Nordivale G30014GR13-LH

Contents

Nordivale 12x12FT Outdoor Gazebo Hardtop Instruction Manual

Model: G30014GR13-LH

Brand: Nordivale

1. Introduction

This manual provides detailed instructions for the assembly, operation, and maintenance of your Nordivale 12x12FT Outdoor Gazebo Hardtop. This gazebo is designed to enhance your outdoor living space with its durable construction and thoughtful features.

Key features include a double-layer galvanized steel roof with a gutter drainage system, a sturdy aluminum frame, and detachable curtains and netting for versatile use.

Video: Family enjoying the Nordivale Gazebo in various settings.

Nordivale 12x12FT Outdoor Gazebo with seating area
The Nordivale 12x12FT Outdoor Gazebo, providing a comfortable outdoor living space.

2. Safety Warnings and Precautions

⚠️ WARNING: This product can expose you to Carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

  • Assembly: Two or more people are required for assembly. A ladder and electric drill may be necessary.
  • Weather Conditions: Do not erect the structure in heavy winds or inclement weather. In windy weather, tighten the fence and netting to avoid tearing. Use a rope to pull the four corners of the gazebo to keep it stable in extreme weather. Do not stand under the gazebo in case of heavy snowfall; clear snow off the roof promptly.
  • Fire Safety: Do not use candles, matches, or any open flames near the tent. Do not use or store next to a pole with an open flame or flammable chemicals.
  • Screw Tightening: To better align the screws for practical situations, do not fully tighten screws initially. Keep all screws loose during the assembly process and tighten them after completing the installation. Repeat to confirm all screws, buckles, and straps are tightened every 90 days.
  • Handling Parts: Please note that some parts have sharp edges and should be handled with gloves.
  • Damage: If any parts are missing, broken, damaged, or worn, discontinue use of the product until repairs are made or factory replacement parts are installed.
  • Installation: Installation of the product in a manner that does not conform to the manufacturer's instructions may result in the loss of the warranty policy for this product. Consult your local authorities to check if permits are required to erect the shed.
  • Grounding: When installing on grass or dirt, the gazebo MUST be secured with ground pegs and wind ropes to ensure stability. Expansion screws are essential for stability on cement surfaces, and ground nails are for grassy surfaces. All are included in the accessories package.

3. Package Contents

Before beginning assembly, please verify that all parts listed below are present and undamaged. If any parts are missing or damaged, please contact customer support.

3.1. Tools Required (Not included in boxes)

  • Level
  • Rubber Mallet
  • Phillips Screwdriver
  • Drill
  • Allen Key
  • Safety Hat
  • Gloves
  • Safety Goggles
  • Stepladder (6.5Ft Or More)

3.2. Hardware List

Item No. Description Quantity
1M6x16mm Screw152
3M6x25mm Screw117
4ST4.8x12mm Screw24
5M6x10mm Screw8
8M6x15mm Screw16
910x50mm Expansion Screw12
10M5x12mm Screw44
12Wrench1
13Allen Key1
14Ground Nail12
15U-Bolt1
16M6x135mm Screw24

Note: Extra parts (1, 3, 4, 8, 10, U, Y, Y1) are provided in a bag labeled "Additional Parts".

3.3. Parts List

Item No. Description Quantity
AMain Post4
BTop Frame Beam4
B1Top Frame Beam (with holes)4
DRoof Connector4
E1Roof Support Beam4
E2Roof Support Beam4
EaUpper Roof Frame Beam4
EbUpper Roof Frame Beam4
EcUpper Roof Frame Beam4
F1Lower Roof Frame Beam4
F2Lower Roof Frame Beam4
G1Roof Panel Connector4
G3Roof Panel Connector4
G5Roof Panel Connector4
G6Roof Panel Connector4
HCorner Brace4
H1Corner Brace4
JBase Plate4
KPost Connector4
K1Post Connector4
LCentral Roof Cap Base1
MCentral Roof Cap1
NNut12
N1Nut4
PBeam Connector Plate4
SRoof Panel4
SaRoof Panel4
TCurtain (4PCS)1
T1Netting (4PCS)1
USliding Hook112
VHook Holder4
V1Roof Vent Panel2
V2Roof Vent Panel2
WRoof Support Bracket4
W1Roof Support Bracket4
W2Roof Support Bracket4
YRoof Panel Clip116
Y1Roof Panel Clip12
ZRoof Panel Edge72
Z1Roof Panel Edge16
Q1-Q8Roof Panels4 each
21Post Connector8
22Post Connector8

4. Setup and Assembly Instructions

Follow these steps carefully for proper assembly. Refer to the part numbers from the 'Package Contents' section.

4.1. Part 3: Main Frame Assembly

  1. Step 1: Assemble Posts (Refer to OCR Page 15)

    Attach base plates (J) and connectors (21, 22) to the main posts (A) using screws (1, 10). Ensure the single hole part of '22' faces inwards. Repeat for all four posts.

    Assembly Step 1: Attaching base plates and connectors to posts
    Assembly Step 1: Attaching base plates and connectors to posts.
  2. Step 2: Connect Top Frame Beams (Refer to OCR Page 16)

    Connect beam B1 to connector plate P using screws (1). Ensure the three holes on part P are facing upwards. Do not install P upside down.

    Assembly Step 2: Connecting B1 to P
    Assembly Step 2: Connecting B1 to P.
  3. Step 3: Join Top Frame Beams (Refer to OCR Page 17)

    Connect beam B to the assembled B1/P section using screws (1).

  4. Step 4: Attach Top Frame to Posts (Refer to OCR Page 18)

    Attach the assembled B/B1 sections to the top of the posts using screws (1, 8).

  5. Step 5: Complete Top Frame (Refer to OCR Page 19)

    Continue attaching the remaining B/B1 sections to form the complete top frame, securing with screws (1, 8).

  6. Step 6: Install Corner Braces (Refer to OCR Page 20)

    Attach corner braces (H and H1) to the top frame using screws (1).

  7. Step 7: Install Post Connectors (Refer to OCR Page 21)

    Attach post connectors (K and K1) to the top frame using screws (4).

  8. Step 8: Install Sliding Hooks (Refer to OCR Page 22)

    Slide all 112 sliding hooks (U) onto each rail of parts B and B1. Attach hook holders (V) using screws (10).

4.2. Part 4: Roof Frame Assembly

  1. Step 9: Assemble Upper Roof Frame Beams (Refer to OCR Page 24)

    Assemble the upper roof frame beams (Ea, Eb, Ec) using screws (1, 16, 17, 18).

  2. Step 10: Assemble Central Roof Cap Base (Refer to OCR Page 25)

    Assemble the central roof cap base (L) with the U-bolt (15).

  3. Step 11: Attach Upper Roof Frame Beams (Refer to OCR Page 26)

    Attach the assembled Ea/Eb sections to the central post using screws (1).

  4. Step 12: Secure Ea Sections (Refer to OCR Page 27)

    Secure the Ea sections to the main frame using screws (1).

  5. Step 13: Assemble Roof Support Beams (Refer to OCR Page 28)

    Assemble roof support beams (D, W2, E1, E2) using screws (10, 16, 19).

  6. Step 14: Attach Roof Panel Clips (Refer to OCR Page 29)

    Attach roof panel clips (Y and Y1) to the E1/E2 sections.

  7. Step 15: Attach E1/E2 Sections (Refer to OCR Page 30)

    Attach the assembled E1/E2 sections to the roof frame using screws (1).

4.3. Part 5: Roof Panel Installation

  1. Step 16: Attach Roof Panel Edges (Refer to OCR Page 32)

    Attach roof panel edges (Z and Z1) to the roof panels (Q1-Q8, S, Sa) by lightly tapping with a screwdriver.

  2. Step 17: Attach Roof Panel Connectors (Refer to OCR Page 33)

    Attach roof panel connectors (G1) to the S/Sa sections using screws (1).

  3. Step 18: Attach G1 to Roof Structure (Refer to OCR Page 34)

    Attach G1 to the roof structure using screws (1, N). Do not fully tighten the screws at this step to facilitate later installation.

  4. Step 19: Attach Central Roof Cap (Refer to OCR Page 35)

    Attach the central roof cap (M) to the top of the roof using screws (3, L).

  5. Step 20: Assemble Lower Roof Frame Beams (Refer to OCR Page 36)

    Assemble the lower roof frame beams (F1 and F2) with roof panel clips (Y) and roof support brackets (W1).

  6. Step 21: Attach F1/F2 Sections (Refer to OCR Page 37)

    Attach the assembled F1/F2 sections to the roof structure using screws (1, W).

  7. Step 22: Install Roof Panels (Refer to OCR Page 38)

    Install the roof panels (Q1-Q8). Steps 22, 23, and 24 need to be synchronized.

  8. Step 23: Align Roof Panel Clips (Refer to OCR Page 39)

    Ensure the roof panel clips (Y) are aligned with the holes in beams B/B1.

  9. Step 24: Secure Roof Panels (Refer to OCR Page 40)

    Secure the roof panels with screws (3).

  10. Step 25: Attach G5 and G6 (Refer to OCR Page 41)

    Attach roof panel connectors (G5 and G6) using screws (1, N, N1).

  11. Step 26: Attach G3 (Refer to OCR Page 42)

    Attach roof panel connectors (G3) using screws (1, N). Do not fully tighten at this stage.

  12. Step 27: Install Roof Vent Panels (Refer to OCR Page 43)

    First, remove screw (1) from G3. Then, attach roof vent panels (V1 and V2) using screws (5).

4.4. Part 6: Curtains and Netting Installation

  1. Step 28: Identify and Prepare Curtains (Refer to OCR Page 45)

    Identify the curtain parts (T) based on the number of holes and whether they hang on Part B or B1. Steps 28 and 29 need to be synchronized.

  2. Step 29: Attach Curtains (Refer to OCR Page 46)

    Attach the curtains (T-1, T-2, T-3, T-4) to the sidewall. Pay attention to the correct installation position for each curtain. Use the U hooks.

  3. Step 30: Identify and Prepare Netting (Refer to OCR Page 47)

    Identify the netting parts (T1) based on the number of holes and whether they hang on Part B or B1. Steps 30 and 31 need to be synchronized.

  4. Step 31: Attach Netting (Refer to OCR Page 48)

    Attach the netting (T1) to the sidewall. Hang the hooks attached to the netting on Part A.

  5. Step 32: Secure Gazebo to Ground (Refer to OCR Page 49)

    To improve wind resistance, ensure this step is completed. Use expansion screws (9) for cement surfaces and ground nails (14) for grassy surfaces. If not installed, strong winds may topple the gazebo.

5. Operating Instructions

5.1. Curtains and Netting

  • The gazebo features a double track design for the curtains and netting, allowing them to be opened or closed independently.
  • Use the Textilene netting to provide anti-mosquito protection while maintaining good ventilation.
  • The UV-blocking privacy curtains offer sun shade and privacy.
  • When not in use, the curtains and netting can be tied back to the posts using the extra Velcro straps for a cleaner appearance.

5.2. Gutter Drainage System

  • The integrated gutter system is designed to control rainwater runoff, minimizing splashing and directing water away from the gazebo's interior.
  • Ensure the gutters are clear of debris to maintain optimal drainage performance.
Detachable curtains and netting features
Features of the detachable curtains and netting, including Textilene netting, UV-blocking privacy, and double track design.
Built-in drainage system
Illustration of the built-in drainage system controlling rainwater runoff.

6. Maintenance

  • Regular Inspection: Repeat to confirm all screws, buckles, and straps are tightened every 90 days to ensure structural integrity.
  • Cleaning: Clean the galvanized steel roof and aluminum frame regularly with mild soap and water to prevent dirt buildup and maintain appearance. Avoid abrasive cleaners.
  • Snow Removal: In areas with heavy snowfall, clear snow off the roof promptly to prevent structural damage.
  • Curtains and Netting Care: The curtains and netting can be removed for cleaning. Follow fabric care instructions. Consider storing them during extreme weather conditions or off-season to prolong their lifespan.
  • Gutter Maintenance: Periodically check and clear the gutter drainage system of leaves, twigs, and other debris to ensure proper water flow.

7. Troubleshooting

  • Screws Not Aligning/Tightening: If a screw cannot be tightened, do not force it. Withdraw the screw, adjust the angle of the parts, and try to tighten it again. Ensure all screws are only hand-tightened initially and fully tightened after complete assembly.
  • Gazebo Instability: Ensure all screws are fully tightened. Verify that the gazebo is properly anchored to the ground using the provided expansion screws (for cement) or ground nails (for grass/dirt). In very windy conditions, consider using additional ropes to secure the four corners.
  • Water Pooling on Roof: Check the gutter drainage system for any blockages (leaves, debris) and clear them. Ensure the roof panels are correctly installed and aligned to allow for proper runoff.
  • Missing or Damaged Parts: If you discover any missing, broken, damaged, or worn parts during assembly or use, discontinue use immediately and contact customer support for replacements.

8. Specifications

Feature Detail
ModelG30014GR13-LH
Dimensions12 FT x 12 FT (Length x Width)
Height10.1 FT (Overall), 6.8 FT (Eave Height)
Covered Area144 sq. ft.
Frame MaterialPowder-Coated Aluminum
Roof MaterialDouble Layer Galvanized Steel Hardtop
Curtain MaterialUV-blocking fabric
Netting MaterialUpgraded Textilene Netting
FeaturesEasily Assembled, Waterproof, UV Protection, Excellent Ventilation, Thermal Insulation, Gutter Drainage System, Detachable Curtains and Netting
Package Weight118.6 kg
Number of Packages4
Product size diagram
Detailed product dimensions: 12FT x 12FT footprint, 10.1FT overall height, 6.8FT eave height.
All weather use features
The gazebo is designed for all-weather use, offering UV protection, waterproofing, and snow resistance.

9. User Tips

  • Regular Checks: Periodically check all connections and fasteners to ensure they remain tight, especially after strong winds or heavy rain.
  • Seasonal Preparation: Before winter, ensure the roof is clear of snow and ice. During summer, utilize the netting for insect protection and the curtains for shade and privacy.
  • Cleaning Routine: A quick rinse with a hose and a soft brush can keep the roof and frame looking new. For stubborn dirt, use a mild detergent.

10. Warranty and Support

We stand behind the quality of our furniture. Your Nordivale Gazebo comes with a one-year warranty from the date of purchase.

10.1. Return Policy

Items can be returned within 30 days of purchase. For a full refund, all items must be in brand-new/unused condition, with all accessories and parts firmly packed in original packaging. Please provide photos before and after packaging.

We will cover return shipping fees if:

  • Your item has a manufacturing defect in its materials or workmanship (e.g., torn wicker, misaligned screw holes).
  • Your item has been damaged in transit (e.g., broken glass, damaged wicker).
  • You received the wrong box(es) due to a warehouse error.
  • One or more boxes are lost in transit.

Customers will cover return shipping fees if:

  • You do not like the product(s) after receiving the box(es).
  • You no longer need the product(s) but have received the box(es).
  • You bought the product(s) by mistake but have received the box(es).
  • Order/Shipment cancellation failed and you have received the box(es).

Refunds are processed once the goods have been returned to our warehouse.

10.2. Contact Information

For any questions, concerns, or support, please reach out to us:

  • Email: service@kmcgloble-us.com
  • Phone: (+1) 213-816-4788

You can also refer to the original user manual PDF for additional details: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.