Introduction
Thank you very much for choosing our products! The BAOFENG UV-36 is a multi-functional handheld amateur radio designed to meet diverse communication needs. It combines the latest radio communication technology with a robust mechanical framework, making it suitable for professional teams (such as those in pastoral areas, farms, hunting, forest protection, and tactical training) as well as leisure users who wish to stay connected with friends and family.
This product aims to bring convenience to your work, life, and leisure activities. To ensure maximum enjoyment and to prevent personal injury or property damage due to improper operation, please read this manual and any accompanying safety information carefully before use.
Important Safety Information
Before using this walkie-talkie, please read carefully the following instructions for safe use of the walkie-talkie in radiofrequency radiation and Product Safety.
RF Radiation Information
This product is intended for professional applications that meet RF radiation requirements. Users must be aware of the hazards of RF radiation and take appropriate measures to meet the requirements of RF radiation limits.
Common Sense in RF Radiation
RF refers to electromagnetic frequency that can be radiated into space. It is a technology widely used in communication, medical treatment, and food processing. It will produce some RF radiation during use.
Control and Operating Instructions of RF Radiation
To maximize product performance and ensure compliance with radiation limits in relevant occupational or controlled environments, the transmission time shall not exceed 50% of the rated factor. Follow these instructions:
- RF radiation is generated only during transmission (speech), not during reception (listening) or standby.
- The distance between the terminal and the body during transmission should be at least 2.5 cm.
Prohibited Uses
It is strictly prohibited to use this product in the following places or situations to avoid property damage or personal injury:
- Do not use or charge batteries in places where fuel, chemicals, explosive gases, or other inflammable and explosive materials are stored. Any disassembly and installation is strictly prohibited.
- Do not use this product in or near blasting operation areas.
- Do not use this product near medical equipment or electronic equipment sensitive to RF signals.
- When driving, the driver is strictly prohibited from holding this product to transmit signals.
- It is strictly prohibited to use this product in places where wireless communication equipment is prohibited.
- Turn off the walkie-talkie before boarding an aircraft. Any use of the walkie-talkie must comply with airline policy or crew instructions.
User Safety Information
When using this product, observe the following precautions to avoid property loss or personal injury:
- Do not use unapproved or damaged parts.
- While transmitting, keep the radio in a vertical position and the microphone about 5cm from your mouth. Keep the two-way radio at least 2.5cm from the head or body during transmitting.
- Do not use high decibel volume for long periods.
- In automobiles with airbags, do not place the two-way radio in the inflation area of the airbags.
- Do not place this product within reach of children and pets.
- Use the product within the specified operating temperature range.
- If transmitting for a long time, the fuselage may get hot. Allow the product to cool down.
- Press buttons with consistent strength; do not use excessive force.
- Maintenance work can only be carried out by professional technical personnel; unauthorized assembly/disassembly is prohibited.
- If wearing the portable walkie-talkie on your body, ensure the antenna is at least 2.5cm away from the body when transmitting.
Battery Safety Precautions
Forbidden to Recharge
Do not recharge in the following places or situations to avoid property damage or personal injury:
- Do not recharge or replace batteries in places where fuel, chemicals, explosive gases, or other inflammable and explosive materials are stored.
- If the battery or terminal is contaminated with moisture, wipe it with a clean cloth before charging. Otherwise, recharging is forbidden.
- Do not charge the battery if it leaks, deforms, or overheats.
- Do not use an unauthorized charger for charging.
- Do not charge near strong radiation sources.
- Do not overcharge the battery; otherwise, battery life will be affected.
Battery Maintenance
To ensure normal battery operation and prolong its life, observe the following precautions:
- Dust accumulated on the positive and negative electrodes may affect normal charging. Clean the battery with a clean dry cloth promptly.
- It is recommended to charge the battery between 5°C and 40°C. Charging at too high or too low a temperature can shorten battery life and cause leakage.
- If charging a terminal equipped with a battery, turn off its power during charging to ensure proper charging.
- Do not plug or remove the power supply and battery during charging to avoid interfering with the normal charging process.
- Do not discard the battery in fire.
- Do not expose the battery to direct sunlight for long periods or place it near other heat sources.
- Do not squeeze, prick, or remove the battery shell without authorization.
Transportation Information
- Do not transport damaged batteries.
- Ensure that batteries in the packing case do not short-circuit. If there are multiple batteries, pack each separately to avoid short-circuit.
- If the walkie-talkie has a built-in battery, it must be turned off, and measures taken to prevent accidental startup.
- Transport documents must state the details of the goods and be marked with the battery transport label on the packing case. Check with your carrier for local laws, regulations, and other information.
Packing List
The packing box contains the following items. If any item is missing or damaged, please contact your dealer.
- 1 x UV-36 Walkie-talkie
- 1 x Li-ion battery
- 1 x Adapter
- 1 x Intelligent charger
- 1 x User's Manual
- 1 x Antenna
- 1 x Belt Clip
- 1 x Handstrap
Note: For the antenna frequency band, see the label on the color ring at the bottom of the antenna. If the frequency band is not specified, refer to the specific frequency band on the walkie-talkie.
Product Overview






Familiarization with the Product
This section details the physical components and controls of your BAOFENG UV-36 radio.

Control Keys and Buttons

| Button | Function |
|---|---|
| 【PTT】Transmit button | Press to transmit, speak into microphone. Release to receive. |
| 【Flashlight/MONI】button | Short press: Turn on/off flashlight. Long press: Activate/deactivate monitor function. |
| 【VFO/MR】Frequency/channel switch button | Switch between frequency mode and channel mode. |
| 【A/B】Frequency Band A/B switch button | Switch between Frequency Band A (upper) and Frequency Band B (lower). Indicates transmitting frequency band. |
| 【SOS/FM Radio】button | Short press: Turn on/off FM radio. Long press: Activate/cancel alarm function. |
| 【MENU】button | Activate menu mode, enter menu, and select menu items. |
| 【▲】/【▼】UP/DOWN button | Frequency mode: Change frequency. Channel mode: Switch channels. Menu status: Navigate menu items/values. Scanning status: Change scanning direction. |
| 【EXIT】button | Clear input information. In FM mode: Switch frequency range. In scanning status: Change scanning direction. |
| *, #, 0-9 number buttons | Numeric input for frequency, channel, menu items. * key for scanning. # key for keyboard lock. PTT + number for DTMF. |
| 【PTT】+【FM】 | Press to send 1750HZ signaling in transmitting state. |
Numeric Keypad
The numeric keypad is used to enter messages or select channels. When in transmission mode, press and hold the PTT key while inputting numbers to send the corresponding DTMF code.
- * SCAN button: In standby mode, short press to switch high, medium, and low power. Long press to lock or unlock the keyboard.
- 0 SQL button: In standby mode, long press to display the current battery level.
- # button: In standby mode, short press to activate or disable frequency reversal. Long press to activate the scan function.
LCD Icons Description

| No. | Description | No. | Description |
|---|---|---|---|
| 1 | Transmission power icon (High/Low Power are optional) | 10 | The current CTCSS is enabled. |
| 2 | The VOX function is enabled. | 11 | The current DCS is enabled. |
| 3 | The frequency difference in a positive direction. | 12 | The current operating band indicator (A/B band indicator) |
| 4 | The frequency difference in a negative direction. | 13 | Battery level indicator |
| 5 | Frequency reversal (The reversal of receive and transmit frequencies) | 14 | The last two digits in the frequency decimal point. |
| 6 | Work in narrowband mode | 15 | In channel mode, the current channel number is displayed. |
| 7 | The dual watch function is enabled. | 16 | Frequency of current working segment A |
| 8 | The keyboard lock function is enabled. | 17 | Frequency of current working segment B |
| 9 | Field strength icon |
Setup
Accessory Installation
Antenna Installation/Removal
To install: Turn off the walkie-talkie, insert the antenna into the mounting hole, and rotate it clockwise until secure.
To remove: Rotate the antenna anticlockwise and pull it out.
Note: Do not shake the product by the top of the antenna, as this may reduce its performance and service life.
Battery Installation/Removal
Before installing or removing the battery, ensure the walkie-talkie is completely off by turning the power/volume knob counterclockwise.
Battery Installation:
- Align the battery with the battery installing seat on the back of the two-way radio.
- Press the battery into the walkie-talkie forcefully.
- Push the battery toward the top until the "battery latch" locks the battery.
Battery Removal:
- Turn off the two-way radio. Move the battery lock to the unlocking position and press it.
- Slide the battery downward until it is taken out of the battery installing seat.
Installation of External Headphone/Microphone
Open the headphone cover and insert the headphone plug into the headphone jack.

Note: Install attachments correctly to avoid affecting external headphone or programming functionality.
Charging the Battery
Note: Ensure the product is off when charging.
Charge the battery using the specified charger. The charger's indicator light shows the charging status:
- Plug the power adapter into a power outlet.
- Plug the other end of the power adapter into the socket on the back of the charging cradle.
| Indicator Light | Status |
|---|---|
| Red light | In charging |
| Green light | Charging is completed |
Note:
- For best battery performance, charge for a minimum of 6 hours on the first charge.
- Refer to the Battery Safety Precautions for necessary battery safety information.
Battery Level Indicator
This feature shows the remaining battery amount.
| Icon | Battery Level |
|---|---|
| Full bars | High |
| Medium bars | Medium |
| Low bars | Low |
| Empty/Flashing | Insufficient |
If the battery icon indicates insufficient power (flashing outer frame), the walkie-talkie is prohibited from transmitting. You can press the [0 SQL] key to obtain battery voltage information (e.g., BATT 7.8V).
Operating Instructions
Basic Operation
Power On/Off
To turn on: Rotate the 【Power Switch / Volume Control】 knob clockwise until you hear a "click" and a short beep.
To turn off: Rotate the knob counterclockwise until you hear a click.
Adjusting Volume
After turning on, rotate the [Power switch / volume control] knob clockwise to increase reception volume, and counterclockwise to reduce it.
Frequency Mode and Channel Mode Selection
In standby mode, press [VFO/MR] to switch between frequency mode and channel mode. In channel mode, the channel number is displayed on the right. In frequency mode, the channel number disappears.

Channel Selection
In channel mode, press ▲ or ▼ to select a channel up or down. Long pressing ▲ or ▼ will quickly switch channels. If voice prompt is enabled, the radio will broadcast the channel number.
Note: In channel mode, you can quickly select a familiar channel by directly inputting its number via the numeric keypad.
Call
For best reception volume, keep the microphone 2.5cm to 5cm from your mouth.
- Making a call: Select a channel, then press and hold the [PTT] key. The radio will be in transmitting state (red light on). Speak into the microphone.
- Call reception: Release the [PTT] button. A prompt tone will sound, and the radio will be in receiving state (green indicator steady on).
Note: In frequency mode, input the working frequency within the allowed range via the numeric keypad, then press and hold [PTT] to transmit. The red indicator will be on. Before initiating a call, you can temporarily switch power by pressing the 【#/】 key. "H" or "L" on the display indicates high or low power transmission.
Monitor Function
In standby mode, long press the [LAMP/MONI] key to activate the monitor function. Release the key to exit.
Flashlight Function
Turn on the walkie-talkie, short press [LAMP/MONI] to turn on the flashlight. Press again for the lamp to flash. Press a third time to turn off the flashlight.
Keyboard Lock
To lock: When the keyboard is not locked, long press the 【#】 key. The lock icon will appear on the first line of the screen.
To unlock: In the key lock state, long press the 【#】 key to release the lock.
Advanced Function Operations
FM Radio Function
Turn on the walkie-talkie and press the 【FM/SOS】 key to enter FM radio mode. The screen will display the FM frequency.

To search: Press ▲ or ▼ to search for FM radio channels by preset step frequency, or press [*/SCAN] for automatic search.
To exit: Press the 【FM/SOS】 key.
Audible and Visual Alarm Function
Turn on the walkie-talkie and long press 【FM/SOS】 to activate the alarm. The alarm light flashes, and the loudspeaker emits an alarm sound.
Note: Alert mode can be set through Menu 32. Options include TONE, CODE, and SITE.
Repeater Activated Audio
The walkie-talkie can activate a dormant repeater by transmitting repeater activation audio, even when the channel is locked.
To activate: Press the [PTT] key, then press the [FM/SOS] key to transmit 1750Hz audio.
Note: Repeater activated audio can be set in Menu No.41. This machine offers 1000Hz, 1450Hz, 1750Hz, and 2100Hz options.
Frequency Reversal Function
In standby mode, press the [*/SCAN] key to reverse the receive and transmit frequencies. "R" will be displayed at the top of the screen. This feature is often used for repeater channels.
Channel Scan
In channel mode, long press the [*/SCAN] key to enter channel scan mode. The radio scans channels and pauses on an active channel until it is idle for 5 seconds before resuming. Press [PTT] to initiate a callback while paused. Press [*/SCAN] to exit scan.
Note: The scan recovery mode can be set through Menu 18 (time, carrier, or search).
Frequency Scan
In frequency mode, long press the [*/SCAN] key to enter frequency scan mode. The radio automatically pauses on an active frequency point until it is idle for 5 seconds before resuming. Press [PTT] to initiate a callback while paused. Press [*/SCAN] to exit scan.
CTCSS/CDCSS Scan
In frequency mode, disable dual watch (Menu 7 TDR). Set the receiving frequency to ensure signal reception.
(1) R-CTCS:
- In frequency mode, enter the correct received frequency.
- Press [MENU] to enter MENU function.
- Press [1][1] successively to enter menu 11 (CTCSS), or navigate using ▲/▼.
- Press [MENU] to start CTCSS scan (ensure CTCSS is enabled, not OFF).
- Press [EXIT] to exit CTCSS Scan.
(2) R-DCS:
- In frequency mode, enter the correct received frequency.
- Press [MENU] to enter MENU function.
- Press [1][0] successively to enter menu 11 (DCS), or navigate using ▲/▼.
- Press [MENU] to start DCS scan (ensure DCS is enabled, not OFF).
- Press [EXIT] to exit DCS Scan.
VOX (Voice Activated Transmission)
When VOX is enabled, you don't need to press PTT to transmit. The radio automatically transmits when it detects speech and stops when speech ceases. This is useful in workplaces where pressing PTT is difficult.
Operation:
- Press [MENU] to enter MENU function.
- Press [4] successively to enter menu 4 (VOX), or navigate using ▲/▼.
- Press [MENU] to enter VOX level setting. Use ▲/▼ to select 1-10 (higher value = higher sensitivity).
- Press [MENU] to save and return.
To disable VOX, repeat steps and select OFF.
Keyboard Lock (Automatic)
The keyboard lock prevents accidental function activation. You can set an automatic keyboard lock.
Operation:
- Press [MENU] to enter MENU function.
- Press [2][4] successively to enter menu 24 (AUTOLK), or navigate using ▲/▼.
- Press [MENU] to enter setting. Use ▲/▼ to select ON.
- Press [MENU] to save and return.
To disable, repeat steps and select OFF.
Note: If automatic keyboard lock is on, the radio will lock automatically after 10 seconds of no keyboard operation.
Keyboard Lock (Manual)
Operation:
- In standby mode, long press the [#] key for more than 2 seconds to enable keyboard lock (voice prompt "lock").
- Repeat the previous step to disable keyboard lock (voice prompt "unlock").
Dual Standby
In dual standby mode, the radio can receive on both A and B channels. The icon "S" will be displayed.
Operation:
- Press [MENU] to enter MENU function.
- Press [7] to enter menu 7 (TDR), or navigate using ▲/▼.
- Press [MENU] to enter dual standby setting. Use ▲/▼ to select ON.
- Press [MENU] to save and return.
To disable, repeat steps and select OFF. The "S" icon will disappear.
Lock Dual Standby Transmission Channels
- Press [MENU] to enter MENU function.
- Press [3][4] successively to enter menu 34 (TDR-AB).
- Press [MENU] to select.
- Press ▲ or ▼ to select A or B.
- Press [MENU] to confirm.
- Press [EXIT] to exit.
To temporarily unlock without changing Menu 34, toggle by pressing [A/B] keys before pressing PTT.
Channel Deletion
- Press [MENU] to enter MENU function.
- Press [2][8] successively to enter menu 28 (DEL-CH), or navigate using ▲/▼.
- Press [MENU] to enter channel deletion. Use ▲ or ▼ to select the channel to delete.
- If the channel number has a "CH-" prefix, it contains parameters and can be deleted.
- If no "CH-" prefix, the channel is empty and can be stored directly.
- Press [MENU] to confirm deletion, save, and return.
- If the channel is empty, press [MENU] to return directly.
Manual Programming
All channel parameters (receive/transmit frequency, R-CTCS, T-CTCS, transmit power, bandwidth, PTT-ID, busy lock, signal code, scan add, channel name) can be set in frequency mode, except for scan add and channel name which require frequency software. Parameters are then stored in the specified channel number via Menu 27 (Save Channel).
Frequency Mode and Channel Mode
Frequency mode is also called VFO mode; Channel mode is also called MR mode. In standby mode, press [V/M] to switch between modes. Frequency mode is the basic mode for frequency editing.
Example 1: Edit a Relay Channel with CTCSS
Create a new storage channel on channel 10. Receive frequency: 432.55000, transmit frequency: 437.55000 (difference: +5.0MHz), T-CTCSS: 123.0.
Steps:
- Press [V/M] to switch to frequency mode (right channel serial number disappears).
- Press [MENU][2][8][MENU][1][0][MENU][EXIT] to delete existing data on Channel 10.
- Press [MENU][1][3][MENU][1][2][3][MENU][EXIT] to select T-CTCSS (123.0).
- Manually input the receiving frequency (e.g., 432.55000).
- Press [MENU][2][7][MENU][1][0][MENU] to enter storage channel (e.g., channel 10).
- Press [EXIT] to return.
- Manually input the transmitting frequency (e.g., 437.55000).
- Press [MENU][2][7][MENU][1][0][MENU] to enter storage channel (e.g., channel 10).
- Press [EXIT] to return.
- Press [V/M] to switch to channel mode (right channel number reappears).
Example 2: Edit a Simplex Channel with CTCSS (Same Receive/Transmit Frequency)
Create a new storage channel on channel 10. Receive/transmit frequency: 432.66250, T-CTCSS: 123.0.
Steps:
- Press [V/M] to switch to frequency mode (right channel serial number disappears).
- Press [MENU][2][8][MENU][1][0][MENU][EXIT] to delete existing data on Channel 10.
- Press [MENU][1][3][MENU][1][2][3][MENU][EXIT] to select T-CTCSS (123.0).
- Press [A/B] to select the AB pointer to A.
- Manually input the transmitting frequency (e.g., 432.66250).
- Press [MENU][2][7][MENU][1][0][MENU] to enter storage channel (e.g., channel 10).
- Press [EXIT] to return.
- Press [V/M] to switch to channel mode (right channel number reappears).
Repeater Frequency Programme
These instructions assume you know the repeater's transmitting and receiving frequencies and have the right to use them.
- Press [V/M] to switch to frequency mode (right channel serial number disappears).
- Enter the transmit/receive frequency of the repeater via the keyboard.
- Press [MENU] to enter MENU function.
- Press [2][6] successively to enter menu 26 (OFFSET). Press [MENU] to access the function and use the keypad to enter the specified frequency difference.
- Press [MENU] to confirm and save.
- Press [2][5] successively to enter menu 25 (SFT-D). Press ▲ or ▼ to select + (positive) or - (negative) frequency difference.
- Press [MENU] to confirm and save.
- Press [EXIT] to return.
If all goes well, you should be able to make test calls through the repeater.
Function Menu
The radio features a comprehensive menu system for configuration. You can access menu functions using arrow keys or by directly entering menu numbers.
Basic Use of Menus (Arrow Keys)
- Press [MENU] to enter MENU function.
- Press ▲ or ▼ to select menu items.
- Once the desired item is found, press [MENU] to select it.
- Press ▲ or ▼ to select parameters.
- To confirm selection, press [MENU] to save settings and return to main MENU. To cancel changes, press [EXIT] to reset the item and exit.
- To exit the menu at any time, press [EXIT].
Quick Operation of Menus (Numeric Keypad)
Each menu item has an associated number for direct access.
- Press [MENU] to enter MENU function.
- Enter the menu item number on the numeric keypad.
- Press [MENU] to enter the menu item.
- Press ▲ or ▼ to select parameters.
- To confirm selection, press [MENU] to save settings and return to main MENU. To cancel changes, press [EXIT] to reset the item and exit.
- To exit the menu at any time, press [EXIT].
| Menu No. | Name of Function | Settings | Description of Settings |
|---|---|---|---|
| 0 | Squelch | 0-9 | Squelch level. Lower level is easier to interfere; higher level sensitivity is worse. Middle setting is recommended. |
| 1 | Step Frequency | 2.5K, 5.0K, 6.25K, 10.0K, 12.5K, 20.0K, 25.0K, 50.0K | In frequency mode, changes the step value of frequency when UP/DOWN keys are pressed. |
| 2 | Transmit Power | HIGH, MID, LOW | Sets the radio's transmit power. |
| 3 | Power Save | OFF, 1, 2, 3, 4 | Turns off power saving or sets power save ratio (1:1, 1:2, 1:3, 1:4 modes). |
| 4 | Vox Level | OFF, 1-10 | Turns off VOX or sets VOX sensitivity level. |
| 5 | Channel Bandwidth | WIDE, NARR | Sets radio to wideband or narrowband mode. |
| 6 | Backlight | OFF, 1-10 | Turns off backlight or sets automatic backlight duration. |
| 7 | Dual Standby | OFF, ON | Turns off or on dual standby mode. |
| 8 | Beep Prompt | OFF, ON | Turns off or on beep prompt. |
| 9 | Time-out timer | 15-600 (in 15-step increments) | Sets maximum transmit time when PTT is pressed. |
| 10 | Rx-DCS | OFF, D023N-D754I | DCS not set or standard sequence of DCS. |
| 11 | Rx-CTCSS | OFF, 67.0HZ-254.1HZ | CTCSS not set or standard sequence of CTCSS (can be typed directly). |
| 12 | Tx-DCS | OFF, D023N-D754I | DCS not set or standard sequence of DCS. |
| 13 | Tx-CTCSS | OFF, 67.0HZ-254.1HZ | CTCSS not set or standard sequence of CTCSS (can be typed directly). |
| 14 | VOICE | OFF, CHI, ENG | Turns off voice prompt or sets prompt language to Chinese/English. |
| 15 | ANI (Automatic Number Identification) | PC software only | Can only be set by PC software. |
| 16 | DTMF | OFF, DT-ST, ANI-ST, DT+ANI | Controls sound when DTMF codeword is sent (manual or automatic). |
| 17 | Signal Code | 1-15 | Signal code (PC software only). |
| 18 | Scan Mode | TO, CO, SE | Time-based scan, Carrier scan, Search scan. |
| 19 | Dual Standby PTT-ID | OFF, BOT, EOT, BOTH | Controls when PTT sends code (off, beginning of transmission, end of transmission, both). |
| 20 | PTT-LT | 0-50 (Unit: MS) | Delay time before automatic sending code. |
| 21 | MDF-A | FREQ, CH, NAME | In channel mode, displays A channel frequency, channel number, or channel name (PC software only). |
| 22 | MDF-B | FREQ, CH, NAME | In channel mode, displays B channel frequency, channel number, or channel name (PC software only). |
| 23 | Busy Lockout | OFF, ON | Allows transmission when channel is occupied or prohibits it. |
| 24 | Automatic Keylock | OFF, ON | Turns off or on automatic keyboard lock. |
| 25 | Direction | OFF, +, - | In frequency mode, no frequency difference or sets positive/negative difference. |
| 26 | Offset | 00.000-69.990 | Frequency difference between transmitted and received frequencies. |
| 27 | Channel Storage | 000-127 | Indicates channel number to be saved. "CH-" prefix means channel has parameters. |
| 28 | Channel Delete | 000-127 | Deletes channel parameters for specified channel. No "CH-" prefix means channel is empty. |
| 29 | Backlight Selection in Standby Mode | OFF, BLUE, ORANGE, PURPLE | Turns off backlight or sets blue, orange, or purple backlight in standby mode. |
| 30 | Receive Backlight | OFF, BLUE, ORANGE, PURPLE | Turns off backlight or sets blue, orange, or purple backlight in receive state. |
| 31 | Transmit Backlight | OFF, BLUE, ORANGE, PURPLE | Turns off backlight or sets blue, orange, or purple backlight in transmit state. |
| 32 | Alarm Mode | SITE, TONE, CODE | Sets alarm mode to on-site, tone, or code. |
| 33 | Frequency Band Selection | VHF, UHF | Sets working frequency band to 136-174 MHz (VHF) or 400-520 MHz (UHF). |
| 34 | Dual Watch to Transmit Selection | A, B | In dual watch state, selects A or B segment for transmitting/receiving. |
| 35 | Tail Tone Elimination | OFF, ON | Controls whether radio sends code after PTT release to confirm signal transfer. |
| 36 | Repeater Tail Tone Elimination | OFF, 1-10 | Adjusts delay to eliminate noise when transmitting through a repeater. Set to OFF if no noise. |
| 37 | Delay Time of Repeater | OFF, 1-10 | Adjusts noise time to confirm repeater retransmission. Set to OFF if no noise. |
| 38 | Power On Display | FULL, MGS | Sets screen display character or model on power-on. |
| 39 | Call End Prompt Tone | ON, OFF | Enables or disables prompt tone when PTT key is released. |
| 40 | Reset | VFO, ALL | Initializes menu settings or all menu and channel settings. |
| 41 | Repeater Activates Tone | 1000Hz, 1450Hz, 1750Hz, 2100Hz | Sets tone frequency for activating repeater (press PTT then FM/SOS). |
Maintenance and Clean
Maintenance
- Do not puncture or scratch this product with hard objects.
- Do not store the radio in an environment containing corrosive electronic circuit material.
- Do not directly lift the antenna or an external microphone when carrying or using the radio.
- Cover the appendage interface cover when attachments are not used.
Cleaning
Note: Turn off the radio and remove the battery before cleaning.
- Use a clean, dry cloth or brush to wipe off the radio surface and dust from the charging pole.
- After long-term use, walkie-talkie buttons, control knobs, and chassis may get dirty. Use neutral detergent (avoid strong corrosive chemicals) and a wet cloth to clean.
- After cleaning, ensure the radio is completely dry before use.
Troubleshooting Guide
| Malfunction | Solution |
|---|---|
| Radio has no power supply, cannot start. | Battery may be run out or improperly installed. Charge or replace battery, then remove and reinstall. |
| Battery power does not last long after charging. | Battery has reached end of life (approx. 300 cycles). Replace battery. |
| Radio cannot talk to other group members. | Ensure same frequency and CTCSS/DCS. Ensure you are within range of other walkie-talkies. |
| Communication distance is too close. | Ensure antenna is in good contact and is original. Confirm battery voltage is normal. |
| Other (non-member) voices heard on channel. | Change CTCSS/DCS. All walkie-talkies in the group must use the same new settings. |
| Radio communication is noisy. |
|
If the above methods do not resolve your problem, or you encounter other issues, please contact your local distributor for technical support.
Technical Specifications
All specifications may be modified without prior notice or liability.
| Parameter | Value |
|---|---|
| Memory Channel | 128 Group |
| Channel Spacing | 25KHz (Wide), 12.5K (Narrow) |
| Operating Voltage | DC 7.4V (Rechargeable lithium battery) |
| Frequency Stability | ±2.5ppm |
| Operating Temperature | -20 ~ +60℃ |
| Antenna Impedance | 50Ω |
| Transmit Current | ≤2.2A |
| Modulation (Wide/Narrow) | 16KΦF3E / 11KΦF3E |
| Stray Power | ≤7.5uW |
| Adjacent Channel power | ≤-65 dB/≤-60 dB |
| Signal-to-noise (wide/narrow) | ≥-45dB /≥-40dB |
| Modulation Sensitivity | 8-12mV |
| Dimensions | 62(W)×120(H)×37(D)mm *Not including antenna* |
| Weight | About 252G (including antenna and battery) |
| Parameter | Value |
|---|---|
| Receiver Sensitivity | ≤0.25uV (12dB SINAD) |
| Audio Power | 1W@10% |
| Audio Distortion | <10% |
| Signal-to-Noise | ≥45dB |
| Adjacent Channel Selectivity (Wide/Narrow) | ≥65 dB /≥60 dB |
| Intermodulation (Wide/Narrow) | ≥65 dB /≥60 dB |
| Receiver Current | ≤380mA |
User Tips
- Local Regulations: Always check and follow local radio communication regulations before operating the BAOFENG UV-36, especially concerning transmit frequencies and power levels.
- Shortwave Listening: The UV-36 supports shortwave receive (2.3-26.1 MHz), AM Air Band, and NOAA Weather Receive. These functions are receive-only.
- Bluetooth Programming: Utilize the Bluetooth programming feature for easier channel management and customization, which can be more convenient than manual programming for complex setups.
- Type-C Charging: Take advantage of the Type-C charging port for convenient and quick battery charging.
- Battery Care: For optimal battery life, ensure the first charge is at least 6 hours and avoid overcharging.
Warranty and Support
Warranty Certificate
A warranty certificate is typically included with your product. Please ensure it is legibly and clearly filled out, and present the seal and name of the dealer along with proof of purchase for warranty validation.
For a detailed warranty certificate template, please refer to the original user manual PDF: BAOFENG UV-36 User Manual (PDF)
Technical Support
If you encounter any problems that cannot be resolved using the troubleshooting guide, or if you require further assistance, please contact your local distributor for technical support.