FOTRIC TD2e

Contents

FOTRIC TD2e Acoustic Imager User Manual

Model: TD2e | Brand: FOTRIC

1. Introduction

The FOTRIC TD2e Acoustic Imager is an advanced ultrasonic camera designed to visualize sound and quickly locate issues in various environments. Utilizing 64 MEMS digital microphones and sophisticated sound processing, it pinpoints targets and filters out noise with superior accuracy. This manual provides essential information for the safe and effective use of your TD2e Acoustic Imager.

FOTRIC TD2e Acoustic Imager showing applications in industrial, HVAC, electrical inspection, and leak detection.
Figure 1: FOTRIC TD2e Acoustic Imager and its primary applications.

The TD2e is ideal for industrial inspection, HVAC inspection, electrical inspection, and leak detection, offering a working distance of 0.3 to 60 meters and detecting frequencies from 2 kHz to 100 kHz.

2. Setup and First Use

2.1 Unboxing and Package Contents

Upon receiving your FOTRIC TD2e Acoustic Imager, carefully unbox the package and verify all contents against the list below. The complete kit includes:

  • FOTRIC TD2e Acoustic Imaging Camera
  • Two (2) Rechargeable Lithium Batteries (3.6V, 5000mAh)
  • Charging Dock
  • Power Adapter
  • USB Type-C to USB Cable (compliant with USB 3.0/2.0 standard)
  • 32 GB TF Card
  • Tool Holder
  • Quick Start Guide
  • Packing List
  • Soft Bag
  • Hard Carrying Case
Contents of the FOTRIC TD2e complete kit, including the camera, batteries, charger, cables, and carrying case.
Figure 2: FOTRIC TD2e Complete Kit contents.

2.2 Battery Installation and Charging

  1. Ensure the device is powered off before installing or removing batteries.
  2. Insert a fully charged 3.6V, 5000mAh rechargeable lithium battery into the battery compartment at the base of the handle. The battery is field-replaceable.
  3. To charge the battery, place it in the charging dock and connect the power adapter. The charging indicator will show the charging status.
  4. A fully charged battery provides at least 3 hours of operation (depending on usage).

2.3 Powering On/Off

  • To power on: Press and hold the power button (usually located on the front panel below the screen) until the display illuminates.
  • To power off: Press and hold the power button until a shutdown prompt appears, then confirm.

3. Operating Instructions

3.1 Understanding Acoustic Imaging

The FOTRIC TD2e converts sound waves into a visible representation, allowing you to "see" sound sources. This is achieved through a process involving:

  1. Sound Wave Signals: The device captures sound waves from multiple directions.
  2. Microphone Array: A 64 MEMS digital microphone array collects these signals.
  3. FPGA Beamforming Algorithm: A Field-Programmable Gate Array (FPGA) processes the signals using a beamforming algorithm to calculate the sound source direction.
  4. Embedded Interactive Platform: The processed data is then rendered on the device's display.
  5. Acoustic Image Generation: A visible hotspot is overlaid on the live image, indicating the precise location of the sound source.
Diagram illustrating how acoustic imaging works, from sound wave signals to acoustic image generation.
Figure 3: How Acoustic Imaging Works.

3.2 Frequency Range and Detection

The TD2e detects sound within a wide frequency range of 2 kHz to 100 kHz, covering ultrasonic frequencies beyond human hearing. This allows for the detection of various air and gas leaks, as well as mechanical issues that produce high-frequency sounds.

Diagram showing the acoustic camera detection range from 2kHz to 100kHz, encompassing audible sound and ultrasound.
Figure 4: Acoustic Camera Detection Range.

You can manually adjust the frequency range and display the peak frequency on the screen to narrow the band, reduce unrelated noise, and focus on the signal of interest.

3.3 Sound Source Modes

The TD2e offers multiple sound source modes to suit different inspection scenarios:

  • Single-source Mode: Focuses on a single dominant hotspot.
  • Multi-source Mode: Displays multiple sound sources simultaneously.
  • All-source Mode: Provides a comprehensive view of all detected sound sources.

Additionally, the device includes two detection modes:

  • Micro-Detection Mode: Designed to bring faint sound sources into view.
  • Noise Suppression Mode: Filters out low-level sounds to reduce environmental interference and improve clarity.
Video 1: Demonstration of FOTRIC TD2e features, including sound processing, beamforming, low-latency rendering, wide field of view, frequency detection, lightweight design, swappable battery, and various sound source modes.

3.4 Common Applications

The FOTRIC TD2e is a versatile tool for various inspection tasks:

  • Air Leak Detection: Quickly identify leaks in compressed air lines, vacuum systems, valves, and actuators.
  • Partial Discharge Detection: Locate electrical partial discharges in high-voltage equipment.
  • Mechanical Fault Diagnosis: Detect abnormal equipment noise in pumps, motors, and other machinery.
  • Industrial Maintenance: General maintenance and troubleshooting in industrial settings.
  • Automotive Inspection: Identify leaks or abnormal noises in vehicles.
  • HVAC Inspection: Locate leaks or issues in heating, ventilation, and air conditioning systems.
Images showing the FOTRIC TD2e in use for inspecting compressed air lines, vacuum systems, valves, actuators, and pumps/motors, with sound hotspots visible.
Figure 5: Real-world applications of the TD2e Acoustic Imager.

4. Maintenance and Care

  • Cleaning: Use a soft, dry cloth to clean the device's exterior. For the display screen, use a screen-specific cleaning solution and a microfiber cloth. Avoid abrasive cleaners or solvents.
  • Storage: Store the device in its hard carrying case in a cool, dry place when not in use.
  • Battery Care: To prolong battery life, avoid fully discharging the battery frequently. If storing for extended periods, charge the battery to approximately 50% and store it separately from the device.
  • Environmental Protection: The device has an IP54 waterproof level and is designed for 2-meter drop resistance, but it should still be handled with care and protected from extreme conditions.

5. Troubleshooting

This section addresses common issues you might encounter with your FOTRIC TD2e Acoustic Imager. For more complex problems, please contact customer support.

ProblemPossible CauseSolution
Device does not power on.Battery is depleted or not properly installed.Ensure battery is fully charged and correctly inserted. Try a different charged battery if available.
No acoustic image/hotspot visible.Sound source is too weak, too far, or outside the frequency range.Move closer to the suspected source. Adjust the frequency range. Check if the sound source is within the 2kHz-100kHz range. Try Micro-Detection Mode.
Excessive background noise.Environmental noise interference.Activate Noise Suppression Mode. Adjust the frequency band to filter out irrelevant sounds.
Display is unresponsive.Software glitch or temporary freeze.Perform a soft reset by holding the power button until the device restarts. If the issue persists, contact support.

6. Technical Specifications

Below are the detailed technical specifications for the FOTRIC TD2e Acoustic Imager:

ParameterSpecification
Brand NameFOTRIC
Model NumberTD2e
CertificationFCC
OriginMainland China
Microphone Channels64 MEMS Digital Microphones
Acoustic Image Field of View (FOV)58° * 45°
Sound Pressure Sensitivity0.01 L/min @ 0.1 MPa, 1.5 m, φ30 μm orifice
0.025 L/min @ 0.3 MPa, 3.5 m, φ30 μm orifice
0.045 L/min @ 0.3 MPa, 4.5 m, φ40 μm orifice
Sound Sampling Rate200 kHz
Image ModeSingle-source, Multi-source, All-source
Working Distance0.3 ~ 60 m
Positioning Frequency Range2 kHz - 100 kHz
Frequency Range SelectionSupports manual adjustment of frequency range; Supports displaying peak frequency
Noise Reduction ModeFilters out low-level sounds to reduce environmental interference
Micro Detection ModeCaptures faint sounds to avoid missing potential issues
Display Screen3.5-inch, 640 * 480 pixels, IPS LCD touchscreen with explosion-proof cover glass
Digital Camera5MP industrial-grade digital camera
Image FormatJPG (acoustic image)
USB InterfaceUSB Type-C, compliant with USB 3.0/2.0 standard
LED Illumination LampSupport flashlight illumination and flash mode
Battery Type3.6V, 5000mAh Rechargeable Lithium Battery, Field-Replaceable
Battery Operating Time≥ 3 hours per battery (depends on usage)
Protection RatingIP54 (GB/T 4208 / IEC 60529)
Drop ResistanceDesigned for 2-meter drop resistance
Shock Resistance25 g (GB/T 2423.5 / IEC 60068-2-27)
Vibration Resistance2 g (GB/T 2423.10 / IEC 60068-2-6)
Supported LanguagesEnglish, German, French, Spanish, Portuguese, Italian, Polish, Japanese, Korean, Traditional Chinese, Thai

7. User Tips

  • For optimal leak detection, operate the device in a quiet environment to minimize background noise interference.
  • When inspecting large areas, start with a wider field of view and then narrow down the focus as potential sound sources are identified.
  • Regularly check the battery level, especially before critical inspections, to ensure uninterrupted operation.
  • Utilize the professional analysis software (PC software) for detailed data analysis, reporting, and trend tracking of your inspection results.

8. Warranty and Support

8.1 Warranty Information

The FOTRIC TD2e Acoustic Imager comes with a 2-year warranty, ensuring coverage for manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.

8.2 Customer Support

For any technical assistance, troubleshooting not covered in this manual, or warranty inquiries, please contact FOTRIC customer support. Support is typically available with replies within 24 hours.

You can find contact information on the official FOTRIC website or through your purchase platform.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.