APC SURT3000UXI-CH

Contents

APC Smart-UPS RT 3000VA 2700W 2U User Manual

Model: SURT3000UXI-CH

Brand: APC by Schneider Electric

1. Setup Instructions

This section guides you through the initial setup of your APC Smart-UPS RT 3000VA.

1.1 Unboxing and Inspection

Carefully remove the UPS from its packaging. Inspect the unit for any damage that may have occurred during shipping. If any damage is found, contact your dealer or APC immediately.

APC UPS in its shipping box
Figure 1: APC UPS in its shipping box, ready for unboxing.

1.2 Battery Connection

The UPS is shipped with the internal battery disconnected for safety. You must connect the battery before initial use.

  1. Locate the battery connection instructions, often found on a label near the battery compartment or on the rear panel.
  2. Follow the arrows or instructions to pull out the battery pack or rotate the battery connector.
  3. Ensure the battery connector is fully seated.
Rear view of APC Smart-UPS showing battery connection
Figure 2: Rear panel of the UPS, illustrating the battery connection point (often marked with a yellow pull tab or orange cover).

1.3 Placement and Mounting

The SURT3000UXI-CH is a 2U unit designed for both rack-mount and tower configurations.

  • Rack-Mount: Install the UPS into a standard 19-inch equipment rack using the provided rack-mounting hardware. Ensure adequate ventilation around the unit.
  • Tower: Use the included stands to position the UPS vertically for tower operation. Place it on a stable, flat surface.
APC UPS in a rack-mount configuration
Figure 3: APC UPS installed in a rack-mount setup.
APC UPS in a tower configuration with stands
Figure 4: APC UPS configured for tower placement using vertical stands.

1.4 Initial Power-Up

  1. Connect the UPS to a grounded utility power outlet using the provided input power cord.
  2. Press the power button on the front panel to turn on the UPS.
  3. Allow the UPS to charge its batteries for at least 24 hours before connecting critical equipment to ensure full runtime capability.

For a visual guide on unboxing and initial setup, refer to the video below:

Video 1: Unboxing and initial battery connection for an APC Smart-UPS. This video demonstrates how to unpack the unit and connect the internal battery, which is crucial for proper operation.

2. Operating Instructions

This section details how to operate your APC Smart-UPS RT 3000VA.

2.1 Front Panel Display and Controls

The front panel features an LCD display and control buttons for monitoring and managing the UPS.

Front view of APC Smart-UPS RT 3000VA showing display and controls
Figure 5: Front panel of the UPS, displaying current input voltage and operational status (Online).
  • LCD Display: Shows real-time status information such as input/output voltage, battery charge level, load percentage, and various alerts.
  • Control Buttons: Typically include Power On/Off, Menu Navigation (ESC, OK, Up, Down) for configuring settings and viewing detailed information.

2.2 Connecting Equipment

Connect your critical equipment to the output receptacles on the rear panel of the UPS. The SURT3000UXI-CH model typically features C13 and C19 outlets.

Rear panel of APC UPS showing C13 and C19 output receptacles
Figure 6: Close-up of the rear panel, showing multiple C13 output receptacles (10 Amp Max) and a C19 receptacle (16 Amp Max), along with overload protectors.
  • Ensure the total load connected does not exceed the UPS's rated capacity (2700W / 3000VA).
  • Connect servers, network devices, and other critical equipment that require uninterrupted power.
  • Avoid connecting laser printers or other high-surge devices to the battery-backed outlets, as they can overload the UPS.

2.3 Powering On/Off Connected Equipment

Once the UPS is online and providing power, you can power on your connected equipment. The UPS will provide battery backup in case of a power outage.

  • To power off the UPS and connected equipment, press and hold the power button until the unit shuts down.
  • For graceful shutdown of connected equipment, use the PowerChute software (if installed and configured) to initiate a controlled shutdown.

2.4 Voltage and Frequency Adjustment

The UPS can continuously adjust voltage and frequency to provide stable power to connected devices. This is typically an automatic function, but advanced settings may be accessible via the LCD menu or management software.

3. Maintenance

Regular maintenance ensures the longevity and optimal performance of your UPS.

3.1 Battery Replacement

The internal batteries have a finite lifespan. The UPS will typically indicate when battery replacement is due via the front panel display or alarms. Refer to the UPS documentation for specific battery replacement procedures. Always use genuine APC replacement battery cartridges (RBCs).

3.2 Cleaning

Keep the UPS clean and free from dust. Use a dry cloth to wipe the exterior. Ensure ventilation openings are not blocked by dust or debris.

3.3 Environmental Considerations

Operate the UPS within its specified environmental limits (temperature and humidity). Avoid placing the UPS near heat sources or in direct sunlight. Ensure proper airflow around the unit to prevent overheating.

4. Troubleshooting

This section provides solutions to common issues you might encounter with your UPS.

4.1 Common Issues and Solutions

Problem Possible Cause Solution
UPS does not turn on Battery not connected; No input power Ensure battery is fully connected. Check input power cord and wall outlet.
UPS beeps frequently On battery; Low battery; Overload Check utility power. Allow battery to charge. Reduce connected load.
Overload indicator active Too many devices connected Disconnect non-essential equipment. Check total load against UPS capacity.
Battery fault indicator active Battery needs replacement Perform a battery self-test. Replace battery if fault persists.

4.2 Protection Features

The APC Smart-UPS RT 3000VA is equipped with multiple protection features to safeguard your equipment and the UPS itself:

  • Lightning Protection: Protects against power surges caused by lightning strikes.
  • Short Circuit Protection: Prevents damage from short circuits in connected equipment.
  • Overvoltage Protection: Shields devices from excessively high input voltage.
  • Overcurrent Protection: Guards against excessive current draw.
  • Unbalanced Loads Protection: Ensures stable operation even with unevenly distributed loads across output phases (relevant for multi-phase systems, though this model is single phase, it maintains load balance internally).

5. Specifications

Feature Detail
Brand Name APC
Model SURT3000UXI-CH
Phase Single Phase
Protection Lightning/Short Circuit/Overvoltage/Overcurrent/Unbalanced Loads
Weight 14.45 kg (31.86 lb)
Electric Energy 2700 Wh
Max. Capacity Used 100%
Main Input Voltage 230 V
Other Input Voltage 220 V - 240 V
Rated Power (W) 2700 W
Rated Power (VA) 3000 VA
Number of Rack Units 2U
Package Length 73 cm
Package Width 56 cm
Package Height 29 cm
Package Weight 18.0 kg

6. Warranty and Support

Your APC Smart-UPS RT 3000VA comes with a manufacturer's warranty and access to support resources.

6.1 Warranty Information

This product is covered by a 24-month warranty from the date of purchase. The warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

6.2 Technical Support

For technical assistance, troubleshooting beyond this manual, or warranty service, please contact APC customer support. Refer to the official APC website for the most up-to-date contact information and support resources in your region.

7. User Tips

Here are some general tips to help you get the most out of your APC Smart-UPS:

  • Regular Self-Tests: Periodically initiate a battery self-test (usually via the front panel or management software) to ensure the batteries are functioning correctly.
  • Load Management: Monitor the load percentage displayed on the UPS. Keeping the load below 80% of the UPS's capacity can extend battery life and provide more runtime.
  • Software Installation: Consider installing APC PowerChute software on your connected servers. This software allows for graceful shutdown of operating systems during extended power outages, preventing data loss.
  • Environmental Control: Maintain a stable room temperature (ideally around 20-25°C or 68-77°F) to maximize battery lifespan. Extreme temperatures can significantly reduce battery performance and longevity.
  • Firmware Updates: Check the APC website periodically for firmware updates for your UPS model. Updates can improve performance, add features, or address known issues.

© 2023 APC by Schneider Electric. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.