1. Important Safety Information
WARNING: Please read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture if it is an electrical product (this product is IP65 rated, but avoid submerging).
- Handle with care to avoid cuts or injuries.
WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.
2. Product Overview
The Intelamp Solar Flood Light is an outdoor lighting solution featuring a large solar panel, high brightness, motion sensing capabilities, and remote control. It is designed for various outdoor applications such as gardens, yards, paths, streets, and garages.
For a visual demonstration of the product's features, please watch the following video:
3. Setup and Installation
3.1 Unpacking and Preparation
- Carefully unpack all components: solar light fixture, solar panel, remote control, and mounting hardware.
- Remove all protective films from the solar light casing and solar panel.
- Ensure the solar panel is unobstructed and free of stains for optimal charging.
3.2 Mounting Location
Install or place the light fixture and solar panel in a well-lit, unobstructed location to maximize sunlight exposure. The recommended installation height for the light fixture is 1.8-2.5 meters (approximately 6-8 feet).
3.3 Connecting the Solar Panel
- Connect the solar panel to the light fixture using the provided 16.4ft cable.
- Ensure the connection is secure and waterproof.
4. Charging
The Intelamp Solar Flood Light is powered by a 12000mAh LifePO4 battery, charged by the external solar panel. No manual charging is required.
- Place the solar panel in direct sunlight. The panel will automatically absorb sunlight and convert it into electrical energy to charge the battery.
- A full charge typically takes 6-8 hours of sufficient direct sunlight.
- The flashing green light on the unit indicates that the light is charging.
- Note: The charging effect may weaken in cloudy or rainy weather, or during autumn and winter due to reduced sunlight intensity.
5. Operating Instructions
5.1 Power On/Off
- Locate the power switch on the side/bottom of the light fixture.
- Switch it to the "ON" position to turn on the light.
- Some models may support a light-controlled mode: switch to "Auto" for automatic turn-on after dark and turn-off at dawn.
5.2 Remote Control Functions
Use the provided remote control to select lighting modes and adjust settings.
- Power (ON/OFF): Turns the light on or off.
- Sensor Mode: Sets the duration for high brightness after motion detection (30s, 3min, 10min). The light dims or turns off when no one is detected.
- Lighting Mode: Automatically lights up for a set duration at night (2-12 hours). The light dims or turns off after the programmed lighting.
- Bright Adjustment: Adjusts the brightness level to 60%, 80%, or 100%.
5.3 Lighting Modes Explained
The light offers four distinct modes, selectable via the remote control:
- Mode 1 (Motion Sensor with Dim): The light stays at 20% brightness. When motion is detected, it brightens to 100% and returns to 20% after 30s/3min/10min (selectable) when the person leaves.
- Mode 2 (Motion Sensor Only): The light is off. When motion is detected, it turns on at 100% brightness and turns off after 30s/3min/10min (selectable) when the person leaves.
- Mode 3 (Constant Light with Dimming): In the dark or at night, the light turns on for 2-12 hours (selectable) at 80% brightness and then automatically switches to a reduced brightness (20%).
- Mode 4 (Constant Light then Off): In the dark or at night, the light turns on for 2-12 hours (selectable) at 80% brightness and then automatically turns off.
5.4 Linkable Function
The Intelamp Solar Flood Lights feature a unique linkable function, allowing multiple lights to communicate and illuminate together.
- Separate Motion Sensor Case: The included separate motion sensor case can detect motion within 26ft (8m) and signal linked lights within 100ft (30m) to illuminate in advance.
- Light-to-Light Linkage: If one light detects motion and brightens, it will signal other linked lights within 100ft (30m) to illuminate as well, creating a uniformly lit area.
6. Maintenance
- Cleaning: Regularly wipe the solar panel with a soft, damp cloth to remove dust, dirt, and debris. A clean panel ensures optimal sunlight absorption and charging efficiency.
- Inspection: Periodically check the light fixture, solar panel, and connecting cable for any signs of damage or wear. Ensure all connections are secure.
- Battery Care: While the battery is designed for long life, ensure the light receives adequate sunlight for charging, especially during shorter winter days, to maintain battery health.
- Storage: If storing the light for an extended period, ensure it is fully charged and stored in a dry place.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on at night. | Insufficient charging; switch is OFF; faulty sensor. | Ensure solar panel is in direct sunlight for 6-8 hours. Check if the power switch is ON. Clean the solar panel. Test sensor functionality. |
| Light duration is shorter than expected. | Insufficient charging; cloudy weather; low battery capacity. | Ensure maximum direct sunlight exposure. Consider weather conditions. If persistent, battery may be degrading (contact support). |
| Motion sensor not working. | Sensor obstructed; incorrect mode selected; sensor malfunction. | Clear any obstructions around the sensor. Ensure the correct motion sensor mode is selected via remote. |
| Remote control not responding. | Remote battery dead; remote out of range; interference. | Replace remote control batteries. Ensure remote is within effective range of the light. |
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | YL005-10EP-Black |
| Power Source | SOLAR |
| Battery Capacity | 12000mAh (LifePO4) |
| Light Brightness | 3000LM |
| Solar Panel Power | 10W, 5V/2000mA |
| Light Source | LED bulbs |
| Is Bulbs Included | Yes |
| Is Dimmable | Yes |
| Protection Level | IP65 (Waterproof) |
| Body Material | ABS |
| Installation Method | Self-contained |
| Solar Panel Cable Length | 16.4 ft |
| Certifications | CE, FCC, GS, LVD, ROHS, UL |
9. User Tips
- Optimal Placement: For best performance, ensure both the solar panel and the motion sensor have an unobstructed view of the sky and the area to be monitored, respectively.
- Remote Control Range: Keep the remote control within a reasonable distance of the light fixture for reliable operation.
- Winter Performance: During winter months or periods of prolonged cloudy weather, the light's performance (brightness and duration) may be reduced due to less sunlight for charging. Consider adjusting modes to conserve power if needed.
- Link Function Setup: When setting up multiple linked lights, ensure they are within the 100ft (30m) communication range for the link function to work effectively.
10. Manufacturer and Support Information
Manufacturer: Shenzhen Jindian Electronic Technology Co., Ltd.
Address: No. 9, Tianyang 1st Road, Datianyang Industrial Zone, Dongfang Community, Songgang Street, Bao'an District, Shenzhen City, Guangdong Province, China
Email: service@intelamp.com
EU Authorized Representative: SUCCESS COURIER SL
Address: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
Email: successservice2@hotmail.com
For further assistance or inquiries, please contact the manufacturer or authorized representative using the provided contact details.
A detailed user manual in PDF format is available for download: View User Manual (PDF)