Important Safety Information
Warning: This unit is for vehicles with 12V batteries only. Using it with other battery types may be dangerous. Read and understand all safety information before use to prevent damage, electric shock, explosions, fire, property damage, and personal injury.
- Always read the instruction manual carefully before using this unit.
- Do NOT use this unit if any cable clamp or cord is damaged.
- Do NOT use in place of a vehicle battery or as a battery charger.
- Never leave the unit connected to a car battery after successfully starting the car.
- Use only the jumper cable provided with this unit.
- Ensure the BLUE plug of the jumper cable is fully seated into the jumping socket to prevent melting.
- Ensure all battery connections are CLEAN and clamps are well connected before jump starting. Dirty or corroded terminals can reduce performance.
- Do NOT jump start more than 3 times in a row to prevent overheating. Allow two minutes between attempts.
- Do NOT connect the two clamps together.
- Ensure the electric charge is greater than or equal to 60% before starting the car.
- Do NOT use by young or infirm persons without supervision.
- Do NOT allow the product to become wet or immerse it in water.
- Do NOT operate in explosive atmospheres (flammable liquids, gases, dust).
- Do NOT modify or disassemble the Epower unit. Only a repair technician may repair it.
- Do NOT expose the product to extreme heat (above 70°C) or fire.
- Charge only at ambient temperatures between 0°C and 60°C.
- Do NOT use the unit to jump start a vehicle while charging its internal battery.
- If the unit is leaking liquid, dispose of it at a proper recycle facility immediately. If liquid contacts skin, wash with soap and water. If liquid contacts eyes, rinse with cold running water for at least 10 minutes and seek medical attention.
- Product contains lithium-based battery; dispose of it according to local regulations at the end of its life.
Do Not Submerge In Water
Do Not Disassemble
Do Not Drop
Avoid Extreme Temperatures
Do Not Place Near or Into Fire
The VTOMAN X5 Cross features comprehensive safety protections including overcharge/discharge, fuse protection, and against-reverse plug.
Safety is a top priority with protections against Over-Charge, Over-Current, High-temp, Spark-Proof, Short-Circuit, Reverse-Polarity, Over-Voltage, Over-Load, Low-temp, and Reverse-Charge.
Product Overview
The VTOMAN X5 Cross is a versatile 5-in-1 emergency tool designed for various outdoor and roadside situations. It combines a powerful jump starter, a portable tire inflator, a power bank, an LED flashlight, and an SOS emergency light.
The X5 Cross offers 6 key functions: Flashlight, Bike pump, Power your devices, Tire inflator, Ball pump, and Jump starter.
Product Parts and Functions
Diagram illustrating the various parts of the VTOMAN X5 Cross, including the Jump start socket, LCD Display, Power switch, Pressure increase/decrease buttons, Setting button, Light switch, Blower switch, USB-C Input Port, Aerated port, LED Flash Light, USB Output Port, Suction port, and Air blast port.
- Jump Start Socket: For connecting smart battery clamps.
- LCD Display: Shows battery level, tire pressure, and operating modes.
- Power Switch: Turns the device on/off and checks battery level.
- Pressure Increase/Decrease Buttons: Adjusts target pressure for inflation.
- Setting Button: Switches inflation target and pressure units (BAR, PSI, KPA).
- Light Switch: Controls the LED flashlight modes.
- Blower Switch: Activates the air blower function.
- USB-C 5V/2A Input Port: For charging the X5 Cross.
- USB 5V/2.1A Output Port: For charging external devices.
- Suction Port: For deflation using the blower hose.
- Air Blast Port: For inflation using the blower hose.
Setup
Initial Charging
Charge It First! Before initial use, or while reading this manual, connect your X5 Cross to a power source using the provided Type-C cable. A wall charger is NOT included.
- Plug the home adaptor (not included) into a universal socket.
- Connect the USB-C connector to the USB-C 5V/2A Input Port on the X5 Cross.
The battery icon on the LCD display will blink during charging, with bars advancing from bottom to top. When fully charged, the battery icon will show 4 solid bars.
The X5 Cross offers up to 18 months of standby time. To extend its life, charge the product every 3-6 months.
Connecting Nozzles for Inflation/Deflation
To connect the multi-function nozzle, push up to unlock, insert the nozzle, then press down to lock.
The X5 Cross can inflate various items including balls, bicycle tires, motorcycle tires, car tires, and SUV tires, with specific PSI ranges for each.
Operating Instructions
Checking Battery Power
Press the power button briefly to check the current battery level on the LCD display.
| Battery Icon | 0 Bar | 1 Bar | 2 Bars | 3 Bars | 4 Bars |
|---|---|---|---|---|---|
| Battery Power | 0% | 25% | 50% | 75% | 100% |
When the product's power is less than 10%, the corresponding power indicator will flash.
The display shows Battery Level, Tire Pressure Unit, Inflation Mode, Real-Time pressure, and Preset pressure.
LED Flashlight Operation
- Short-press the light switch to turn on the LED light (white light stays on).
- Press again to cycle through flash mode, SOS mode, and then turn the light off.
The 400 Lumens LED offers Lighting, SOS, and Strobe modes for emergencies.
Air Blower Operation
In standby or normal working mode, short-press the air blower key to turn on the blower; press again to turn it off.
Inflation and Deflation
The X5 Cross features a dual-purpose air pump with a maximum pressure of 150 PSI and an airflow speed of 150 L/min for both inflation and deflation.
Portable inflation anytime, anywhere with 150 L/min inflate and deflate speed.
How to Inflate:
- Connect the air hose to the tire valve.
- Press Button 4 to select mode (Ball/Bike/Car/SUV/Free).
- Press Button 2 (+) or Button 3 (-) to set desired pressure.
- Press Button 6 to start inflation.
- Auto stops at target pressure. Press Button 6 again to stop manually.
Tip: Long press Button 4 to switch units (PSI/BAR/KPA).
Step-by-step visual guide for inflation.
How to Deflate:
- Connect the blower tube to the deflatable item.
- Press and hold the power icon for 2 seconds to turn on the device.
- Tap the button to start deflation.
Step-by-step visual guide for deflation.
Jump Starting a 12V Vehicle
The X5 Cross delivers a peak current of 3500A, capable of starting 12V dead batteries, including those with zero voltage. It supports up to 9.0L gasoline or 8.0L diesel engines.
Jump start flat batteries with REAL 3500A, suitable for 12V vehicles, 9L Gas, 8L Diesel, and provides up to 50 starts.
The X5 Cross can start dead batteries in vehicles with up to 9L Gas and 8L Diesel engines.
- Connect the blue plug of the smart battery clamp fully into the jump start socket on the X5 Cross. Ensure the Cable Indicator is off.
- Connect the Red Clamp to the positive (+) battery terminal of the vehicle.
- Connect the Black Clamp to the negative (-) battery terminal of the vehicle.
- Observe the Cable Indicator and follow its instructions:
- GREEN LIGHT on: Connection is correct and circuit is working. You can turn on the engine to jump-start directly.
- REVERSE RED LIGHT on: Connection is wrong. Correct the clamps as per step 2. Wait until the GREEN LIGHT is on before attempting to start the engine.
- GREEN LIGHT blinking: Vehicle battery is low. Press the "BOOST" button. Wait until the GREEN LIGHT becomes solid, then turn on the engine within 30 seconds.
- No Lights on: Vehicle's battery may be damaged. After confirming correct clamp connection, press the "BOOST" button. Wait until the GREEN LIGHT is on, then turn on the engine within 30 seconds.
- Start the vehicle.
- Once the vehicle is started, remove the jumper cable from the vehicle battery. Leave the vehicle's engine running.
Visual guide for jump starting: Insert blue end, connect clips (red+, black-), start engine.
Power Bank Function
The 44.4Wh portable power bank can charge various USB devices.
Power all your needs with 44.4Wh True Capacity, charging phones, cameras, headphones, and smartwatches.
Features USB-C Input 5V/2A and USB-A Output 5V/2.1A for convenient device charging.
Maintenance
- To extend battery life, recharge the X5 Cross every 3-6 months, especially during long standby periods.
- Keep battery connections clean and free from corrosion to ensure optimal performance during jump starting.
- Store the unit in a cool, dry place, away from direct sunlight and extreme temperatures (operating temperature: -20°C to 60°C / -4°F to 140°F).
The X5 Cross is designed to operate reliably in temperatures from -4°F to 140°F.
Troubleshooting
| Finding | Cause | Remedies |
|---|---|---|
| No response when pressing the switch button. | Low voltage protection of EPower is started. | Plug the adaptor into the 5V 2A input port to activate. |
Specifications
Technical Specifications
| Feature | Value |
|---|---|
| Model No. | JS-605 |
| Battery Type | Lithium polymer |
| Capacity | 44.4Wh/12000mAh, 14.8V |
| Starting Current | 400A |
| Peak Current | 3500A |
| Maximum Inflation Pressure | 4-150PSI |
| Air Flow Speed | Inflate 150L/min, Deflate 150L/min |
| USB-C In | 5V=2A |
| USB-A Out | 5V=2.1A |
| Operating Temp | -20°C~60°C / -4°F~140°F |
| Full Charge Time | About 3 Hours |
| Conversion Rate | 85%~90% |
| Number Of Built-in Batteries | 4 |
| External Testing Certification | WEEE, MSDS, ROHS, FCC, CE, CCC |
Note: The capacity is 44.4Wh, which corresponds to 3000mAh per single battery cell. The X5 Cross has 4 battery cells, making the total capacity 12000mAh.
Package Content
The package includes all necessary accessories for immediate use.
| # | Part Name | Quantity |
|---|---|---|
| 1 | Host | 1 |
| 2 | Smart battery clamp | 1 |
| 3 | Air inflator hose | 1 |
| 4 | Air inflator nozzle | 5 |
| 5 | Blower hose | 1 |
| 6 | Blower nozzle | 5 |
| 7 | C-C 10W Cable | 1 |
| 8 | USB-C 10W Cable | 1 |
| 9 | Packaging Bag | 1 |
| 10 | Quick Reference Guide | 1 |
Warranty & Support
Warranty Includes:
- 18 Months Online After-Sales Service: Timely and effective online support for 18 months after purchase.
- 30 Days Money Back Guarantee: Return for any product issue within the first 30 days of purchase.
- 30 Days to 18 Months: Replacement of defective units due to manufacturing issues within 18 months.
Disclaimer:
- For repair or replacement, the original purchaser must provide the original receipt (order ID).
- Warranty does not cover damage from normal wear and tear, physical abuse, improper installation, misuse, modification, or unauthorized third-party repairs.
- VTOMAN is not responsible for accidental or indirect damage caused by incorrect use or misuse of this product.
- All warranty claims are limited to repair or replacement of the defective product at VTOMAN's sole discretion.
Contact Us:
- Email Support: Support@vtoman.com
- Phone Support (US): 1-888-818-9811 (Mon. - Fri. 9 am. - 5 pm. PST)
- Lifetime Technical Service
User Tips
- Switching Pressure Units: To convert between PSI, BAR, and KPA units for inflation, long press the Setting button. This is useful for matching different vehicle or item requirements.
- Optimal Charging: For best battery longevity, ensure the unit is charged every 3-6 months, even when not in active use.
- Quick Inflation: The 150PSI fast tire inflator can fill a standard car tire from 25PSI to 36PSI in just 30 seconds, making it efficient for roadside emergencies.
Product Video
Demonstration of the VTOMAN X5 Cross jump starting a car, charging devices, and using the LED light.