Introduction
Thank you for purchasing the APEFOX Electric Scooter. This manual provides essential information for the safe operation, assembly, maintenance, and troubleshooting of your T90 Electric Scooter. Please read this manual thoroughly before use to ensure optimal performance and safety.
Important Safety Notice: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
A digital version of this user manual is available for download: User Manual (PDF)
Setup
Packing List
Carefully check the package contents. If anything is missing or damaged, please contact customer service at contact@apefox.com.
After verifying all components are present and in good condition, you can assemble your new Electric scooter.
Please retain the box and packaging materials in case you need to ship your Electric scooter in the future.
Remember to power off your Electric scooter and unplug the charging cable before assembling, mounting accessories, or cleaning the mainframe.
Always use both an electronic brake and a foot brake for emergency stops. Otherwise, you risk falls or collisions from not achieving the max braking capability.
Figure 1: Key features of the Apefox T90 Electric Scooter, including bright dual LED headlights, trigger throttle, high-brightness tail light, and IPX4 waterproof rating.
Assembly
- Unfold the Stem: Unfold the stem and push it until you hear a click. Flip up the folding pedal. Then unfold the kickstand to support the scooter.
- Attach the Handlebar: Attach the handlebar to the buckle, tighten the screws, and then install it aligned with the pole, making sure it is oriented correctly.
- Tighten Components: Tighten the screws on various components on the head.
- Adjust Riser Height: Use a hexagonal wrench to loosen the six screws and adjust the height of the riser.
Figure 2: Control Introduction and Function Description. This diagram illustrates the NFC and password unlock features, as well as the location of the front brake lever, light switch, trumpet, turn signal button, display, rear brake lever, accelerator, and on/off button.
Charging
Charging Steps:
- Open the charge port cover.
- Insert the charge plug.
- Close the charge port cover when finished.
WARNING: Do not connect the charger if the charge port or charge cable is wet. Do not charge or use your battery if it is damaged or shows traces of water. Your Electric scooter is fully charged when the LED on the charger changes from red (charging) to green (trickle charge). Close the charge port cover when not charging.
As with any electronic device, use a surge protector when charging to help protect your Electric scooter from damage due to power surges and voltage spikes. Do not use a charger from any other different product models.
Operating Instructions
Riding Safety
The Electric scooter is a recreational product. Before mastering riding skills, practice is necessary. The manufacturer is not responsible for any injuries or damage caused by rider inexperience or failure to follow instructions.
You can reduce risk by following all instructions and warnings, but you cannot eliminate all risks. Riding an Electric scooter carries risks of injury from loss of control, collisions, and falls. Always comply with local laws and regulations in public spaces. Faster speeds require longer braking distances. Sudden braking on low traction surfaces can lead to wheel slip or falls. Be cautious, maintain a safe distance, and slow down in unfamiliar areas.
- Always wear an approved helmet that fits properly with the chin strap in place, and provides protection for the back of your head.
- Do not attempt your first ride in areas with children, pedestrians, pets, vehicles, bicycles, or other obstacles and potential hazards.
- Respect pedestrians by yielding the right of way. Pass on the left when possible. When approaching from the front, stay to the right and slow down. Avoid startling pedestrians. When approaching from behind, announce yourself and slow down to walking speed when passing. Obey local traffic laws if different.
- In places without laws, comply with the safety guidelines in this manual. The manufacturer is not responsible for property damage, personal injury/death, accidents, or legal disputes caused by violations of safety instructions.
- Do not allow anyone to ride your Electric scooter unless they have carefully read this manual. Assist new riders until they are comfortable with basic operation. Ensure each new rider wears a helmet and other protective gear.
- Before each ride, check for loose fasteners and damaged components. If the Electric scooter makes abnormal sounds or signals an alarm, immediately stop riding. Contact contact@apefox.com for service.
- Be alert! Scan both far ahead and in front of your Electric scooter. Your eyes are your best tool for safely avoiding obstacles and low traction surfaces (including, but not limited to, wet ground, loose sand, loose gravel, and ice).
- To reduce the risk of injury, read and follow all "CAUTION" and "WARNING" notices. Do not ride at an unsafe speed. Never ride on roads with motor vehicles. The manufacturer recommends riders be 14+ years old.
People who should not ride the Electric scooter include:
- Anyone under the influence of alcohol or drugs.
- Anyone who suffers from a disease that puts them at risk if they engage in strenuous physical activity.
- Anyone who has problems with balance or with motor skills that would interfere with their ability to maintain balance.
- Anyone whose weight is outside the stated limits (see Specifications).
- Pregnant women.
- Riders under the age of 18 years old should ride under adult supervision.
- Comply with local laws and regulations when riding this product. Do not ride where prohibited by local laws.
- To ride safely, you must be able to clearly see what is in front of you and you must be clearly visible to others.
- Do not ride in the snow, in the rain, or on roads that are wet, muddy, icy, or that are slippery for any reason. Do not ride over obstacles (sand, loose gravel, or sticks). Doing so could result in a loss of balance or traction and could cause a fall.
- Do not attempt to charge your Electric scooter if the charger, or the power outlet is wet.
- Do not modify your Electric scooter. Modifications could interfere with operation, result in serious injury and/or damage, and void the Limited Warranty.
- Children should not play with the Electric scooter or parts of it, nor should cleaning or maintenance be done by children.
- Always place the Electric scooter on its stand on a flat and stable surface. Place with the stand against the slope to prevent tipping over. Never place with the front facing down the slope, as the stand may close and tip the machine. Check stability to avoid falling. Do not park in busy areas, but along a wall. If possible, park on flat ground.
- For a better driving experience, regular maintenance is recommended.
- Do not touch the brake system, it could cause injuries.
Instrument Introduction
Figure 3: Product Highlights, summarizing key features and specifications.
The instrument panel provides essential information and controls:
- Power button: Turns the scooter on/off.
- Mode switch button: Short press to toggle between ECO, SPORT, and COMFORT riding modes.
- Information switch button: Short press to toggle between TRIP, TIME, and ODO (odometer).
- Motor switch button: Short press to toggle between left motor, right motor, and dual motors.
- Start mode button: Short press to toggle between first gear (weak start), second gear (normal start), and third gear (strong start).
- Thumb throttle: Controls acceleration.
The display shows speed, gear, battery level, and other data. NFC unlock is available, and the vehicle comes with three NFC keys by default.
Menu Settings
When the display is on, press and hold buttons "3" and "5" simultaneously to enter the instrument function settings. In this interface, "4" and "5" are used for navigation (up and down), and "3" is used for confirmation. Pressing and holding buttons "3" and "5" simultaneously also exits the instrument function settings.
| Setting | Description |
|---|---|
| P01 | Backlight brightness, 1-10 |
| P02 | Mileage unit, 0:km 1:mile, 2:km mile full display |
| P03 | Voltage level, 24V 36V 48V 52V 60V 72V |
| P04 | Sleep time, 0: no sleep. Other numbers are sleep time, range: 1-60; Units in minutes |
| P09 | Zero start, non-zero boot setting, 0: zero start; 1: Non-zero boot |
| P16 | Instrument real-time cruise function: 0: No function; 1: There is this function |
| P19 | Taillight setting, 0: Taillight is always on; 1: Taillight is synchronized with headlights |
| P93 | Adjust the parameters to P93 to view the factory password 1234. Short press the No. 3 button to light up the "ENTER PASSWORD" icon on the main interface, which will stay on. The "88888" icon will flash 4 horizontal bars, prompting you to enter a 4-digit password. After entering, short press No. 3 again. If the "ENTER PASSWORD" icon stops flashing, the password is set successfully. To change it, repeat the steps. |
| P95 | Boot mode: 0: No password / No NFC; 1: There is NFC (Note: You can only boot with NFC. Pressing the boot button has no effect); 2: There is a password (4-digit password default 1234) / NFC |
Learning to Ride
- Wear an approved helmet and other protective gear to minimize any possible injury.
- Press and hold the On/Off button (15) for 3 seconds to power on the meter. Then use NFC to power on the meter and check the battery power. If the battery is low, charge the scooter.
- Stand on the foot deck with one foot and push off with another foot to start gliding. If you bought a seat version, sit on the seat first. Speed up slowly.
- Put your other foot on the foot deck to keep both feet stable. Press the throttle to speed up when you are balanced.
- Slow down by releasing the throttle. Squeeze the brake and stamp the rear fender with your foot at the same time for a brake.
- To turn, shift your body and turn the handlebar slightly.
WARNING: When braking rapidly, you risk serious injury due to loss of traction and falls. Maintain a moderate speed and look out for potential hazards.
Riding Notice
- DO NOT ride the scooter in the rain.
- Keep your speed between 3.1-6.2 mph (5-10 km/h) when you ride through speed bumps, elevator door sills, bumpy roads, or other uneven surfaces. Slightly bend your knee to better adjust to mentioned surfaces.
- Watch your head when passing through doorways.
- Watch your speed when traveling downhill. Use both brakes together when traveling at high speed.
- DO NOT press the throttle when walking with the scooter.
- Avoid contacting obstacles with the tire/wheel.
Dangerous Actions (No Attempting!)
- DO NOT carry heavy objects on the handlebar.
- DO NOT ride the scooter with only one foot.
- DO NOT ride on public roads, motorways, or highways.
- DO NOT rotate the handlebar violently while driving at high speed.
- Do not ride through puddles or any other (water) obstacles. In such a case, lower your speed and bypass the obstacle.
- The Electric scooter is for one rider only. Do not ride with another person. Do not carry a child.
- DO NOT step on the folding pedal while riding.
- DO NOT touch the hub motor after riding because it can get hot.
- DO NOT take your hands off the handlebar while riding. Do not ride with one hand only.
- DO NOT ride up and down stairs or jump over obstacles.
Folding and Carrying
- Make sure that the scooter is turned off. To fold, unlock the folding mechanism. Then fold the handlebar down.
- Hold the handlebar stem with either one hand or both hands to carry.
Maintenance
Daily Care and Maintenance
Cleaning and Storage:
- If you see stains on the scooter's body, wipe them off with a damp cloth. If stains won't scrub off, use toothpaste and a toothbrush, then wipe off with a damp cloth.
- Do not clean the scooter with alcohol, gasoline, kerosene, or other corrosive and volatile chemical solvents to prevent damage.
- Do not wash the board with a high-pressure water spray.
- During cleaning, ensure the scooter is turned off, the charging cable is unplugged, and the rubber flap is closed as water leakage may result in electric shock or other major problems.
- When not in use, keep it indoors where it is dry and cool. Do not put it outdoors for a long time. Excessive sunlight, overheating, and overcooling accelerate the battery pack's lifespan.
Battery Maintenance:
- Use original battery packs; use of other models or brands may bring about safety issues.
- Do not touch the contacts. Do not dismantle or puncture the casing. Keep contacts away from metal objects to prevent short circuits which may result in battery damage or even injuries and deaths.
- Use the original power adapter to avoid potential damage or fire.
- Mishandling of used batteries may do tremendous harm to the environment. To protect the natural environment, please follow local regulations to properly dispose of used batteries.
- After every use, fully charge the battery to prolong its lifespan.
Storage and Disposal:
- Store the scooter in a cool and dry place between 14°C and 104°C. In extremely humid environments, condensation or water accumulation may damage the battery rapidly.
- Devices are not intended for use at elevations greater than 2000 m above sea level.
- Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials. Store indoors when not in use.
- In daily use, try to avoid recharging the scooter after completely exhausting the battery. If the battery is low, charge it as soon as possible.
- Charge the scooter every other month to preserve the battery.
Regular Inspection & Maintenance
C: Check, A: Adjust, R: Replace, L: Lubricate, T: Tighten
| Inspection Items | 60 days | 180 days | 360 days |
|---|---|---|---|
| Whether the handlebar rotates or whether the steering parts are loose or worn | A/T | C/T | C/L |
| Whether the tire is properly inflated or the tire is worn | C | C | R |
| Front and rear axle gears, and wheel axles are deformed or worn | T | C/T | C/L |
| Whether the brake pad is worn | R | R | |
| Whether the rim is deformed or deflection | C | C | |
| Whether the frame and front fork are deformed or bruised | C | C | |
| Is the braking works good? | C | C | C |
| Whether the horn and headlights are working properly | C | C | |
| Whether the charger or charging plug is damaged | C | C | |
| Whether the tightening screws are loose | A | A | A |
Troubleshooting
The display interface can show error codes if a fault occurs. To view the fault status, press the on/off key to adjust the display interface to the 'E' interface when the symbol is flashing. The corresponding number under the interface represents the fault content.
| Error Code | Description |
|---|---|
| E-001 | Motor Hall fault |
| E-002 | Twist handle fault |
| E-003 | Controller fault |
| E-004 | Brake fault |
| E-005 | Voltage fault |
| E-006 | The instrument cannot receive the controller signal |
| E-007 | The controller cannot receive the instrument signal |
Specifications
Figure 4: Product Sizes (Unfolded and Folded Dimensions).
| Product | APEFOX T90 |
|---|---|
| Dimensions (Unfolded) | 1410*630*1360mm |
| Dimensions (Folded) | 1460*630mm (width), 1480*680mm (height) |
| Net Weight | 54.2kg |
| Max Load | 150kg |
| Recommended Age | 16-50 |
| Max Speed | <25km/h |
| Max Range | 90-100km |
| Operating Temperature | -10-40°C |
| IP Rating | IPX5 (Water-resistant for light rain use. Not recommended for heavy rain or prolonged exposure.) |
| Voltage | 60V DC |
| Max. Charging Voltage | 67.2V DC |
| Battery Capacity | 31.2Ah |
| Motor Peak Power | 3000W*2 (Dual Motors) |
| Charger Input Voltage | 110V-240V |
| Charger Output Voltage | 67.2V DC |
| Charger Output Current | 5A |
| Charging Time | 7-8 hours |
| Tire Type | 13-Inch Off-Road Tires |
| Climb Angle | ≤35° |
| Brakes | Hydraulic Disc Brakes |
| Body (Fold) | YES |
Notes on Specifications:
(1) The height of the body: distance from the ground to the highest end of the body.
(2) Description of the battery life: it is measured under the condition of full charge, a load of 165 lbs (75 kg), 77°F (25°C), on a flat road without wind, and at 25km/h of max speed. The real battery life will differ with different factors of load, humidity, wind speed, and operation habits.
(3) The maximum allowable weight shall be kept within 150kg (driver and objects included) in any case. Considering the extra weight of clothes or other accessories and the gravity generated by speed, the scooter will not support it if this load limit is exceeded.
Warranty & Support
Limited Warranty Statement
We warrant to the original purchaser that your product shall be free from defects in materials and workmanship under normal use for the period aforementioned. We do not warrant the operation of the product will be uninterrupted or error-free. We are not responsible for damage arising from failure to follow instructions relating to the product's usage.
After-Sales Service
| Part Name | Service Term | Warranty | Approach |
|---|---|---|---|
| Motor | 12 months | Failure in normal use | 1 year warranty for non-human damage |
| Battery | 12 months | Failure in normal use | Normal attenuation is not covered by warranty |
| Instrument accelerator | 12 months | Quality issues | 1 year warranty for non-human damage |
| Controller | 12 months | Quality issues | 1 year warranty for non-human damage |
| Charger | 12 months | Quality issues | Non-human damage can be guaranteed |
| Trumpet | 12 months | No sound | Non-human damage can be guaranteed |
| Frame | 24 months | Desoldering, nonartificial fracture | Non-human damage can be guaranteed |
| Tire | 1 months | Air leakage (non-artificial or pierced) | Non-human damage can be guaranteed |
Note: trade-in for the new one (within the warranty period)
Contact Information
Contact us if you experience issues relating to riding, maintenance, and safety, or errors/faults with your Electric scooter.
- Email: contact@apefox.com
- Website: www.apefox.com
User Tips
- Understand Speed Modes: The scooter has ECO, SPORT, and COMFORT modes. Familiarize yourself with each mode's characteristics to match your riding environment and local speed regulations. The maximum speed is less than 25 km/h.
- Regular Tire Checks: Given the 13-inch off-road tires, regularly check tire pressure and for any wear or damage, especially after riding on rough terrain, to ensure optimal performance and safety.
- NFC Unlock Convenience: Utilize the NFC unlock feature for quick and secure access. Keep your three NFC keys in safe, separate locations.