Estardyn 2.1-inch TFT LCD GC9B72

Contents

Estardyn 2.1-inch Round TFT Display Module User Manual

Model: 2.1-inch TFT LCD GC9B72

1. Product Overview

The Estardyn 2.1-inch Round TFT Display Module is a high-quality, full-color display designed for various embedded applications. Featuring a 360x360 resolution and a GC9B72 driver IC, it offers high color reproduction and a wide viewing angle, making it suitable for smart home devices, industrial control panels, wearable UIs, and DIY projects. This module utilizes a 4-Wire SPI interface for easy integration.

Estardyn 2.1-inch Round TFT Display Module features
Figure 1: Estardyn 2.1-inch Round TFT Display Module highlighting key features like 360x360 resolution, GC9B72 driver IC, 4-Wire SPI interface, full color display, and 350 cd/m² brightness.

2. Specifications

FeatureSpecification
Size2.10 inch
Resolution360x360
Driver ICGC9B72
Interface4-Wire SPI
ColorFull Color
Brightness350 cd/m²
Supply Voltage2.8-3.3V
Module Dimensions55.92 × 57.58 × 2.01 mm
Active Area (AA)52.92 × 52.92 mm
Operating Temperature-20°C to +70°C
ESD ProtectionAir +8KV / Contact +4KV
Power Consumption300mW
CertificationsISO9001 / RoHS / CE
Product Dimensions Diagram
Figure 2: Detailed product dimensions for the Estardyn 2.1-inch Round TFT Display Module.
Stable Performance Specifications
Figure 3: Overview of stable performance specifications including brightness, operating temperature, ESD protection, power consumption, and certifications.

3. Setup and Connection

This section details the physical connection and pin definitions required to integrate the Estardyn 2.1-inch Round TFT Display Module into your project.

3.1 Pin Definition

The module uses a 4-Wire SPI interface. Refer to the table and diagram below for pin assignments and functions.

PINSYMBOLFUNCTION
1GNDPower Ground
2RSTDisplay Reset Pin
3SDAData
4SCLClock
5CSChip Select Signal
6DCData/Command Selection Pin
7TEFrame Sync
8SDOData Output Pin
9VDDDigital Power Positive
10LED-ABacklight Anode
11LED-KBacklight Cathode
12GNDPower Ground
Pin Definition Diagram
Figure 4: Front and back views of the display module with pin definitions and power requirements.

3.2 Reference Circuit Diagram

For proper integration with a microcontroller (MCU), follow the reference circuit diagram below. Ensure correct voltage levels (2.8-3.3V) are supplied to VDD and backlight pins.

Reference Circuit Diagram
Figure 5: Reference circuit diagram showing connections between an MCU and the TFT LCD module via SPI interface.

3.3 Power Supply

The module requires a power supply of 2.8-3.3V. Ensure your power source can provide stable voltage within this range to prevent damage or erratic display behavior. The typical power consumption is 300mW.

4. Operating Instructions

Once correctly wired and powered, the display module is controlled via the 4-Wire SPI interface. You will need to implement the necessary software drivers for the GC9B72 IC on your microcontroller to send display data and commands.

  1. Initialization: After power-up, the display controller (GC9B72) needs to be initialized with a sequence of commands. This typically involves setting display mode, pixel format, and other parameters.
  2. Data Transfer: Image data is sent to the display's frame buffer via the SPI interface. The SDA pin carries the data, and SCL provides the clock signal. The CS pin selects the display, and DC differentiates between command and data bytes.
  3. Backlight Control: The backlight (LED-A, LED-K) can be controlled separately, often through a PWM signal from the microcontroller to adjust brightness.

Refer to the GC9B72 datasheet for detailed command sets and timing diagrams for software development.

5. Maintenance and Care

To ensure the longevity and optimal performance of your display module, follow these maintenance guidelines:

  • Handling: Always handle the module by its edges. Avoid touching the display surface or the flexible flat cable (FPC) connector.
  • ESD Protection: The module is sensitive to Electrostatic Discharge (ESD). Always use appropriate ESD precautions (e.g., ESD wrist strap, grounded workstation) when handling. The module is protected up to Air +8KV / Contact +4KV.
  • Cleaning: If necessary, gently clean the display surface with a soft, lint-free cloth. Do not use abrasive cleaners or solvents.
  • Operating Environment: Operate the module within the specified temperature range of -20°C to +70°C. Avoid exposure to extreme humidity or direct sunlight.
  • Storage: Store the module in its original packaging or an anti-static bag in a cool, dry place when not in use.

6. Troubleshooting

If you encounter issues with your display module, consider the following troubleshooting steps:

  • No Display/Blank Screen:
    • Verify that the power supply (VDD) is within the 2.8-3.3V range and stable.
    • Check all pin connections (GND, VDD, SPI lines, backlight) for proper contact and correct wiring according to the pin definition and circuit diagram.
    • Ensure the display controller (GC9B72) has been correctly initialized in your software.
    • Confirm the backlight is receiving power and is enabled.
  • Incorrect Colors/Distorted Image:
    • Check the SPI data lines (SDA, SCL) for signal integrity.
    • Verify that the data format and pixel order sent from your microcontroller match the display controller's requirements.
    • Ensure the DC (Data/Command) pin is correctly toggled for commands and data.
  • Flickering Display:
    • Check for stable power supply.
    • Ensure the SPI clock speed is within the recommended limits for the GC9B72.
    • Verify that the frame sync (TE) signal, if used, is correctly handled.
  • Module Not Responding:
    • Ensure the RST (Reset) pin is correctly pulsed during initialization.
    • Check the CS (Chip Select) pin to ensure the display is being selected for communication.

7. User Tips

  • Software Libraries: For easier integration, search for existing open-source libraries for the GC9B72 driver IC or general SPI TFT displays compatible with your chosen microcontroller platform (e.g., Arduino, ESP32, Raspberry Pi).
  • Datasheet Reference: Always keep the GC9B72 datasheet handy during development for detailed register settings and command sequences.
  • Prototyping: When prototyping, use a breadboard or a dedicated adapter board to ensure secure connections before finalizing your PCB design.
  • Power Management: Consider implementing power-saving modes in your software if the display is battery-powered, as the backlight can be a significant power consumer.
Wide Application Examples
Figure 6: Examples of wide applications for the display module, including Smart Home, Instrument Panel, Wearable UI, Industrial Control, and DIY Projects.

8. Warranty and Support

This Estardyn display module is manufactured under strict quality control standards. For technical support, driver examples, or further assistance, please contact your vendor or refer to the official Estardyn website. While specific warranty details may vary by region and reseller, general support for product functionality and integration is typically available.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.