Aninerel 2500W 12V Hybrid Solar Inverter with 12V 100Ah LiFePO4 Battery Set

Contents

Aninerel 2500W 12V Hybrid Solar Inverter and LiFePO4 Battery Set User Manual

Model: ANL-2000W-12L-W (Inverter) / ANL-12.8V-100AH (Battery)

1. Introduction

This manual provides essential information for the safe and efficient operation of your Aninerel 2500W 12V Hybrid Solar Inverter and 12V 100Ah LiFePO4 Battery Set. Please read this manual thoroughly before installation and use, and keep it for future reference.

2. Safety Information

  • Ensure all electrical connections are made by qualified personnel.
  • Do not attempt to open or repair the inverter or battery unless specifically instructed in this manual.
  • Keep the inverter and battery away from flammable materials, moisture, and direct sunlight.
  • Ensure proper ventilation around the inverter to prevent overheating.
  • Wear appropriate personal protective equipment (PPE) during installation and maintenance.
  • Disconnect all power sources before performing any maintenance or wiring.

3. Product Features

3.1. Inverter Features (Model: ANL-2000W-12L-W)

  • Pure Sine Wave output.
  • Power factor 1.0.
  • Built-in MPPT 120A solar charge controller.
  • Capable of feeding into the grid.
  • Can operate without a battery.
  • Optional WiFi remote monitoring.
  • PV input Voltage range: 50Vdc-500Vdc.
  • Compatible with LiFePO4 batteries via RS485 communication.
  • Detachable dust cover for harsh environments.
  • Lithium battery activation function by PV or Utility.
  • Supports multiple output priorities: UTL (Utility), SOL (Solar), SBU (Solar-Battery-Utility), SUB (Solar-Utility-Battery), SUF (Solar-Utility-Feed).
  • EQ function to optimize battery performance and extend lifecycle.

3.2. LiFePO4 Battery Features (Model: ANL-12.8V-100AH)

  • High cycle life: >6000 cycles.
  • Energy capacity: 1280WH.
  • Built-in Battery Management System (BMS) for comprehensive protection.
  • Maintenance-free operation.
  • Lightweight: Approximately 11-13 kg (significantly lighter than lead-acid batteries of similar capacity).
  • Environmentally friendly: No pollution.
  • IP65 level water resistance.
  • 80% efficient capacity usage.
  • BMS ensures 100% charging safety.
  • BMS provides overcharge, overdischarge, overcurrent, and short circuit protection, along with cell voltage self-balance.
  • Voltage holds at around 12.8V (provides >80% capacity).
  • 100% Depth of Discharge (DOD).

4. Setup

4.1. Unpacking and Inspection

Carefully unpack the inverter and battery. Inspect for any physical damage. Ensure all components listed in the packing list are present.

4.2. Mounting the Inverter

Mount the inverter in a well-ventilated area, away from direct sunlight and heat sources. Ensure sufficient clearance around the unit for airflow.

4.3. Wiring Connections

Refer to the application diagram and product overview for detailed wiring instructions. All wiring should be performed by a qualified electrician.

Application Diagram
Figure 1: Application Diagram showing connections between solar panel, utility grid, generator, inverter, battery, and home loads.
Inverter Product Overview
Figure 2: Product Overview of the Inverter, detailing LCD display, indicators, buttons, power switch, RS232/RS485 ports, AC input/output, PV input, and battery terminals.
Video 1: Demonstrates the physical connections and initial power-up sequence of the inverter, including battery terminal connections.

4.3.1. Battery Connection

Connect the 12V 100Ah LiFePO4 battery to the inverter's battery terminals (POS+ and NEG-). Ensure correct polarity. The battery features an internal BMS for safety.

  • Parallel Connection: Up to 4 batteries can be connected in parallel to increase capacity.
  • Series Connection: Up to 2 batteries can be connected in series to increase voltage (e.g., for a 24V system, though this inverter is 12V, ensure compatibility if using multiple inverters).
LiFePO4 Battery Connection Diagrams
Figure 3: LiFePO4 Internal Components diagram (BMS, Cells) and connection diagrams for Parallel (maximum 4 batteries) and Series (maximum 2 batteries).

4.3.2. PV Connection

When selecting proper PV modules, consider the following parameters:

  • Max. PV Array Power: 3000W
  • Max. PV Array Open Circuit Voltage (Voc): 500VDC (Voc of PV modules should not exceed this).
  • Max. Solar Charge Current: 120A

4.3.3. AC Input/Output Connection

Connect the utility grid to the AC input terminals and your home loads to the AC output terminals. The inverter supports dual outputs for smart load management.

5. Operating Instructions

5.1. Powering On/Off

After all connections are secure, switch on the power/off switch on the inverter. The LCD display will illuminate, showing system status.

5.2. LCD Display and Function Buttons

The inverter features an LCD display for monitoring system status and function buttons for navigation and settings adjustment. Refer to Figure 2 for button layout.

5.3. Output and Input Priority Modes

The inverter supports various charger power priority and output power priority modes to suit your energy management needs. These can be configured via the inverter's interface.

Output and Input Mode Diagrams
Figure 4: Diagrams illustrating Charger Power Priority (Solar and Utility, Solar Priority, Solar Only) and Output Power Priority (Utility first, SUB priority, Solar first, SBU priority, SUF priority).

5.4. WiFi Remote Monitoring

For remote monitoring of the inverter's operating status, an external Wi-Fi module is available. Download the "Smart Ess" app from the App Store or Google Play.

Smart App Management
Figure 5: Smart App Management for the inverter, showing Wi-Fi module and app download options.

6. Maintenance

6.1. Inverter Maintenance

  • Regularly check for loose connections and ensure all terminals are tightened.
  • Clean the detachable dust cover periodically, especially in harsh environments, to maintain optimal airflow and prevent dust buildup.
  • Keep the inverter's ventilation openings clear of obstructions.

6.2. Battery Maintenance

The LiFePO4 battery is designed to be maintenance-free. However, it is recommended to:

  • Periodically inspect the battery terminals for corrosion and ensure they are clean and tight.
  • Keep the battery in a cool, dry place, away from direct heat or extreme cold.

7. Troubleshooting

If you encounter any issues with your Aninerel Inverter and Battery Set, please refer to the following general troubleshooting steps:

  • No Power: Check all connections, ensure the battery is charged, and verify the main power switch is ON.
  • Inverter Fault Indicator: If the fault indicator is lit, consult the full user manual (PDF) for specific error codes and their meanings.
  • Unusual Noise: While cooling fans may run continuously, excessive or unusual rattling sounds should be investigated. Ensure the inverter is securely mounted and free from vibrations.
  • Charging Issues: Verify PV input voltage and current, check AC input if charging from the grid, and ensure battery communication (RS485) is functioning correctly.

For complex issues or persistent problems, please contact Aninerel customer support.

8. Specifications

8.1. Inverter Technical Data (Model: ANL-2000W-12L-W)

Category Parameter Value
ModelModel NumberANL-2000W-12L-W
Capacity2KVA
Battery FeaturesParallel CapabilityNO
Lithium Battery ActivationYES (By PV only)
Lithium Battery CommunicationYES (RS485)
InputNominal Voltage230VAC
Acceptable Voltage Range170-280VAC (PC); 90-280VAC (Home Appliances)
Frequency50/60 Hz (Auto sensing)
OutputNominal Voltage220/230VAC±5%
Surge Power3000VA
Frequency50/60Hz
WaveformPure Sine wave
Transfer Time10ms (PC); 20ms (Home Appliances)
Peak Efficiency (PV to INV)96%
ProtectionPeak Efficiency (Battery to INV)93%
Overload Protection5s@>=140% load; 10s@100%~140% load
Crest Factor3:1
Admissible Power Factor0.6~1 (inductive or capacitive)
Battery ChargerBattery Voltage12V
Floating Charge Voltage13.5V
Overcharge Protection14.1V
Charging MethodCC/CV
Solar & AC ChargerSolar Charger TypeMPPT
Max. PV Array Power900W
Max. PV Array Open Circuit Voltage160VDC
PV Array MPPT Voltage Range30VDC~160VDC
Max. Solar Input Current30A
Max. Solar Charge Current60A
AC ChargerMax. AC Charge Current80A
Max. Charge Current (PV+AC)120A
Physical Dimensions (D x W x H)358x295x105.5 mm
PhysicalNet Weight5.80 Kg
Communication InterfaceRS232/RS485
EnvironmentOperating Temperature Range-10°C to 50°C
Storage Temperature-15°C ~ 50°C
Humidity5% to 95% Relative Humidity (Non-condensing)

*Product specifications are subject to change without further notice.

8.2. LiFePO4 Battery Technical Data (Model: ANL-12.8V-100AH)

Parameter Value
Nominal voltage12.8V
Nominal capacity100Ah
Energy1280WH
Cell assembly3.2V100AH-4S1P
Dimension (mm)260*168*215
Weight (Kg)11±0.5Kg
Cycle Life>6000 (@0.5C 100%DOD)
Charging voltage14.4-14.6V
Discharge cut-off voltage10V±0.5V
Maximum discharge current100A
Maximum charging current50A
Discharge operating temperature-20°C~55°C
Charging operating temperature0°C~55°C
Storage temperature (within a month)-20°C~45°C
Storage temperature (within a year)0°C~35°C
Series connection4
Parallel connection4 (Need to control the battery at the same voltage)
Charger selection14.6V20-50A

9. User Tips

  • Fan Noise: Be aware that the inverter's cooling fans may run continuously, producing a noticeable sound. This is normal for cooling high-power electronics.
  • Battery Charging: The inverter is capable of charging the battery from both solar panels (PV) and the utility grid (mains power).
  • Battery Quantity: This product is typically sold as a set with one 12V 100Ah LiFePO4 battery, unless specified otherwise in your order options.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller directly. Keep your purchase receipt and product model numbers handy for faster assistance.

A detailed user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.