HIROYASU HI-E380

Contents

HI-E380 Hiroyasu 10W Shortwave Walkie Talkie User Manual

Model: HI-E380 | Brand: HIROYASU

1. Introduction

The HI-E380 Hiroyasu is a new generation full-band two-way radio designed for ham enthusiasts. It offers a wide range of features including shortwave, MW, LW, CB, VHF, and UHF reception and transmission, aviation band reception, Bluetooth programming, and NOAA weather forecasts. This manual provides detailed instructions for setting up, operating, and maintaining your device to ensure optimal performance.

2. Getting Started

2.1. Package Contents

Before you begin, please check the contents of your package:

  • 1x HIROYASU HI-E380 Radio Body
  • 1x High gain FM/136-174/400-470MHz Antenna 21.5cm
  • 1x 2200mAh Li-tthium polymer Battery BT11
  • 1x Type-C charging Cable
  • 1x Belt clip
  • 1x English Manual
  • 1x Lanyard
  • 1x PC Programming Cable (Optional)
  • 1x Microphone Speaker (Optional)
  • 1x HIROYASU MH-31 CB Telescopic Antenna (Optional)
  • 2x Donut Antenna (SW Antenna and AM Antenna) (Optional)

2.2. Initial Setup

Watch this video for a visual guide on unboxing and initial assembly:

Video: Unboxing and initial assembly of the HI-E380 walkie-talkie.

  1. Battery Installation: Insert the 2200mAh Li-polymer battery pack into the back of the radio body, ensuring it clicks securely into place.
  2. Antenna Attachment: Screw the provided high-gain antenna onto the antenna connector at the top of the radio. Ensure it is finger-tight.
  3. Belt Clip and Lanyard: Attach the belt clip to the back of the radio if desired. Secure the lanyard to the designated loop for easy carrying.

2.3. Charging Instructions

The HI-E380 supports two charging methods:

  1. Dock Charging (Optional): Insert the battery pack or the radio with the battery pack into the charging dock. Ensure proper contact with the charging terminals of the dock.
  2. Type-C Charging: Connect the provided charging cable to the power adapter and plug the power adapter into an AC power outlet. Insert the charging cable into the Type-C interface of the main unit's battery.

When the device is charging, the red indicator light indicates charging in progress. The green indicator light indicates charging is complete.

3. Product Overview

3.1. Device Layout

Refer to the diagram below for an overview of the HI-E380's components:

Diagram of HI-E380 walkie-talkie with labeled parts: Antenna, Power Knob, Indicator Light, Display Screen, Microphone Jack, Headphone Jack, Analog PTT, PF2, PF3, Number Keypad, Type-C Charging Port.

Figure 1: HI-E380 Labeled Parts

3.2. LCD Display

The 1.77-inch 128*160 resolution full-color display provides clear information. Key elements include:

  • DH: Dual-band display indicator.
  • UFO: Indicates VFO (Variable Frequency Oscillator) mode.
  • ZONE1 H: Current zone and high power indicator.
  • 145.00000: Current frequency.
  • 435.65000: Secondary frequency.
  • Channel Name: Displays the current channel name (e.g., 006).
  • +60: Indicates frequency offset.
  • Dual-band Interface: Visual representation of dual-band operation.

3.3. Icon Descriptions

The LCD display uses various icons to convey device status and functions:

IconDescription
CTAnalog Sub-audio Tone Indicator: Current sub-audio tone is analog.
DCSDigital Sub-audio Tone Indicator: Current sub-audio tone is digital.
HHigh Power Indicator: Current transmission power is set to high.
MMedium Power Indicator: Current transmission power is set to medium.
LLow Power Indicator: Current transmission power is set to low.
NNarrowband Mode Indicator: Channel is operating in narrowband mode.
WWideband Mode Indicator: Channel is operating in wideband mode.
+Frequency Mode (+ Frequency Offset): Transmission frequency is reception frequency plus offset.
-Frequency Mode (- Frequency Offset): Transmission frequency is reception frequency minus offset.
RFrequency/Channel Mode Inverted Frequency: Reception and transmission frequencies are inverted.
TSimplex Mode: Reception and transmission frequencies are adjusted to be the same.
SCSC (Encryption) Indicator: Encryption function is enabled.
AMAM Modulation Indicator: Current frequency is in AM modulation mode.
SCRScrambler Function: Scrambler function is active.
VOXVOX (Voice-Operated Transmission): VOX function is enabled.
DWDual Standby: Dual-band standby function is set and active.
MMonitor Function Enabled: Monitor function is enabled.
STSide Tone Enabled: Side tone function is active.
KeyKeypad Lock: Appears when the keypad is locked.
RXSignal Strength: Indicates the strength of the received signal.
A/BA/B Band: Indicates whether the A band or B band is active.
VOLTransmit Audio Volume: Indicates the volume level of the transmitted audio.
BatteryBattery Status: Displays the remaining battery power.

4. Operating Instructions

4.1. Basic Operations

  • Main Frequency Band Selection: From the standby screen, short press the [A/B] key or long press the [EXIT] key to select the main frequency. The larger display indicates the currently active main frequency band.
  • PTT Function: When operating on the A band, press the PTT key to transmit on the A band frequency. When operating on the B band, press the PTT key to transmit on the B band frequency.
  • Channel Mode and Frequency Mode Switch: Short press the [VFO/MR] key or long press the [OK] key button to switch between channel mode and frequency mode.
  • AM Air Band Mode: Short press the [VFO/MR] key or long press the [OK] key to switch to frequency mode. Directly input the air band frequency within the range of 108 MHz to 136 MHz. The radio will automatically enter AM reception mode, and the channel status will display AM. This mode is primarily used to receive AM modulated signals.
  • Commercial FM Radio Broadcast Reception: Long press the button 0 to turn on the FM RADIO. Use the UP/DOWN keys or the channel knob to adjust the frequency, or input a frequency directly via the keypad.

4.2. Advanced Features

  • Scanning Mode: Assign the scanning function to the side keys PF2/PF3, or long press button 1 to start frequency or channel scanning. You can choose from Time Operation Mode (TO), Carrier Operation Mode (CO), or Search Operation Mode (SE).
  • Frequency Sweep / Copy Function: Define PF2/PF3 buttons as SEARCH from Menu 24-26. Press the button until the LCD displays "SEARCH/SEEK...". Press OK to select the frequency band. After capturing a frequency, it will continue to seek sub-tone CTCSS/DCS.
  • Weather Forecast NOAA Function: Define a PF button as NOAA from Menu 24-26. Press the designated side key to activate this function. The radio has 10 built-in fixed frequencies. Note: This function is available only in countries and regions that support NOAA channels.
  • DTMF Encode Sending: Press and hold the PTT button while entering number keys 0-9, MENU, UP, DOWN, EXIT, *, and #. Release the button to stop sending codes.
  • PTT-ID Function: Transmit identity codes or call codes via DTMF. There are 15 sets of call codes, configurable through Programming Software.
  • Shortwave Interface: After setting the PF3 side key as the shortcut to enter shortwave, press PF3 briefly to access the shortwave interface. Press and hold [0] to enter the shortwave interface. Briefly press [MENU] to switch STEP/BW/LAN/BFO.
  • Bluetooth Mobile Phone Programming: The device supports Bluetooth programming via a mobile app. Scan the QR codes below to download the app for iOS or Android.
QR codes for iOS and Android app downloads for Bluetooth programming.

Figure 2: Bluetooth Programming App QR Codes

4.3. Menu Function List (Summary)

The HI-E380 features an extensive menu system for customization. Here's a summary of key menu items:

No.MenuSetting
0SQLAdjust squelch level (0-9). 0 opens squelch, higher numbers increase sensitivity.
1STEPSelect frequency step (2.5K, 5.0K, 6.25K, 8.33K, 10.0K, 12.50K, 20.0K, 25.0K, 50.0K).
2TXPSet transmit power (High, Middle, Low).
3SAVEPower save mode (OFF, Normal Mode, Super Mode, Deep Mode).
4VOXVoice Transmit function (OFF, 1-9 sensitivity levels).
5W/NWideband (25Khz) / Narrowband (12.5Khz) selection.
6ABRBacklight settings (ON, 5sec-3min auto-off).
7TDRDual frequency standby (OFF, ON).
8BEEP PROMPTKeypad beep sound (OFF, ON).
9TOTTime out timer for transmit (15S-75S).
10ZONEOperation to change ZONE (ZONE 1-15).
11MEMCHCreate new channels (CH-001-064).
12DELCHDelete a stored channel (CH-001-064).
13R-CTCSSReceive Standard CTCSS (OFF, 67.0HZ-254.1HZ).
14R-DCSReceive Standard DCS (D023N-D7541).
15T-CTCSSTransmit Standard CTCSS (67.0Hz-254.1Hz).
16T-DCSTransmit Standard DCS (D023N-D7541).
17VOICEPRISubtone encryption (OFF, Encryption 1, 2, 3).
18CH-NAMEInput channel name.
19ROGEREnd-of-transmission tone (BEEP, TONE1200).
20VOICEVoice prompts (OFF, ON, ENGLISH, русский).
21LANGUAGEVoice guide language (ENGLISH, русский).
22BCLBusy channel lockout (OFF, ON).
23SC-REVScanning mode (TO, CO, SE).
24PF2Assign function to PF2 short press (SPECTRUM, RADIO, TX POWER, SCAN, SEARCH, NOAA, PTTB).
25PF2 LONG PRESSAssign function to PF2 long press (RADIO, TX POWER, SCAN, SEARCH, NOAA, SOS, SPECTRUM).
26PF3Assign function to PF3 short press (RADIO, TX POWER, SCAN, SEARCH, NOAA, SOS, SPECTRUM).
27OFFSETFrequency difference between radio transmission and reception (0-99.99750MHz).
28SFT-DTX frequency equals RX frequency plus/minus offset (+/-).
29POWER ON MSGPower on message (OFF, ON MSG, LOGO).
30S-CODEDTMF Signal codes (1-15).
31DTMF CODEDTMF transmission method (OFF, BOT, EOT, BOTH).
32DTMFSTDTMF auto sending code (OFF, ANI-ST, DT+ANI).
33AUTOLOCKAuto keypad lock time (OFF, 5S, 10S, 15S).
34SCAN ADDAdd or delete channels from scan list (ADD/Delete).
35TONEBurst tone (1000Hz, 1450Hz, 1750Hz, 2100Hz).
36PTT-LTDelay time before automatic DTMF transmitting (0-1000Ms).
37TIMEDelay time for exiting due to no operation (5-60sec).
38VOX DELAYVOX delay time (0.5sec-2.0sec).
39RP-STEEliminate squelch tail noise (OFF, 100ms-1000ms).
40RPT-RLDelay the tail tone of repeater (1-10s).
41MDF-AA BAND display mode (NAME, FREQ, CH).
42MDF-BB BAND display mode (NAME, FREQ, CH).
43TX-A/BPTT transmit band in dual standby (OFF, A, B).
44STESquelch tail noise eliminate (OFF, ON).
45AL-MODAlarm mode (ON SITE, SEND SOUND, SEND CODE).
46SCRAMBLEVoice scrambler function (OFF/ON).
47NOISE REDUCTIONNoise Reduction/Cancellation (OFF/ON).
48BLUETOOTHBluetooth connection (OFF/ON).
49RESETMenu initialization (VFO, ALL).
50ModulationAM/FM modulation selection.
51VERSIONShow firmware/hardware version number.

5. Specifications

AttributeValue
Brand NameHIROYASU
Model NumberHI-E380
Output Power(w)5w-10w
Battery Capacity(mAh)2200
Waterproof / Water-ResistantNo
Battery IncludedYes
MaterialPlastic
Storage Channel960
Frequency Range108-136mhz, 144-148MHz, 156-163MHz, 2.3-30Mhz, 220 - 260 MHz, 27Mhz, 300-390MHz, 400-520MHz, 430 - 440 MHz, 446MHz, 462-467MHz, 470-600MHz, 520-1710Khz, 65-108mhz, 400-470mhz, 136 - 174 MHz
Dimensions330*45*56mm (Antenna included)
Walkie Talkie TypePortable
Is_DisplayYes
Maximum Range5km-10km
OriginMainland China
CertificationRoHS, CE, FCC

6. Maintenance

To ensure optimal performance and extend the lifespan of this product, please follow the guidelines below for daily maintenance and cleaning.

6.1. Daily Maintenance

  • Do not pierce or scratch the product with hard objects.
  • Do not store the product in environments containing chemical corrosive substances.
  • Do not carry or use the product by pulling the earphone cable.
  • When not using the earphone jack, cover the interface with the protective cap.

6.2. Cleaning Procedure

Before cleaning, please power off the device and remove the battery:

  1. Regularly use a dry, clean, lint-free cloth or a soft brush to remove dust from the product surface and charging terminals.
  2. If the buttons or casing become dirty, use a neutral detergent and a non-woven cloth for cleaning. Do not use detergents, alcohol, sprays, or petroleum-based chemicals as they may damage the surface casing.
  3. After cleaning, ensure the product is completely dry before use.

7. Troubleshooting

If you encounter any issues with your HI-E380 walkie-talkie, please refer to the detailed user manual (PDF) for troubleshooting steps. Many common problems can be resolved by checking the menu settings or performing a factory reset (Menu 49: RESET).

For further assistance, please consult the full user manual available at: HI-E380 User Manual (PDF).

8. Warranty and Support

8.1. Warranty Terms

The main unit is covered for 12 months, and the battery and charging accessories are covered for 6 months from the date of sale. The warranty does not cover:

  • Failure to present the warranty card and purchase invoice.
  • Alteration of the warranty card or mismatch with the product.
  • Defects or damages caused by using this product under non-standard conditions.
  • Defects or damages caused by misuse, accidents, water ingress, or negligence.
  • Defects or damages resulting from improper testing, operation, repair, installation, modification, or adjustment.
  • Defects or damages caused by unauthorized repairs or disassembly.
  • Defects or damages caused by force majeure.
  • Normal wear and tear from regular use.

8.2. Product Warranty Card

Please ensure your Product Warranty Card is stamped and filled out completely by an authorized dealer to be valid. Keep it safe as it serves as an important proof for warranty services.

8.3. Additional Support

For any further questions or support, please refer to the comprehensive user manual (PDF) or contact your retailer.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.