iScooter iK7 Children Electric Scooter

1. Safety Instructions

This manual contains essential safety information. For your child's safety, it is important that you review this manual with your children and ensure they understand all warnings, cautions, and instructions. Children should always ride under adult supervision. We recommend regularly reviewing this manual and performing inspections and maintenance on the electric scooter to ensure safe riding.

WARNING

Riding is both a sport and a form of entertainment, but there may be dangers such as loss of control and falling while riding. Therefore, safety precautions should be taken before riding, and the safety requirements for riders in this manual must be strictly followed. We do not assume any direct or shared liability for property damage, personal injury, accidents, legal disputes, or any other adverse events arising from the misuse or violation of the recommended usage provided in this manual.

• This product is only suitable for children above 8 years old, not for adults.
• No passengers are allowed.
• A helmet and other protective equipment are required during riding.
• Do not ride it in unsafe or illegal places.
• Practice in an open area first and ride only after the rider has mastered the skills.
• Do not make dangerous movements or ride with one hand while riding.
• Avoid riding on steps, as this may cause the product to tip over, resulting in potential injury or damage.
• The maximum speed of this product is 12 mph (20 km/h).
• Avoid using this product in extreme temperatures.
• If uneven or poor road conditions are encountered, please ride slowly or get off.
• Do not ride this product on oily or icy surfaces.
• Do not immerse the product in water or spray water on the vehicle body directly.
• The maximum load is 176 lbs (80 kg). Do not exceed this limit.

ALWAYS INSPECT THE PRODUCT BEFORE RIDING

• Always inspect before riding and perform regular maintenance.
• Check and secure all fasteners before each ride.
• Replace worn or damaged parts immediately.
• Use caution when riding, as skill is required to avoid falls or collisions, which could result in injury to the rider or others.

Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

2. Package Contents

Please check the package contents carefully. If any items are missing or damaged, please contact customer service.

• (1) Scooter Body
• (2) Handlebar
• (3) Front Wheel + Axle
• (4) Front Fender
• (5) Saddle + Seatpost
• (6) Seat Tube
• (7) Basket
• (8) U-shaped Basket Mount
• (9) Toolkit (L-shaped hex wrench x3, Open-end wrench x3)
• (10) Charger
• (11) User Manual

3. Product Overview

Familiarize yourself with the different parts of your iScooter iK7 electric scooter.

• (1) Headlight
• (2) Thumb Throttle
• (3) Thumb Brake
• (4) Height Adjustment Clamp
• (5) Front Fender
• (6) Charging Port
• (7) Atmosphere Lights (Two Sides)
• (8) Saddle
• (9) Basket
• (10) Taillight & Brake Light
• (11) Rear Fender
• (12) Kickstand

4. Setup

4.1. Handlebar Installation

1. Connect the cable.
2. Press down the spring button on the steerer tube and slide the handlebar onto the steerer tube until the spring button fully pops out from the hole on the handlebar.
3. Tighten the two bolts of the clamp.

4.2. Front Fender Installation

1. Remove the bolt and washer from the fender mounting point.
2. Pass the bolt through the hole on the fender.
3. Tighten the bolt into the mounting point.

4.3. Front Wheel Installation

1. Remove one nut and two bushings from the axle.
2. Lift the front fork, position the front wheel between the fork legs, and pass the axle through the fork dropouts, washers, and wheel hub.
3. Tighten the nuts on two sides firmly.

4.4. Basket Installation

The basket can be installed on either the U-shaped mount or the seat tube, depending on how the scooter is assembled (stand-up mode or seated mode).

Stand-up Mode Basket Installation

1. Remove the bolts from the U-shaped basket mount (these bolts can also be used to secure the seat tube).
2. Connect the mount to the posts on the rear of the scooter.
3. Tighten the bolts firmly to secure the mount in place.

1. Remove the bolts and nuts from the basket.
2. Position the basket against the basket mount, align the holes.
3. Firmly tighten the bolts into the holes and then the nuts to secure the basket in place.

Seated Mode Basket Installation

1. Insert the seat post into the saddle clamp, then tighten the nuts on two sides.
2. Connect the seat tube to the posts on the rear of the scooter, and tighten the bolts (pre-installed on the U-shaped basket mount) firmly to secure the seat tube in place.

4.5. Handlebar Height Adjustment

1. Open the lever of the handlebar height adjustment clamp.
2. While pressing the spring button, adjust the handlebar height, ensuring the spring button pops out from one of the three spring button holes.
3. Fully close the clamp lever.

5. Operating Instructions

5.1. Controls Overview

• Power Button: Used for turning the scooter ON/OFF, switching riding modes, and changing speed units.
• Light Button: Controls the headlight, atmosphere lights, and taillight.
• Thumb Brake: Activates the electronic brake.
• Thumb Throttle: Controls acceleration.

5.2. Display Information

• (1) Battery Level
• (2) Real-time Speed / Error Code
• (3) Bluetooth Connected
• (4) Lights ON
• (5) Speed Unit
• (6) Riding Mode

5.3. Basic Functions

• Power ON/OFF Scooter: Press and hold the Power button. The scooter will automatically shut down after 5 minutes of inactivity.
• Switch Riding Mode: Double-press the Power button. The riding mode defaults to the first mode after each restart.
• Switch Speed Unit: Press the Power button three times to switch between Mph and km/h.
• Select Zero Start / Non-zero Start mode: Press the Power button four times.

  WARNING: Non-zero start is set at the factory. For safety, select the correct mode that best matches the rider's skill level!

  • Zero start mode: The motor engages immediately when you press the throttle, even from a complete stop.
  • Non-zero start mode: The scooter requires a small initial push before the throttle becomes active, preventing sudden acceleration from a standstill.
• Turn ON/OFF Lights: Press the Light button to turn on or off the headlight, atmosphere lights, and taillight simultaneously.

  TIP: The mode of the atmosphere lights can be adjusted via the scooter app.

5.4. Riding Techniques

Starting to Ride

1. Disengage the kickstand, turn on the scooter, and select your desired speed level.
2. Hold the handlebar, place one foot on the deck, and push off with the other to start moving.
3. As the scooter moves, place your other foot on the deck. Once balanced, press the throttle to accelerate.

Turning

1. While turning, lean slightly into the direction of the turn and gently turn the handlebar.

Braking

1. To slow down, release the throttle.
2. To come to a complete stop, press the thumb brake.

6. Charging

• Fully charge the battery before first use.
• When the battery is low, charge immediately.
• Only use the original charger to charge the battery.
• The electric scooter is fully charged when the charger indicator changes from red to green.
• Keep the charging port cover closed when not charging.
• The scooter cannot be operated while it is charging.

7. Maintenance

• Regularly inspect the scooter for any signs of wear or damage before each ride.
• Ensure all fasteners are tight and secure.
• Replace any worn or damaged parts immediately to maintain safety and performance.
• Keep the scooter clean and dry. Avoid immersing it in water or spraying water directly on the body.
• Store the scooter in a cool, dry place away from direct sunlight and extreme temperatures.

8. Troubleshooting

If you encounter any issues with your iScooter iK7, please refer to the following common troubleshooting steps:

• Scooter not turning on: Ensure the battery is charged. Press and hold the power button for at least 2 seconds.
• Scooter not accelerating: Check if the scooter is in 'Non-zero start' mode; if so, give it a small push to activate the throttle. Ensure the throttle is fully pressed.
• Lights not working: Press the light button to toggle the lights on/off. Check the scooter app for light mode settings.
• Bluetooth not connecting: Ensure Bluetooth is enabled on your phone and the scooter is powered on. Search for 'iK7' in your device's Bluetooth settings and attempt to pair.
• Unusual noises or vibrations: Stop riding immediately and inspect all components for loose parts, damage, or obstructions.

For further assistance, please refer to the digital manual available via the iScooter club app or contact customer support.

9. Specifications

10. User Tips

• For younger or less experienced riders, always start in 'Non-zero start' mode and the lowest speed setting (Eco Mode) until they gain confidence and control.
• Utilize the adjustable handlebar and removable seat to customize the scooter for comfort and riding style, whether standing or seated.
• Take advantage of the smart app control to set custom speed limits for added safety and to personalize the ambient light modes.
• Remember to wear a helmet and other protective gear at all times while riding.

11. iScooter Club App

Enhance your iScooter iK7 experience by downloading the official 'iScooter club' app.

With the app, you will get:

• Digital manual
• Step-by-step setup videos
• FAQs & troubleshooting
• Electronic lock

The app allows you to customize speed limits, adjust light modes, and check the vehicle's status.

12. Compliance and Legal Information

12.1. FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

12.2. CE Warning and Declaration of Conformity

This appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.

For the full text of the EU Declaration of Conformity, visit the link: https://www.iscooterglobal.de/pages/konformitatserklarung

12.3. Disposal of Electrical and Electronic Equipment

The crossed-out garbage can symbol means that you are legally obliged to dispose of these devices separately from unsorted municipal waste. Disposal via the residual waste bin or the yellow bin is prohibited. If the products contain batteries or rechargeable batteries that are not permanently installed, they must be removed before disposal and disposed of separately as a battery.

Owners of old devices can hand them over within the scope of the options for returning or collecting old devices that have been set up and made available by public waste disposal authorities, so that proper disposal of the old devices is ensured.

We would like to point out to all end users of waste electrical and electronic equipment that they are responsible for: deleting personal data on the old equipment itself to be disposed of.