Pro Chaser PC210653

Contents

Pro Chaser PC210653 Carburetor Kit Instruction Manual

Model: PC210653

For Briggs & Stratton 12211 Intek 190 Engine 850 Series 6.75 OHV and John Deere 020382 R

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the Pro Chaser PC210653 Carburetor Kit. This kit is designed as a replacement part for various small engines, including specific Briggs & Stratton and Intek models, and is compatible with certain John Deere and Coleman equipment. Please read all instructions carefully before proceeding with installation or use.

Important Safety Information

  • Disconnect Power: Always disconnect the vehicle's or equipment's power supply (e.g., battery terminal, spark plug wire) before installation or maintenance to prevent accidental starting or electrical short circuits.
  • Intended Use: This product is intended for use exclusively on original-equipment vehicles or machinery as specified. Modification or use for non-specified purposes is strictly prohibited and may void any warranties and create safety hazards.
  • Storage: This product is not intended for use in children's toys or infant products. Store out of reach of children and pets.
  • Professional Installation: If you are unsure about any part of the installation process, it is recommended to seek assistance from a qualified technician.

Package Contents

The Pro Chaser PC210653 Carburetor Kit includes the following components:

  • 1 x Carburetor
  • 2 x Choke Levers (choose the one that best suits your application)
  • 2 x Gaskets
  • 2 x Butterfly Valves
  • 2 x Screws
  • 1 x Sponge Ring
  • 2 x Air Filters
  • 1 x Fuel Hose
  • 2 x Clamps
  • 1 x Spark Plug
  • 1 x Fuel Filter
  • 1 x Fuel Shut Off Valve
Pro Chaser PC210653 Carburetor Kit Components
Image 1: All components included in the Pro Chaser PC210653 Carburetor Kit.

Setup and Installation

Before beginning installation, ensure the engine is cool and the power supply is disconnected as per the safety warnings.

General Installation Procedure:

  1. Verify Compatibility: Confirm that this carburetor kit is compatible with your specific engine model and application.
  2. Clean Mounting Location: Thoroughly clean the area where the carburetor will be mounted, removing any old gasket material, dirt, or debris.
  3. Align Interfaces: Carefully align the new carburetor with the engine's intake manifold and air filter housing.
  4. Secure Screws: Install and securely tighten the mounting screws, ensuring an airtight seal. Do not overtighten.
  5. Connect Fuel Lines: Attach the fuel hose, fuel filter, and fuel shut-off valve as required for your engine. Use the provided clamps to secure connections.
  6. Install Air Filter: Place the new air filter and sponge ring into the air filter housing.
  7. Install Spark Plug: Replace the old spark plug with the new one provided.

Choke Lever Installation:

The kit includes two different choke levers. Select the one that best fits your machine's design and functionality.

  1. Select Lever: Choose the choke lever that matches your machine's requirements.
  2. Insert Lever: Insert the selected choke lever vertically into the designated choke lever hole at the top of the carburetor.
  3. Secure Butterfly Valve: Use a suitable tool to gently push the butterfly valve into its correct position, ensuring it operates smoothly with the choke lever.
Carburetor Front Mounting Hole Distance
Image 2: Front view of the carburetor, showing the center-to-center mounting hole distance of 45.15mm / 1.77''.
Carburetor Back Mounting Hole Distance
Image 3: Back view of the carburetor, showing the center-to-center mounting hole distance of 32.65mm / 1.28''.
Carburetor Side View with Fuel Inlet
Image 4: Side view of the carburetor, illustrating the fuel inlet connection point.

Operating Instructions

After successful installation, ensure all connections are secure and there are no fuel leaks. Refer to your engine's specific user manual for starting procedures. The carburetor's primary function is to mix air and fuel in the correct ratio for combustion. Proper adjustment (if applicable to your model) is crucial for optimal engine performance.

  • Fuel Supply: Ensure the fuel shut-off valve is in the 'ON' position before attempting to start the engine.
  • Choke Operation: Use the choke lever as directed by your engine's manual for cold starts. The choke restricts airflow, enriching the fuel mixture to aid in starting.
  • Engine Warm-up: Allow the engine to warm up for a few minutes before operating at full throttle.

Maintenance

Regular maintenance of your carburetor and associated components will ensure long-lasting performance and efficient engine operation.

  • Air Filter Replacement: Regularly inspect and replace the air filter and sponge ring (provided in the kit) to ensure clean air intake. A dirty air filter can restrict airflow and cause the engine to run rich.
  • Fuel Filter Replacement: Periodically replace the fuel filter to prevent contaminants from reaching the carburetor, which can cause clogging and poor performance.
  • Carburetor Cleaning: If the engine experiences issues like rough idling, stalling, or difficulty starting, the carburetor may need cleaning. This typically involves disassembling the carburetor, cleaning jets and passages with carburetor cleaner, and replacing gaskets.
  • Spark Plug Inspection: Inspect the spark plug periodically for wear or fouling. Replace it with the new spark plug provided in the kit if necessary.

Troubleshooting

Here are some common issues and potential solutions related to carburetor performance:

Problem Possible Cause Solution
Engine won't start No fuel, clogged fuel filter, dirty spark plug, incorrect choke setting, clogged carburetor jet. Check fuel level, replace fuel filter, replace spark plug, adjust choke, clean carburetor.
Engine runs rough/stalls Dirty carburetor, old fuel, air leak, incorrect idle mixture. Clean carburetor, use fresh fuel, check for air leaks around gaskets, adjust idle (if adjustable).
Engine lacks power Dirty air filter, restricted fuel flow, incorrect fuel/air mixture. Replace air filter, check fuel lines and filter, clean carburetor.
Fuel leaks Loose connections, damaged gaskets, cracked fuel hose. Tighten clamps, replace gaskets, replace fuel hose.

Specifications

Carburetor Dimensions:

  • Front Mounting Hole Distance (Center to Center): 45.15mm / 1.77’’
  • Back Mounting Hole Distance (Center to Center): 32.65mm / 1.28’’

Compatibility:

This carburetor kit is compatible with the following models and applications:

  • Replaces Briggs & Stratton Part Numbers: 696981, 698860, 694508, 795069, 698859, 790180, 790290, 693865, 697354, 698474, 791991, 698810, 698857, 698478, 694174, 690046, 693751, 798650
  • Replaces Briggs & Stratton Engine Models: 110432-0179-E1, 110432-0198-E1, 110432-0213-E1; 120202, 120212, 120232, 120252, 120292, 121002, 121012, 121212, 121232, 120000, 121000
  • Replaces Intek Engine Applications:
    • Intek 206 5.5hp engine powered Craftsman tiller, garden tiller, old roto-tiller, Sears tiller, etc.
    • Intek 206 carburetor 6.5 HP Engine Power Washer
    • Intek 190 carburetor 5.5 HP pressure washer engine
    • Coleman Powermate 3200 generator

Package Dimensions & Weight:

  • Length: 30 cm
  • Width: 25 cm
  • Height: 10 cm
  • Weight: 0.65 kg

User Tips

  • Always use fresh, clean fuel. Stale fuel can cause carburetor issues.
  • When storing equipment for extended periods, drain the fuel system or use a fuel stabilizer to prevent gumming in the carburetor.
  • Ensure all gaskets are properly seated and undamaged during installation to prevent air leaks, which can affect engine performance.
  • Keep spare air and fuel filters on hand for routine maintenance.

Compliance Markings

This product has obtained CE Mark certification, complying with relevant EU regulatory requirements. It also complies with the EN ISO 9001:2015 Quality Management System standard and satisfies Regulation (EU) 2020/177.

EC REP: MJCM SARL France, 78 avenue des Champs Elysees Bureau 326 Paris Ile-de-France

Warranty and Support

For any questions regarding installation, troubleshooting, or product defects, please contact the seller or manufacturer directly. Please have your product model number (PC210653) and purchase information ready when contacting support.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.