1. Introduction
Thank you for choosing the DOOGEE Wild Boom Portable Wireless Speaker. This manual provides essential information for setting up, operating, and maintaining your speaker to ensure optimal performance and longevity. Please read it carefully before use.
2. What's in the Box
Verify that all items are present in your package:
- DOOGEE Wild Boom Wireless Speaker
- USB-C Charging Cable
- 3.5mm Audio Cable
- Lanyard Clip (for strap attachment)
- Quick Start Guide
- Detachable Handle
- Detachable Shoulder Strap
- Warranty Card

3. Product Overview (At a Glance)
Familiarize yourself with the speaker's buttons and ports:

| No. | Feature | Description |
|---|---|---|
| 1 | TWS Button | Initiates True Wireless Stereo pairing. |
| 2 | Power Button | Powers the speaker on/off, switches lighting effects. |
| 3 | Mode Switch Button | Switches between Bluetooth, TF Card, USB Drive, and AUX modes. |
| 4 | MFB Button | Multi-Function Button (Play/Pause, Answer/End Call, Voice Assistant). |
| 5 | Volume- | Decreases volume, previous track. |
| 6 | Volume+ | Increases volume, next track. |
| 7 | Type-C Charging Port | Connect for charging the speaker. |
| 8 | TF Card Slot | Insert TF (MicroSD) card for music playback. |
| 9 | USB Port | Insert USB drive for music playback or use as a power bank. |
| 10 | AUX Port | Connect external audio devices via 3.5mm cable. |
4. Setup
4.1. Charging the Speaker
Before first use, fully charge the speaker. Connect the USB-C charging cable to the speaker's Type-C port and a power source.
- Being Charged: The LED indicator turns solid red.
- Fully Charged: The LED indicator turns off.
- Low Battery Reminder: When the battery level is lower than 20%, the speaker will emit a voice prompt.

4.2. Power On/Off
- Power On: Press and hold the Power Button for 2 seconds. The blue light will turn on.
- Power Off: Press and hold the Power Button for 2 seconds. The light will turn off.
Note: If no device is connected to the speaker within 10 minutes of being powered on, the speaker will automatically power off.
4.3. Bluetooth Pairing
- Press and hold the speaker's Power Button for 2 seconds to turn it on.
- Turn on Bluetooth on your mobile device (phone or computer) and search for available devices.
- Select "Doogee Wild Boom" from the list to connect.
- Rapidly Flashing Blue Light: Bluetooth is in pairing mode.
- Blue Light Constantly On: Bluetooth is connected.
To Disconnect Bluetooth:
- Method 1: Turn off Bluetooth on your cell phone or computer.
- Method 2: Long press the "Mode Switch Button" for 3 seconds. The speaker will automatically disconnect from the connected Bluetooth device.
Note: Bluetooth cannot be disconnected during call mode.
4.4. TWS (True Wireless Stereo) Mode
TWS mode allows you to pair two DOOGEE Wild Boom speakers for a stereo sound experience.
- Ensure Speaker 1 is connected to your mobile phone and Speaker 2 is powered on and in pairing mode.
- Double-press the "TWS Button" on both Speaker 1 and Speaker 2. TWS pairing will be successful.
Note: If both speakers are turned on simultaneously again, they cannot perform TWS pairing automatically. You may need to re-initiate the pairing process.
4.5. Dual Device Connection
Connect the speaker to two Bluetooth devices simultaneously.
- On the first device, open the Bluetooth pairing list, connect the speaker, and complete pairing.
- Press and hold the "Mode Switch Button" on the speaker for 3 seconds to disconnect the Bluetooth connection from the first device and enter pairing mode for the second device.
- On the second device, open the Bluetooth pairing list, connect the speaker, and complete pairing.
- On the first device, reopen its Bluetooth pairing list, manually click to reconnect the speaker, and complete pairing.
4.6. Accessory Installation
Your speaker comes with a detachable handle and shoulder strap for easy portability.
Handle Installation:
- Insert the handle through the holes in the upper left and upper right corners of the speaker.
- Secure the handle. You can use the provided lanyard clips to help insert the handle through the holes.
Shoulder Strap Installation:
- Thread the shoulder strap through the holes at the top left and top right corners of the speaker.
- Secure the strap. Use the lanyard clips to assist in threading and adjust the length as needed.

5. Operating Instructions
5.1. Mode Switching (USB Drive / TF Card / AUX)
Click the "Mode Switch Button" to cycle between Bluetooth, TF Card, USB Drive, and AUX modes.
- USB Mode: Insert a USB drive into the USB port.
- AUX Mode: Insert a 3.5mm AUX cable into the AUX port.
- TF Card Mode: Insert a TF (MicroSD) card into the TF Card slot.
Note: In USB Drive/TF Card mode, the speaker supports MP3, WAV, WMA, APE, and FLAC audio formats.
Mode Memory: Upon startup, the device defaults to Bluetooth mode. However, if a USB drive, TF card, or AUX cable was inserted during the previous session, the speaker will power on and resume the mode that was active.
5.2. EQ Mode
The speaker features different Equalizer (EQ) modes to optimize sound for various environments.
- Indoor Mode: Click the MFB button once. Sound quality leans towards mid-low frequencies. Light off.
- Outdoor Mode: Click the MFB button once. Sound quality leans towards mid-high frequencies. White light on.
Memory function: The device remembers the last EQ mode used after being powered off.
5.3. RGB Lighting Modes
The speaker features a beat-synced colorful light show. With the product powered on, click the Power Button to switch between lighting effects:
- Running Horse
- Rhythm
- Breathing
- Fast Flash
- Gradient
- Solid Blue

5.4. Button Operation Summary
Refer to the table below for a quick guide to button functions:
| Function | Action |
|---|---|
| Power On/Off | Press and hold for 2 seconds |
| Toggle Lighting Effects (Power On) | Single Click (Power Button) |
| Manually Force Unpair (Power Off) | Press and hold for 5 seconds (Mode Switch Button) |
| Play / Pause | Single click (MFB Button) |
| Answer the phone | Single click (MFB Button) |
| Hang up the phone | Single click (MFB Button) |
| Cancel dialing | Single click (MFB Button) |
| Voice Assistant | Press and hold for 2 seconds (MFB Button) |
| Reject calls | Press and hold for 2 seconds (MFB Button) |
| Voice forwarding | Press and hold for 2 seconds (MFB Button) |
| Volume Up | Single Click (Volume+ Button) |
| Next Track | Press and hold for 2 seconds (Volume+ Button) |
| Volume Down | Single Click (Volume- Button) |
| Previous Track | Press and hold for 2 seconds (Volume- Button) |
| Audio mode switch | Single click (Mode Switch Button) |
| Disconnect Bluetooth | Press and hold for 3 seconds (Mode Switch Button) |
| Toggle EQ Mode | Single Click (MFB Button) |
| On/Off TWS Mode | Double Click (TWS Button) |
6. Maintenance
6.1. Routine Maintenance
- To extend battery life, fully charge the battery at least every three months.
- Battery life will vary depending on usage and environmental conditions.
- Do not expose the Doogee Wild Boom to liquids while the cable is plugged in.
- Do not expose the Doogee Wild Boom to water while charging, as this may cause permanent damage to the speaker or power supply.
- If liquid spills onto the speaker, do not charge it until the speaker is completely dry and clean. Charging while wet may damage the speaker.
6.2. Care and Maintenance
- Do not place the device near naked flame sources such as a lighted candle.
- Use the product in temperate climates only.
- Always unplug the device before cleaning it.
- Clean the speaker with a soft dry cloth only. Never use solvents.
- The battery (batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.
7. Troubleshooting
7.1. Force Shutdown/Reset
If the device freezes or becomes unresponsive, simultaneously long-press the Power Button and the Mode Switch Button for 2 seconds to force a shutdown and reset.
7.2. Restore Factory Settings
While powered on, long-press the "Mode Switch Button" for 5 seconds to restore the speaker to its factory default settings.
7.3. Common Issues
- No Power: Ensure the speaker is charged. Connect to a power source and check the charging indicator.
- Cannot Pair Bluetooth: Make sure the speaker is in pairing mode (rapidly flashing blue light). Ensure your device's Bluetooth is on and within range. Try disconnecting other Bluetooth devices.
- No Sound: Check the volume levels on both the speaker and your connected device. Ensure the correct input mode (Bluetooth, AUX, USB, TF Card) is selected.
- Distorted Sound: Reduce the volume on both the speaker and your device. Ensure the speaker is not too far from the connected device in Bluetooth mode.
8. Specifications
| Feature | Specification |
|---|---|
| Bluetooth Version | V5.3 |
| Speaker Configuration | 48mm*2 tweeters + 105*75mm woofer |
| Frequency Response | 50Hz-20kHz |
| Rated Audio Output Power | 80W |
| Peak Audio Output Power | 100W |
| Audio Source | Bluetooth, TF card, USB flash drive, AUX |
| Music Playback Time | Approximately 20 hours (at 30% volume, lights off; varies depending on volume and audio content) |
| Battery Capacity | 11.1V/2000mAh |
| Power Input | 5V-3A (USB-C) |
| Battery Charging Time | 3.5 hours |
| Waterproof Rating | IP55 (Waterproof & Dustproof) |
| Dimensions (W x D x H) | 304.3*113.5*133.6mm |
| Weight | 1.956kg |
| Voltage Range | USB (5-20V DC) |
| Sound Mode | Extra Bass Mode |
| Built-in Microphone | Yes |
| Bluetooth Range | 12M |
| Overvoltage Protection | OVP-26V |



9. User Tips
- For the best audio experience, experiment with both Indoor and Outdoor EQ modes to match your environment.
- Utilize the TWS pairing feature with a second Wild Boom speaker for an immersive stereo sound, especially for parties or larger gatherings.
- The built-in emergency power bank is useful for charging small devices on the go, but remember it will reduce the speaker's playtime.
- Keep the speaker's firmware updated if new versions become available, as this can improve performance and add features.
10. Safety and Compliance
10.1. FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
10.2. EC Declaration
This product complies with the below listed UK Directives:
- Radio Equipment Regulations 2017
- The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
- The Batteries and Accumulators (Placing on the Market) Regulations 2008 (as amended)
- The Waste Batteries and Accumulators Regulations 2009 (as amended)
Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
11. Further Information and Support
For more detailed information, troubleshooting, or support, please refer to the full user manual available in PDF format. You can access the PDF manual here.
Alternatively, scan the QR code on the Quick Start Guide included in your package for more function information.