BAOFENG UV-36 PRO

Contents

BAOFENG UV-36 PRO 10W Tri-Power Walkie Talkie User Manual

Model: UV-36 PRO (FCC ID: SW-9)

1. Introduction and Safety Warnings

Thank you for purchasing the BAOFENG UV-36 PRO, a dual-band, dual-display, and dual-watch radio designed for secure, instant, and reliable communications. Please read this manual carefully to ensure optimal performance and safe operation.

1.1 General Safety Warnings

WARNING! European Users:

Operation of this unit in Transmit mode requires a valid Amateur Radio License from your respective Country's Amateur Radio Licensing Authority for the frequencies and transmitter power levels this radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU.

ATTENTION! Programming the Radio:

When programming, always read the factory software data first, then rewrite with your desired frequencies. Errors may occur otherwise. Use the programming cable with a PC to program authorized frequencies, bandwidth, power, etc. Programming must comply with your FCC (or EU/other country) license certification.

ATTENTION! RF Energy Exposure and Product Safety:

Before use, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

1.2 Precautions for Portable Terminals

Operating Prohibitions:

  • Do not operate in locations with fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not operate near blasting areas.
  • Do not operate near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate where wireless communication equipment is prohibited.

Important Tips:

  • Use only authorized accessories.
  • Keep the product at least 2.5 cm away from your body during transmission.
  • Avoid prolonged high-volume reception.
  • Do not place the product over or in an airbag deployment area in vehicles.
  • Keep the product and accessories out of reach of children and pets.
  • Operate within the specified temperature range.
  • Continuous transmission can lead to heat accumulation; allow for cooling.
  • Handle with care; do not disassemble, modify, or repair without authorization.

1.3 Precautions for Batteries

Charging Prohibitions:

  • Do not charge or replace the battery in locations with fuels, chemicals, or explosive materials.
  • Do not charge a wet battery; dry it thoroughly first.
  • Do not charge a deformed, leaking, or overheated battery.
  • Do not charge with an unauthorized charger.
  • Do not charge in areas with strong radiation.
  • Avoid overcharging, as it shortens battery life.

WARNING! Battery Handling:

When keys, ornamental chains, or other electric metals contact the battery terminals, it can cause damage or injury. Short-circuited battery terminals generate significant heat. Exercise care when carrying and using the battery; always place it in an insulated container, not a metal one.

1.4 EU Declaration Conformity & RF Exposure

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED declares this device complies with Directive 2014/53/EU. This product is allowed in all EU member states. A complete declaration of conformity can be obtained at www.pofungshop.com.

SAR tests are conducted according to CE standards. The max. SAR value reported is 1.122W/kg for face up and 1.302W/kg for body worn (25mm for face up, 0mm for body worn). Use of belt clips, holsters, and similar accessories should not contain metallic components to ensure compliance with CE exposure requirements.

Additional Warnings:

  • Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries properly.
  • Excessive sound pressure from earphones/headphones can cause hearing loss.
  • Adapter must be installed near the equipment and easily accessible.
  • Use only the provided or CE approved charger. Unauthorized adapters may cause explosion or damage.
  • Adapter information: Model: A318-050100W-EU2, Input: 100-240V~50/60Hz 0.2A Max, Output: 5.0V-1.0A 5.0W.
  • Do not store the device below -10°C or above 60°C.
  • Operating temperature range: -10°C to 60°C.

2. Package Contents

Upon unpacking, please verify that all items listed below are present. If any item is missing, contact your dealer.

  • 1 x BAOFENG UV-36 PRO Radio
  • 1 x Fast desktop charger
  • 1 x Antenna
  • 1 x Li-ion battery pack (2500mAh)
  • 1 x Belt clip
BAOFENG UV-36 PRO radio with included accessories: antenna, charger, Type-C cable, and belt clip.

Figure 2.1: BAOFENG UV-36 PRO with standard accessories.

3. Main Features

  • Si4732 Full-band Radio Receiver: Supports FM/AM/LSB/USB/CW modulation modes, MR channel, and VFO frequency mode.
  • Dual-Mode Bluetooth: Integrated Bluetooth audio (for headsets/PTT) and Bluetooth data (for wireless programming).
  • 2.0" TFT Large Screen: Full keypad and full open menu operations for easy navigation.
  • 10 Zones/1000 Channels Storage: Organize and manage channel groups efficiently.
  • Built-in Input Method: Supports local editing of channel names, receive/transmit frequencies.
  • Man Down Alarm: Configurable trigger modes (Tilt angle, delay time, pre-cue time).
  • Dual Watch & Dual Standby: Monitor two channels simultaneously.
  • Tri-Power Output: Adjustable 10W/5W/2W RF output (high, medium, low).
  • Characteristic Scanning Functions: Channel scanning, frequency scanning, CTCSS/DCS scanning.
  • Customizable Side Key 1: Functions include VOX, SEARCH, SCAN, Bluetooth Audio.
  • Frequency Settings: Supports frequency difference, direction, inverted frequency, and relay activation audio.
  • Wireless Copy Frequency: One-click quick copy to search and store another radio's transmission frequency and privacy code.
  • Type-C USB Charging: Convenient charging via Type-C port, compatible with power banks, laptops, and car chargers.
  • NOAA Weather Channel Support: Access to NOAA weather alerts and updates for outdoor and emergency use.
Two BAOFENG UV-36 PRO radios displaying key features like APP programming, audio connect, multi-band, 10W power, 1000 channels, VOX, Type-C charger, 2.0 inch large screen, NOAA weather, one key frequency copy, and DTMF.

Figure 3.1: Overview of BAOFENG UV-36 PRO features.

BAOFENG UV-36 PRO radio highlighting dual-mode Bluetooth capabilities for audio and programming, along with various receiver frequency ranges for SW, MW, LW, FM, and AM bands.

Figure 3.2: Dual-mode Bluetooth and frequency ranges.

Close-up of the BAOFENG UV-36 PRO's 2.0 inch TFT large display showing frequency and VFO information.

Figure 3.3: 2.0" TFT Large Display.

BAOFENG UV-36 PRO shown in various application scenarios such as hiking, hunting, camping, and climbing, demonstrating its wide usability.

Figure 3.4: Wide application scenarios.

4. Setup and Installation

4.1 Charging the Battery Pack

The Li-ion battery pack is not fully charged at the factory. Charge it before first use. For optimal performance, fully charge and discharge the battery two or three times.

Charging Procedure:

  1. Plug the AC adapter into an AC outlet.
  2. Connect the AC adapter cable to the DC jack on the charger. The indicator blinks orange, ready for charging.
  3. Plug the battery or the radio (with battery) into the charger. Ensure good contact with charging terminals. The indicator turns red.
  4. Charging takes approximately 2-5 hours. The indicator turns green when charging is complete.
  5. Remove the battery/radio from the charger once fully charged.

Note: If the radio is powered ON during charging, the indicator may not turn green even when fully charged, as the radio consumes energy. For accurate indication, charge with the radio OFF.

Type-C USB Charging:

The UV-36 PRO supports Type-C USB charging for convenience.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the charging port on your battery.
  3. Connect the other end to a wall power outlet, power bank, or laptop.
  4. An empty battery will be fully charged in approximately 4 hours.
  5. The battery meter on the LCD will animate to indicate charging.

Note: It is recommended to power OFF your radio while charging. If ON, you may not be able to transmit if the battery is completely empty. Allow at least one bar of charge before transmitting. For optimal battery life, remove the radio from the charger within 6 hours; do not store it connected to the charger.

Diagram showing multiple charging methods for the BAOFENG UV-36 PRO, including Type-C and standard USB chargers, connected to a wall adapter, power bank, and laptop.

Figure 4.1: Multi-charging methods (Type-C and USB).

4.2 Installation of Accessories

Antenna:

  • Installing: Screw the antenna into the connector on top of the transceiver clockwise until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.

Belt Clip:

  • Installing: Remove the two parallel screws above the battery on the back of the radio. Thread them through the holes on the belt clip and screw them back into the radio body.
  • Removing: Unscrew counter-clockwise to remove the belt clip.

Battery Pack:

Ensure the radio is turned OFF before attaching or removing the battery.

  • Attaching: Align the battery parallel with the radio body, with its lower edge about 1-2cm below the radio's edge. Slide the battery upward along the guide-rails until it clicks into place.
  • Removing: Press the battery release button (above the battery pack) while sliding the battery downward.

Additional Speaker/Microphone (Optional):

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

Diagram showing the connection points for an external speaker and microphone to the BAOFENG UV-36 PRO radio, including PTT, Mic, and Speaker jacks.

Figure 4.2: Speaker/Microphone connection diagram.

5. Operating Instructions

5.1 Radio Overview: Buttons and Controls

Diagram of the BAOFENG UV-36 PRO radio with numbered labels for its components: Antenna, PTT key, SK1 (Customize key), SK2 (Radio/Alarm key), MENU Key, Numeric keypad, Power/Volume knob, Speaker, Microphone, 2.0' TFT Color LCD, navigation keys, EXIT Key, Accessory jack, Battery release latch, Type-C charging port, and TX/RX Status LED.

Figure 5.1: BAOFENG UV-36 PRO Buttons and Controls.

  1. Antenna
  2. PTT key
  3. SK1 - Customize key (press and hold for monitor function)
  4. SK2 - Radio/Alarm key
  5. MENU Key
  6. Numeric keypad
  7. Power/Volume knob
  8. Speaker
  9. Microphone
  10. 2.0' TFT Color LCD
  11. Up/Down navigation keys
  12. EXIT Key
  13. Accessory jack
  14. Battery release latch
  15. Type-C charging port
  16. TX/RX Status LED
  17. Reserved interfaces

5.2 Basic Operations

Power On/Off:

  • To Turn On: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, then display a frequency or channel.
  • To Turn Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

Adjusting Volume:

  • To Increase: Turn the Volume/Power knob clockwise.
  • To Decrease: Turn the Volume/Power knob counter-clockwise.

Main Band/Sub Band Select:

In standby mode, press the A/B key to switch between the A (upper) and B (lower) displays.

VFO/Channel Switch:

Press and hold the MENU key to switch between VFO (Frequency) and Channel (MR) display.

Frequency (VFO) Mode:

Navigate up/down the band using the Up/Down keys. Input frequencies directly using the numeric keypad (e.g., for 436.61250 MHz, enter [4][3][6][6][1][2][5][0]).

WARNING! Transmitting on unauthorized frequencies is illegal and a serious offense.

Select a BANK:

The radio supports 10 banks, each holding up to 100 channels (total 1000 channels). Use the CPS program software to add zones and name banks. In standby mode, press MENU key to enter main menu >> BANK >> select a BANK.

Select a Channel:

In channel mode, with a bank selected, press the Up/Down keys to select a channel. Input channel numbers directly (e.g., for channel 12, input [0][1][2]).

Making a Call:

  • Channel Mode Call: Select a channel, then press and hold the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED illuminates.
  • Frequency Mode Call: Switch to VFO mode, input the desired frequency, then press and hold the [PTT] key to transmit. The red LED illuminates.
  • Receiving a Call: Release the [PTT] key. The green LED illuminates when receiving a call.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

Emergency Alert:

Press and hold the [SK2] key for 3 seconds to activate. The radio will emit a loud siren and the flashlight will flash. Press [SK2] again to exit. WARNING: Use only in actual emergencies.

Monitor:

Press and hold the [SK1] key to enter Monitor mode. This allows monitoring weak signals or signals with matched carriers but weak signaling. Release [SK1] to exit. If no signal is present, it will emit noise.

Keypad Lock:

Press and hold the # key for about two seconds to enable/disable. The radio can also be set to automatically lock after ten seconds via the menu.

Frequency Reversal:

A momentary press of the * key reverses transmit and receive frequencies. The screen will display "R".

TX Repeaters Tone:

Press [PTT] + [SK2] to send a 1750Hz repeater tone. This function is useful for communications through repeaters and works even with keypad lock enabled.

5.3 Advanced Features

Scanner:

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps; in Channel (MR) mode, it scans your channels. To enable, press and hold the # key for about two seconds. Change scanning direction with Up/Down keys. Press and hold # to exit.

  • Scan Modes: Time (stops, resumes after timeout), Carrier (stops, resumes after no signal), Search (stops on signal).
  • Frequency Ranger: Set precise start and end values for VFO frequency sweep (e.g., 144.000-146.000MHz).
  • Scan CTCSS/DCS: Search for CTCSS/DCS codes on a known frequency.
  • Sub-Code Scan Storage: Store scanned CTCSS/DCS codes as TX, RX, or both.

DTMF (Dual-Tone Multi-Frequency):

Used for automation systems and remote control (e.g., activating amateur radio repeaters). The radio supports full DTMF implementation (A, B, C, D codes). Press the desired number keys while holding the PTT key to send DTMF codes.

DTMF Frequencies and Codes
1209Hz 1336Hz 1477Hz 1633Hz
697Hz 1 2 3 A
770Hz 4 5 6 B
852Hz 7 8 9 C
941Hz * 0 # D

Dual Watch:

Allows monitoring two channels simultaneously. To enable/disable: Press MENU > Radio Settings > 15 Dual Watch. Select ON/OFF. The 'D' icon appears on the screen when enabled.

Voice-Activated Transmit (VOX):

Enables hands-free transmission. To enable: Enter MENU > 4 (Radio Settings) > 4 (Vox Switch). Set Vox Level (1-9, lower value = higher sensitivity). Press MENU to save. The 'V' icon appears when enabled.

Define SK1 as a Search function via CPS software or radio menu. Briefly press [SK1] to search. The radio will display "SEARCH SEEK...". If an effective frequency is received, it will be displayed along with CTCSS/DCS values if present.

Manual Programming (Channels Memory):

Store commonly used frequencies. The radio has 1000 channels across 10 zones. To program a simplex channel with CTCSS tone (e.g., RX=432.6500 MHz, R-CTCSS 123.0 in Channel 100):

  1. Change to VFO mode.
  2. Enter MENU > 5 (Program Channel) > 1 (CH.NAME).
  3. Enter the channel number (e.g., 100).
  4. Set RX frequency (e.g., 43265000).
  5. Set RX CTCSS (e.g., 123.0).
  6. Save the settings.

6. Bluetooth Function

The UV-36 PRO features dual-mode Bluetooth for enhanced wireless capabilities.

6.1 Bluetooth Audio:

Connects with Bluetooth headsets and Bluetooth PTT devices for hands-free communication. This mode allows for clear, noise-reduction call audio and real-time transmit/receive via wireless earphones.

  • BT Device: The radio automatically searches for available Bluetooth devices.
  • BT Voice: Controls the volume level of the Bluetooth headset (5 levels).
  • BT Mic Gain: Controls the microphone gain of the Bluetooth headset (5 levels).

Note: The Bluetooth audio function can only be used with Bluetooth PTT and Bluetooth earphones.

6.2 Bluetooth Wireless Programming:

The UV-36 PRO allows wireless frequency programming via a dedicated APP. This eliminates the need for cables and complex software installations.

  1. Press MENU > 3 (Bluetooth) > Bluetooth Mode.
  2. Select "Bluetooth Data". The Bluetooth icon will appear on the screen.
  3. Download and install the "baofengradio" APP from www.baofengradio.com (or scan the QR codes below).
  4. Open the APP, enable Bluetooth and location on your phone.
  5. Select "Baofeng" brand and "SW9" model in the APP.
  6. Connect the radio via the APP.
  7. Once connected, you can read and write frequencies and program channel information, frequency mode, and other optional functions.
Smartphone screen showing the 'Ola Radio' app interface for programming the BAOFENG UV-36 PRO, with options for channel settings, frequency mode, and writing data to the device.

Figure 6.1: APP Programming and Audio Connect.

Scan to download baofengradio APP:

QR code for iOS App download. QR code for Android App download.

7. Broadcast AM/FM/SW/LW/RDS Radio Receiver

The UV-36 PRO includes a broadcast radio receiver function (optional, not standard function).

7.1 Frequency Ranges:

  • FM: 65-108MHz (RX)
  • AM: 108-136MHz (RX)
  • SW (Shortwave): 2.3-26.1MHz (RX)
  • MW (Mediumwave): 520-1710KHz (RX)
  • LW (Longwave): 153-279KHz (RX)
  • LSB/USB/CW: 150K-29999KHz

Note: You must install the full-band antenna firmly and reliably before using the radio receiver function.

7.2 Receiver Operations:

  • Short press SK2 to quickly enter the radio receiver mode.
  • Press and hold MENU to switch between VFO (frequency) or MR (memory) mode.
  • In VFO mode, enter frequency directly or use Up/Down keys to search for broadcast channels.
  • Press # to automatically search for radio channels.
  • Press MENU to change radio modes (AM, FM, LSB, USB, CW).
  • Press # to change Step, Bandwidth, Gain, and Beat Frequency options.
  • Press SK2 or EXIT key to exit radio mode.
BAOFENG UV-36 PRO radio held in hand, displaying its screen and highlighting its new AM/SW/MW/LW receiver capabilities with specific frequency ranges for each band.

Figure 7.1: AM/SW/MW/LW Receiver.

BAOFENG UV-36 PRO radios illustrating SW, MW, and LW receive modes with corresponding images of a rescue operation, a mountain landscape, and a fishing boat, indicating various applications.

Figure 7.2: SW/MW/LW Receive Modes.

8. Maintenance

8.1 Battery Maintenance and Storage:

  • Clean the charging connector regularly with a dry cloth.
  • Charge the battery between 5°C and 40°C.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire or expose it to direct sunlight/heat sources.
  • Do not squeeze, penetrate, or remove the battery housing.
  • For storage, discharge the battery to about 80% and keep it in a low-temperature, dry environment, away from hot places and direct sunlight.

8.2 Radio Maintenance:

  • Do not attempt to open or realign the radio; this will void the warranty.
  • Avoid storing the radio in direct sunlight, hot areas, or dusty/dirty environments.
  • Keep the radio dry; moisture can corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off power and remove the battery/charger.
  • Do not transmit without an antenna.

8.3 Transportation Instructions:

  • Damaged batteries must not be transported.
  • Separate batteries from metal parts or each other if transporting multiple batteries to avoid short circuits.
  • The radio must be switched off and secured against accidental activation if the battery is attached.
  • Declare shipment contents and use a Battery Shipping Label. Consult your hauler for local regulations.

9. Troubleshooting Guide

If you encounter issues with your radio, refer to the table below for common problems and solutions.

Phenomena Analysis Solution
Cannot turn on the radio. Battery improperly installed, battery power low, poor battery contact. Remove/reattach battery, recharge/replace battery, clean battery contacts.
Weak or intermittent voice during reception. Volume level low, loose/incorrectly installed antenna, blocked speaker. Increase volume, turn off radio/reattach antenna, clean speaker surface.
Cannot communicate with other group members. Inconsistent frequency/signaling type, too far from other members. Verify TX/RX frequency/signaling type, move closer to other members.
Hear unknown voices or noise. Interrupted by other radios on same frequency, analog mode without signaling. Change frequency/adjust squelch level, request dealer to set signaling.
Unable to hear due to too much noise/hiss. Unfavorable position (blocked by buildings/underground), external disturbance. Move to open/flat area, restart radio, stay away from interference sources.
Radio keeps transmitting. VOX turned on, headset not installed correctly. Turn off VOX, check headset placement.

Note: If these solutions do not resolve your issues, please contact your dealer for technical support.

10. Specifications

Feature Specification
Model Number UV-36 PRO (SW-9)
FCC ID 2AJGM-SW9
Brand Name BAOFENG
Origin Mainland China
Walkie Talkie Type Portable
Material Plastic
Is Display Yes (2.0" TFT Large Screen)
Waterproof / Water-Resistant No
Output Power (W) 5W-10W (Tri-Power)
Maximum Range 5km-10km
Storage Channel 1000
Battery Capacity (mAh) 2500mAh
Battery Included Yes
Rechargeable Battery Included Yes
High-concerned chemical none
Use others
Amateur Radio TX Frequency 144-146MHz, 430-440MHz
Amateur Radio RX Frequency 108-136MHz, 136-174MHz, 200-260MHz, 350-390MHz, 400-600MHz
FM (RX) Frequency 87.5-108MHz
AM (RX) Frequency 526.5 kHz to 1606.5 kHz
BT/BLE Frequency 2402-2480MHz
Max. Transmit Power (Amateur Radio) 36.10dBm
Max. Transmit Power (BT) 2.87dBm EIRP
Max. Transmit Power (BLE) 3.52dBm EIRP
Package Dimensions (L x W x H) 22cm x 20cm x 10cm
Package Weight 0.75 kg

11. User Tips

  • Model Clarification: While marketed as UV-36 PRO, the device may also be labeled as BAOFENG SW-9, which is its FCC ID designation (2AJGM-SW9). Both refer to the same product.
  • Bluetooth Programming: For wireless programming, ensure you download the official "baofengradio" APP from www.baofengradio.com. This is crucial for customizing frequencies and settings.
  • Antenna Selection: If you plan to operate on specific frequency bands, especially for shortwave (HF) reception, consider researching and using an antenna optimized for those bands to enhance performance.
  • Initial Setup: Take the time to fully charge and discharge the battery a few times before regular use to ensure it reaches its optimal operating capacity.
BAOFENG UV-36 PRO radio lying on a surface next to a small manual that shows 'Amateur Radio SW-9 USER'S MANUAL' and a QR code for the Bluetooth software.

Figure 11.1: Radio with manual showing 'SW-9' designation.

12. Warranty and Support

12.1 Disclaimer:

The Company endeavors to ensure the accuracy and completeness of this manual. However, no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed without the prior written consent of the Company. We do not guarantee the accuracy, validity, timeliness, legitimacy, or completeness of third-party products and content mentioned herein.

12.2 Manufacturer Contact Information:

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY

Print version: SW9F (UV36) V1.0

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.