LCTC LC-AV-2/3

Contents

LCTC Voltage Protector User Manual

Models: LC-AV-2, LC-AVP-3

Adjustable Over/Under Voltage and Overcurrent Protection Relay with Digital Display

1. Introduction

The LCTC Voltage Protector is a multi-function device designed to safeguard electrical equipment from damage caused by voltage fluctuations (overvoltage and undervoltage) and overcurrent conditions. It features a digital display for real-time monitoring of voltage, current, and (for model LC-AVP-3) accumulated energy consumption (kWh). This device is designed for easy installation on a DIN rail and offers adjustable protection parameters and automatic reclosing functionality.

LCTC Voltage Protector showing dual and triple display models with key features
LCTC Voltage/Current Protector models with key features highlighted.

2. Safety Information

WARNING: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel.

  • Ensure the power supply is completely disconnected before installation or wiring.
  • Verify all connections are secure and correct according to the wiring diagram.
  • Do not operate the device if it is damaged or malfunctioning.
  • This device is designed for low voltage applications (below 50Vac or 75Vdc) in the EU LVD Voltage standard.

3. Product Components and Display

The LCTC Voltage Protector features a clear digital display and intuitive control buttons:

Diagram of the LCTC Voltage Protector display and buttons
Real-Time Data Display and Button Functions.
  • Voltage Display (V): Shows the current line voltage.
  • Current Display (A): Shows the current load.
  • kWh Display (kWh): (LC-AVP-3 model only) Shows accumulated energy consumption.
  • SET Button: Enters parameter setting mode.
  • Digit "+" (Up Arrow): Increases parameter values or navigates menus.
  • Digit "-" (Down Arrow): Decreases parameter values or navigates menus.
  • ON/OFF Button: Manually switches the output on or off.
  • IN Terminals (N, L): Power input terminals.
  • OUT Terminals (N, L): Power output terminals to the load.

4. Specifications

Product dimensions and technical parameters table
Product Dimensions and Technical Parameters.
Technical Data
Parameter Value
Operating Voltage AC80-300V
Rated Supply Voltage AC80-300V
Rated Frequency 50-60Hz (or 35/75Hz)
Overvoltage Range (>V) AC130-300V
Undervoltage Range (<V) AC80-210V
Current Range 1-40A / 1-63A (depending on model)
Max Rated Current 40A / 63A (depending on model)
Power-off Delay Range 1-60S
Power Failure Recovery Time Range 1-60S
Voltage Correction Value -99-99V
Current Correction Value -9.9-9.9A
Overcurrent Power Failure Delay Range 1-30S
Working Indicator Green (Normal), Red (Fault)
Certification CE

Note: There may be a measurement error of 1-3mm in physical dimensions.

5. Installation and Wiring

The LCTC Voltage Protector is designed for DIN rail mounting.

5.1 Mounting

Snap the device onto a standard 35mm DIN rail in your electrical panel. Ensure it is securely fastened.

LCTC Voltage Protector mounted on a DIN rail
Device mounted on a DIN rail.

5.2 Wiring Diagram

Connect the device according to the following diagram. Ensure proper polarity (Neutral 'N' and Live 'L') for both input and output terminals.

Wiring diagram for LCTC Voltage Protector with circuit breaker and load
Typical wiring for the LCTC Voltage Protector with an upstream circuit breaker and a load.
  1. Connect the incoming Neutral (N) and Live (L) wires from your power source to the 'IN' terminals of the protector.
  2. Connect the outgoing Neutral (N) and Live (L) wires from the 'OUT' terminals of the protector to your load (e.g., light bulb, appliance).
  3. It is recommended to install an appropriate circuit breaker upstream of the voltage protector for additional safety and circuit protection.

6. Operating Instructions

6.1 Power On and Display

Once wired correctly and power is supplied, the device will power on and display real-time voltage and current. If you have the LC-AVP-3 model, it will also display accumulated kWh.

6.2 Setting Protection Parameters

The device offers adjustable parameters for overvoltage, undervoltage, overcurrent, and trip/recovery times. The video below demonstrates some of these functions.

Demonstration of manual switch, protection functions, and manual resume.
  1. Enter Setting Mode: Press and hold the "SET" button for a few seconds until the display changes to parameter setting mode.
  2. Navigate Parameters: Use the "+" (Up) and "-" (Down) buttons to cycle through different parameters (e.g., overvoltage threshold, undervoltage threshold, overcurrent threshold, trip delay, recovery delay, voltage/current correction).
  3. Adjust Values: When the desired parameter is displayed, use the "+" and "-" buttons to adjust its value.
  4. Save Settings: Press the "SET" button again to confirm the value and move to the next parameter, or wait for a few seconds for the device to automatically save and exit setting mode.

6.3 Protection Functions

  • Overvoltage Protection: If the voltage exceeds the set overvoltage threshold, the device will trip and cut off power to the load. The display will indicate an overvoltage fault.
  • Undervoltage Protection: If the voltage drops below the set undervoltage threshold, the device will trip and cut off power to the load. The display will indicate an undervoltage fault.
  • Overcurrent Protection: If the current drawn by the load exceeds the set overcurrent threshold, the device will trip and cut off power. The display will indicate an overcurrent fault.
  • Automatic Reclosing: After a trip event (overvoltage, undervoltage, or overcurrent), the device will automatically attempt to reclose and restore power after a set recovery delay, provided the fault condition has cleared.
  • Manual Switch: The ON/OFF button allows for manual interruption or restoration of power. If the device has tripped due to a fault, you can manually resume operation using this button once the fault is resolved.

7. Maintenance

  • Keep the device clean and free from dust and moisture.
  • Periodically check wiring connections for tightness and signs of wear or corrosion.
  • Ensure adequate ventilation around the device to prevent overheating.
  • Do not attempt to open or repair the device yourself. Refer to qualified service personnel.

8. Troubleshooting

Device does not power on:
Check the incoming power supply and ensure all wiring connections are correct and secure. Verify the upstream circuit breaker is not tripped.
Device trips frequently:
Check the display for the fault type (overvoltage, undervoltage, or overcurrent). Adjust the protection thresholds if they are set too sensitively for your application. Ensure your load does not exceed the device's maximum rated current.
Incorrect voltage/current readings:
You can use the voltage/current correction parameters in the setting mode to fine-tune the readings if you have a calibrated reference meter.
Automatic reclosing does not work:
Ensure the fault condition has cleared. Check the recovery delay setting; if it's too long, it might appear as if it's not reclosing. If the fault persists, the device will not reclose.

9. User Tips

  • Before setting parameters, familiarize yourself with your local power grid's typical voltage and current draw of your connected appliances to set appropriate protection thresholds.
  • For critical loads, consider setting the trip and recovery times to values that balance protection with operational continuity.
  • Regularly check the kWh display (on LC-AVP-3) to monitor energy consumption for connected circuits.

10. Warranty and Support

For warranty information, technical support, or service, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

A detailed user manual in PDF format may be available for download. Please refer to the official product page or contact customer support for access to the PDF manual.

© LCTC. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.