1. Introduction
The GODIAG GT100 is an advanced ECU connector and protocol communication testing tool designed for automotive diagnostics, programming, and coding. It serves as a versatile platform for detecting OBDII protocol communication, performing ECU maintenance, and facilitating various diagnostic procedures. This manual provides detailed instructions for its setup, operation, and maintenance.
Video: GODIAG GT100 Product Unboxing and Overview
2. Key Features
- OBDII Protocol Detector & Communication Detection: Identifies communication protocols and monitors signal integrity.
- ECU Connection: Supports connection to single or multiple ECU modules for diagnosis, programming, and coding.
- Signal Detection & Electrical Level Conversion: Converts car OBD2 interface into a 6-pin interface for detailed signal analysis.
- Voltage Monitoring: Displays real-time voltage of the vehicle's OBDII interface to prevent data loss during operations.
- Battery Replacement Support: Provides stable power to the vehicle during battery changes, preventing data loss or module lock-up.
- OBD1 to OBD2 Conversion: Facilitates conversion of OBD1 diagnostic interfaces to standard OBD2 protocols.
- Extension Capabilities: Includes extension cables for convenient access in tight spaces or for extended reach.
- Compatibility: Works with various diagnostic tools such as Xhorse VVDI2, Autel devices, Launch, and Foxwell.
3. Components Included
The GODIAG GT100 package typically includes the following items:
- 1x GODIAG GT100 Host Unit
- 1x OBD 2-in-1 Extension Cable
- 1x Colored Jumper Cable Set
- 1x 12V Power Supply Adapter
- 1x 120 Ohm Resistance
- 6x Banana Plugs
- 24x Wire Accessories (Dupont 2.54mm connector female pins)
- 1x Operation Manual
Image: GODIAG GT100 device and all included accessories.
4. Device Overview
The GODIAG GT100 features multiple interfaces for various diagnostic and programming tasks.
Image: Front view of the GODIAG GT100 showing ECU and Tool Connectors, DC (12V) input, and power switches.
Front Panel:
- Car Connect: Input for connecting to the vehicle's OBDII port.
- ECU Connector: Banana plug ports (9-16) for connecting to ECU pins.
- Tool Connector: Banana plug ports (1-8) for connecting to diagnostic tools or other devices.
- DC (12V): Power input for external 12V adapter.
- Digital Display: Shows real-time voltage (V) and current (A).
- Power Switches: For main power, 12V(30) and 12V(15) outputs.
- Auto/Off/Man Switch: For controlling power modes.
Image: Side view of the GODIAG GT100 showing the DB15 and DC interfaces.
Side Panel:
- DB15 Interface: For specific connections, often used with specialized cables.
- DC Interface: Additional DC power input.
Image: Other side view of the GODIAG GT100 showing the DB25 and PS2 GPT interfaces.
Other Side Panel:
- DB25 Interface: For specific connections, often used with specialized cables.
- PS2 GPT Interface: For GPT (General Purpose Timer) connections, typically for advanced programming.
5. Connection Methods
5.1 OBDII Protocol Detector & Communication Detection
- Connect the GODIAG GT100 to the vehicle's OBDII diagnostic port.
- Observe the voltage displayed on the GT100.
- Turn on the power switch of the GODIAG GT100.
- Connect your diagnostic tool to the GT100.
- When the diagnostic tool communicates with the car, the LED indicators corresponding to the active protocol (e.g., CAN-H, CAN-L) will light up or flash. A bright LED indicates strong signal, while dimming or weak twinkling suggests successful communication.
Image: Setup for OBDII Protocol Detection and Communication Monitoring.
5.2 ECU Single Module Connection
The GT100 allows for isolated diagnosis and programming of a single ECU module.
- Connect the ECU module to the GT100 using the colored jumper cables. Ensure correct pin assignments. If the ECU uses CAN protocol, verify if a 120 ohm resistor is required and connect it if necessary.
- Power the GT100 either by connecting it to the vehicle's OBDII diagnostic interface or by using the provided AC power adapter.
- Connect your diagnostic tool or ECU programmer to the GT100 to perform diagnosis or programming on the single ECU.
Image: Connection for single ECU module diagnosis and programming.
5.3 Banana Plug Extension Connection
Extend the vehicle's OBDII 16-pin interface for easier access and waveform testing.
Image: Using banana plugs to extend the OBDII interface for testing.
5.4 OBD1 to Standard OBD2 Conversion
Use the GT100 to convert an OBD1 interface to a standard OBD2 interface based on the diagnostic communication protocol.
Image: Converting an OBD1 diagnostic interface to OBD2 using the GT100.
5.5 Multiple ECU Control Module Connection
For professional engineers, the GT100 allows connecting and working with multiple ECU control modules simultaneously for detection and maintenance.
Image: Setup for connecting multiple ECU control modules.
5.6 Using Extension Cables
If the diagnostic interface location is difficult to access or the diagnostic cable is too short, use the provided extension cables (up to 1.2 meters) for convenience.
Image: Illustration of using extension cables for improved accessibility.
5.7 Powering the Car During Battery Replacement
To prevent data loss or module lock-up when replacing a vehicle's battery:
- Connect a fully charged external battery (Battery A) to the GODIAG GT100 via pins 16 (positive), 4 (ground), and 5 (signal ground) and then connect the GT100 to the vehicle's OBD2 diagnostic interface.
- Turn on the power switch of the GODIAG GT100.
- Important: Do not turn on the ignition switch or start the car during this process.
- Once Battery A is providing stable power through the GT100, remove the old battery from the car and replace it with the new battery (Battery B). This ensures continuous power to the vehicle's control modules.
Image: Procedure for maintaining vehicle power during battery replacement.
5.8 Truck Diagnostic Interface Conversion
The GT100 can convert the OBD1 port of special trucks to a standard OBD2 diagnostic port, enabling compatibility with standard OBD2 diagnostic tools.
Image: Setup for converting a truck's OBD1 diagnostic interface to OBD2.
6. Operating Instructions
6.1 Monitoring OBDII Interface Voltage
The GT100 continuously monitors the voltage of the vehicle's OBDII interface and displays it in real-time. It is crucial to observe this voltage:
- If the displayed voltage is less than 11V, immediately stop any ongoing diagnosis or programming. Continuing operations with low voltage can lead to the vehicle being unable to start, data loss in control modules, or modules becoming locked.
6.2 Understanding OBDII Pinout and Indicator Meanings
The GT100's LED indicators correspond to specific pins on the OBDII interface, providing visual feedback on communication and power status.
Image: OBDII Pinout diagram with corresponding LED indicators on the GT100.
| Pin Number | Function |
|---|---|
| 1 | Manufacturer Custom |
| 2 | SJE1850 Wire |
| 3 | Manufacturer Custom |
| 4 | Power Grounding |
| 5 | Signal Grounding |
| 6 | SAEJ2284 (CAN) High |
| 7 | ISO9141-2 & ISO/DIS 4230-4K Wire |
| 8 | Manufacturer Custom |
| 9 | Manufacturer Custom |
| 10 | SJE1850 Wire (Bus-) |
| 11 | Manufacturer Custom |
| 12 | Manufacturer Custom |
| 13 | Manufacturer Custom |
| 14 | SAEJ2284 (CAN) Low |
| 15 | ISO9141-2 & ISO/DIS 4230-4L Wire |
| 16 | Car Battery Positive |
Image: Detailed hardware connection diagram for various pin configurations.
Image: Overall connection diagram illustrating various uses of the GODIAG GT100.
7. Specifications
| Item | Specification |
|---|---|
| Diagnostic Port | OBDII |
| Working Voltage | DC 9V-24V |
| Work and Power Consumption | 0.5-0.6W |
| Adapter Power Input | AC100V-240V |
| Adapter Power Output | DC12V 1A |
| Operating Temperature Range | -20 to 70 °C (-4 to 158 °F) |
| Storage Temperature Range | -40 to 85 °C (-40 to 185 °F) |
| Dimensions (L x W x H) | 23cm x 18cm x 7cm |
| Weight | 1.1 kg |
8. Troubleshooting
- No Communication / Intermittent Communication: Check all cable connections to ensure they are secure. Verify the vehicle's OBDII port is functioning correctly. Observe the GT100's LED indicators for the active protocol; if they are dim or not flashing as expected, there might be a communication issue.
- Low Voltage Warning: If the GT100 displays a voltage below 11V, immediately cease diagnostic or programming activities. Connect an external stable 12V power source to the GT100 or the vehicle to prevent potential damage or data loss.
- Incorrect Pinout: Refer to the 'OBDII Pinout and Indicator Meanings' table and the hardware connection diagrams to ensure correct pin assignments, especially when connecting directly to ECUs or using custom setups.
9. User Tips
- Always ensure a stable power supply to the GT100 and the vehicle during critical operations like ECU programming to avoid interruptions.
- When working with CAN protocol ECUs, remember to check if a 120 ohm resistor is needed for proper communication.
- Utilize the extension cables for better ergonomics and access, especially in confined engine bays or under dashboards.
- Keep the operation manual handy for quick reference to pinouts and connection diagrams.
10. Warranty and Support
The GODIAG GT100 comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. For technical support, warranty claims, or any inquiries, please contact your authorized GODIAG distributor or the official GODIAG support channels. Please retain your proof of purchase for warranty validation.