PowMr POW-300AH-12.8V-N

Contents

PowMr 12.8V 300Ah LiFePO4 Battery User Manual

Model: POW-300AH-12.8V-N

1. Introduction

The PowMr 12.8V 300Ah LiFePO4 Battery is a high-capacity, low-voltage energy storage solution designed for various applications including solar systems, RVs, marine vessels, and off-grid energy storage. Utilizing A-grade Lithium Iron Phosphate (LiFePO4) cells, this battery offers an ultra-long cycle life, high energy density, and stable performance. It features a built-in Battery Management System (BMS) for comprehensive protection and is an ideal upgrade replacement for traditional lead-acid batteries.

PowMr 12.8V 300Ah LiFePO4 Battery with key features

Image 1: PowMr 12.8V 300Ah LiFePO4 Battery highlighting its features.

2. Safety Information

⚠️ WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.

  • Do not short-circuit the battery terminals.
  • Do not expose the battery to fire or extreme heat.
  • Do not immerse the battery in water.
  • Do not disassemble or modify the battery.
  • Use only compatible chargers and charging methods.
  • Keep out of reach of children.

3. Setup and Installation

3.1 Unpacking and Inspection

Upon receiving your PowMr LiFePO4 battery, carefully unpack it and inspect for any signs of damage. Ensure all components are present.

Multiple views of the PowMr 12.8V 300Ah LiFePO4 battery

Image 2: Various angles of the PowMr 12.8V 300Ah LiFePO4 Battery.

3.2 Physical Dimensions and Terminals

The battery dimensions are approximately 522mm (L) x 240mm (W) x 218mm (H). It is equipped with M8 terminal bolts (14mm length, 8mm diameter) for secure connections.

Dimensions of the 300Ah-12.8V LiFePO4 battery and M8 terminal bolts

Image 3: Battery dimensions and M8 terminal bolt specifications.

3.3 Connection (Series and Parallel)

The PowMr LiFePO4 battery supports flexible configurations up to 4 units in series (4S) and 4 units in parallel (4P). This allows for a maximum total capacity of 1200Ah, a total voltage of 51.2V, and total energy of 61.44kWh.

When connecting batteries in series or parallel, ensure all batteries are of the same model, capacity, and state of charge. Use appropriate gauge cables and ensure all connections are tight and secure to prevent resistance and overheating.

Diagram illustrating series and parallel connections for expanding energy storage capacity

Image 4: Example wiring diagram for expanding energy storage capacity using series and parallel connections.

4. Operating Instructions

4.1 Charging

  • Recommended Charging Voltage: 14.6V ± 0.2V
  • Max Continuous Charge Current: 200A
  • Charging Temperature Range: 0°C to 45°C
  • The battery features an auto cut-off mechanism to prevent overcharging and protect battery life. Charging will stop if the temperature falls below 0°C or rises above 45°C.
Diagram showing increased charging efficiency with 200A current

Image 5: Charging efficiency comparison, showing faster charging with 200A current.

4.2 Discharging

  • Nominal Voltage: 12.8V
  • Low Voltage Protection Cut-off: 10.8V
  • Max Continuous Discharge Current: 200A
  • Discharge Temperature Range: -20°C to 60°C

4.3 Battery Management System (BMS)

The integrated 200A BMS provides comprehensive protection for the battery, ensuring safe and reliable operation. This includes protection against:

  • Overvoltage
  • Undervoltage (Over-discharge)
  • Overcurrent
  • Short Circuit
  • Overtemperature
Diagram detailing BMS protections: overvoltage, undervoltage, overcurrent, short circuit, overtemperature

Image 6: BMS protection features.

5. Maintenance

The PowMr LiFePO4 battery is designed to be maintenance-free. However, following these guidelines will help ensure optimal performance and longevity:

  • Regular Inspection: Periodically check battery terminals for corrosion or loose connections. Clean as necessary.
  • Storage: If storing the battery for an extended period, ensure it is charged to approximately 50% State of Charge (SOC). Store in a cool, dry place within the recommended storage temperature range of -10°C to 30°C.
  • Self-discharge Rate: The monthly self-discharge rate is less than 3%, minimizing capacity loss during storage.
  • Avoid Extreme Temperatures: Operating or storing the battery outside its specified temperature ranges can reduce its lifespan and performance.

6. Troubleshooting

The built-in BMS is designed to protect the battery from various fault conditions. If the battery stops functioning, check the following:

  • No Output Power:
    • Check if the battery voltage is below the low voltage protection cut-off (10.8V). If so, recharge the battery.
    • Verify that the load current does not exceed the maximum continuous discharge current (200A). The BMS may have triggered overcurrent protection.
    • Inspect for any short circuits in the wiring. The BMS will activate short circuit protection.
  • No Charging:
    • Ensure the charging voltage is within the recommended range (14.6V ± 0.2V).
    • Check if the charging current exceeds the maximum continuous charge current (200A).
    • Verify that the ambient temperature is within the charging temperature range (0°C to 45°C). The BMS will prevent charging outside this range.
    • Confirm that the charger is functioning correctly and properly connected.
  • Unusual Heat:
    • If the battery feels excessively hot, the BMS may have triggered overtemperature protection. Disconnect the load/charger and allow the battery to cool down in a well-ventilated area.
    • Ensure proper ventilation around the battery during operation.

If issues persist after checking these points, contact customer support for further assistance.

7. Specifications

Detailed technical specifications for the PowMr 12.8V 300Ah LiFePO4 Battery (Model: POW-300AH-12.8V-N):

Category Parameter Value
Basic Battery Specs Battery Chemistry LiFePO4 Lithium Iron Phosphate
Nominal Voltage 12.8V
Nominal Capacity 300Ah
Total Energy 3840Wh
Dimensions (L×W×H) 522×240×218mm
Net Weight ≤30kg (27.1kg)
Housing Material Flame-retardant ABS Plastic
Charge & Discharge Performance Built-in BMS Yes
Max Continuous Charge /Discharge Current 200A
Charging Voltage Range 10.8V ~ 14.6V
Recommended Charging Voltage 14.6V ± 0.2V
Low Voltage Protection Cut-off 10.8V
Round-trip Charge /Discharge Efficiency ≥99.5%
Monthly Self-discharge Rate <3%
Cycle Life & Temperature Resistance Standard Cycle Life Over 6000 Cycles (0.2C, 25℃, 80% DOD)
Discharge Temperature Range -20℃ ~ 60℃
Charging Temperature Range 0℃ ~ 45℃
Storage Temperature Range -10℃ ~ 30℃
Safety Protection BMS Multi-protection System Overcharge, Overdischarge, Overcurrent, Short Circuit, Overheat Protection
Expandability Max Series Connection 4 Units (Up to 51.2V)
Max Parallel Connection 4 Units (Up to 1200Ah)
Application Compatible Devices Solar Energy Storage, RV, Boat, Camper, Off-Grid System, UPS, Industrial & Medical Equipment, Electric Vehicles, Golf Carts, Floor Machines, Others
Detailed specification table for PowMr 12.8V 300Ah LiFePO4 Battery

Image 7: Comprehensive technical specifications.

8. Warranty and Support

The PowMr 12.8V 300Ah LiFePO4 Battery comes with a 5-year warranty, reflecting our commitment to quality and durability. PowMr also provides full technical support to assist with any questions or issues you may encounter.

For technical assistance or warranty claims, please refer to the contact information provided with your purchase or visit the official PowMr website.

PowMr company overview and mission statement

Image 8: PowMr company overview, highlighting commitment to quality and support.

9. User Tips

  • Initial Charge: It is recommended to fully charge the battery before its first use to ensure optimal performance and calibration of the BMS.
  • Ventilation: Although LiFePO4 batteries are safer than other lithium chemistries, always ensure adequate ventilation around the battery, especially during charging and heavy discharge, to dissipate any heat.
  • Cable Sizing: Use appropriately sized cables for your application to minimize voltage drop and prevent overheating, especially when drawing high currents.
  • Monitoring: Consider using a battery monitor to keep track of voltage, current, and state of charge, which can help in understanding battery performance and preventing over-discharge in systems without direct BMS communication.
  • Temperature Management: While the battery has a wide operating temperature range, prolonged operation at the extremes can impact lifespan. Aim for operation within moderate temperatures whenever possible.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.