.

6.2 Remote Control Guide

Before using the remote, insert two AAA/R03 batteries. Remove the batteries if not used for a long time.

ButtonFunction
PowerStart or pause cleaning
DirectionIn standby mode: Forward, Left, Right (Not functional during running)
MAX ModeSwitch Suction Level by Each Press: Standard → Max → Standard
ScheduleTo enter schedule mode. To confirm cleaning schedule.
ClockTo enter clock mode. To confirm time setting.
Spot ModeDeeply cleans a 1.5m × 1.5m area in a spiral pattern
Edge ModeCleans along walls and furniture edges
HomeSend the robot back to the charging dock manually

6.3 Schedule Mode

To offer a complete automatic cleaning experience, the robot receives preset cleaning schedules. Set local time and schedules with the remote control. The robot will start cleaning automatically at the preset time every day.

Note: If the robot is not connected to the network, scheduled programs set via the remote control will be lost after a power outage. However, once the robot connects to the network and synchronizes with internet time, scheduled programs set at that point will be saved.

Setting Local Time with Remote Control

  1. Tap the Clock button. Remote control display will show and flashing 00:00.
  2. Adjust time with the direction buttons. To set local time, press “<” or “>” to change from hours to minutes.
  3. Press the Clock button to save local time. Successful setting will be confirmed by a "beep" sound.

Setting a Schedule

  1. Tap the Schedule button. Remote control display will show and flashing 00:00.
  2. Use direction buttons to adjust schedule time.
  3. Press the Schedule button to save a schedule. Successful scheduling will be confirmed by a “beep” sound. The robot will start working at the preset times.

Canceling a Schedule

Adjust the schedule time to "00:00" and save; or turn off the power switch on the robot.

  • Please pay attention to the prompt to see if the robot is successfully scheduled.
  • Rescheduling is required after changing batteries in the remote control.

6.4 Cleaning Modes

Diagram showing four cleaning modes: Auto, Max, Edge, Spot
Flexible Options for Different Cleaning Needs: Auto, Max, Edge, and Spot modes.
  • Auto Mode: The robot cleans in a systematic pattern for general cleaning.
  • Max Mode: Increases suction power for deeper cleaning.
  • Edge Mode: The robot cleans along walls and furniture edges.
  • Spot Mode: The robot cleans a specific area in a spiral pattern for concentrated cleaning.

6.5 Voice Activated Control

The ILIFE V5s Ultra is compatible with Amazon Alexa and Google Assistant, allowing you to start or stop cleaning with simple voice commands.

Robot vacuum with smart speaker showing voice commands
Hands-free Operation with Popular Voice Assistants.

7. Maintenance

Always turn off the robot and unplug the power adapter before performing maintenance.

ComponentClean FrequencyReplace Frequency
Mop ClothAs neededEvery 3-6 months
DustbinWeeklyN/A
FilterN/AEvery 1-1.5 months
Side BrushWeeklyEvery 3–6 months (or if damaged)
Side WheelsMonthlyN/A
Cliff SensorsMonthlyN/A
Charging ContactsMonthlyN/A

7.2 Cleaning the Dustbin and Filter

  1. To open the robot's (top) cover, press the button marked PUSH.
  2. Remove the dustbin and check if there is any debris in the suction inlet, and then clean it.
  3. Open the dustbin lid, Remove the primary filter.
  4. Empty the dustbin.
  5. Remove the high performance filter and rinse the dustbin with water.
  6. Clean the primary filter and the high performance filter with the cleaning brush.
  7. Replace the high performance filter if necessary and reinsert the dustbin.
  8. Wipe the dustbin dry with a clean cloth and reinstall it into the robot.

Note: A primary filter is replaceable and should be washed with water after having been in use for about 15-30 days, after which it should be dried in a cool and well-ventilated place and not to be squeezed. High performance filter cannot be cleaned with water. To prolong the life of the filter it can be cleaned by shaking the filter.

7.3 Cleaning the Water Tank and Mop Cloth

Mop Cloth

  1. Remove the mop bracket and peel off the cloth.
  2. Rinse with clean water and let it air-dry completely.

Water Tank

  1. Open the rubber plug and drain any leftover water.
  2. Wipe the tank clean and let it dry thoroughly.

7.4 Cleaning the Side Brushes, Side Wheels and Front Wheel

Side Brushes

  • Remove the screws and then remove the side brush, clean off the hair and other foreign objects tangled in it and wipe it off with a clean cleaning cloth.
  • When replacing the side brush, please distinguish the corresponding installation position of the "L" "R" side brush.

Side Wheels

Check and remove any obstructions caught in the wheels.

Front Wheel

Clean any hair and foreign objects tangled in the front wheel, and wipe it with a clean cleaning cloth.

7.5 Cleaning Sensors and Charging Pins

Cliff Sensors

Use a soft brush to gently clean the sensors on the underside of the robot.

Charging Pins

Wipe both the robot's and the charging dock's charging pins with a dry cloth to maintain charging efficiency.

7.6 Battery Care and Activation

For Long-Term Storage

  1. Charge the robot fully.
  2. Power it off.
  3. Store in a dry, ventilated place. Recharge every 3 months to avoid battery degradation.

Battery Activation (After Deep Discharge or Long Inactivity)

  1. Align the robot on the charging dock.
  2. Charge it for 3 minutes and then remove it away. Repeat this process 3 times.
  3. Then charge continuously for 5-6 hours until it is fully charged when the indicator turns off.

8. Troubleshooting

8.1 Error Codes (Short Tones)

The robot will remind you by beeping when it is malfunctioning.

NO.TonePossible CauseWhat to do
01•Wheels or side brushes or fan problems.Check and clean wheels, side brushes, and fans.
02••OBS or bumper sensor or cliff sensor failure.Check the bumper and OBS, and clean cliff sensor.
03•••Robot gets stuck.Move the robot.
04••••Gyro failure.Detect and clean the gyro, and move the robot.

8.2 Error Appearance

Error appearanceLikely causeSolution
Circle around a small areaSide wheels are jammedRemove hair and debris from side wheels. While reinstalling, push the wheels in and out to make sure they can rotate freely. Restart robot in another spot.
Keep moving backwardCliff sensor is dirty or brokenCheck cliff sensor lens. Clean or replace it if needed.
Bump into obstacles repeatedlyThe bumper is stuckTap the bumper 10-20 times to remove debris lodged in it. Loosen the screw of the bumper.
Working time shortenedBattery capacity dropped or robot is not fully chargedReplace battery or recharge robot.
CLEAN button light is off while chargingHair or small debris stuck in charging pins or robot not properly connected to charging pins.Clean charging pins or check if robot is connected to charging pins.
Pick up less dirt and debrisFilter is dirty or wetClean or replace filter.
Spit out litterDustbin is fullEmpty the dustbin.
Robot doesn't start at scheduled timeSchedule was not saved successfully, schedule was canceled after robot restart, power switch is off, battery is low, or debris jammed in components.Reset schedule. Wait for a beep to confirm completion of scheduling. Turn on power switch on robot. Keep the robot's power switch on and put it on charging dock to make sure robot is fully charged for the next job. Turn off the power switch on robot and empty the dustbin. Clean side brushes and suck passage.

Note: If all above solutions don't work, please take below actions:

  1. Re-set the robot by re-turning on the power switch.
  2. If restarting the robot still does not solve the problem, please send the machine to the after-sales center for repair.

9. User Tips

  • Scheduled Cleaning Resumption: The robot responds to scheduled cleaning once a day only. After recharging, it will start working automatically when the next schedule comes. If you need the robot to clean immediately, send a command with the remote control.
  • Continuous Cleaning: The vacuum will continue cleaning until you press PAUSE or its battery level is low, at which point it will return to the charging base.
  • Wet Floor Caution: The robot must not be used on wet floors. Vacuuming liquids will damage the robot.
  • Long-Term Charging: It is safe to leave the robot on the charging dock even when not in use. After fully charged, it enters trickle charging to prevent overcharge and battery self-discharge. Remember to turn off the power switch if storing for a very long time.

10. Warranty and Support

For more detailed information, please visit: www.iliferobot.com

If you encounter any issues with your robot, feel free to contact our customer service. For European customers, you can reach us at: warranty_repair_EU@iliferobot.com

You can also find the user manual in PDF format for download: ILIFE V5s Ultra User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.