Introduction
This manual provides essential information for the safe and efficient operation, assembly, and maintenance of your KORNORGE M20 Adult Electric Bicycle. Please read this manual carefully before using the product to ensure proper understanding of its performance and to prevent personal injury or property damage. Keep this instruction manual properly for future reference.
Disclaimer:
Our company reserves the right to modify and give final interpretation to the product model, specification, and other information contained in this manual. The functions of the specific model referred to in this manual apply to this specific model only. The product model, specification, and other information contained in this manual is subject to any modification or change without notice. Without the prior written permission of the company, the contents of the manual may not be copied, modified, reprinted, disseminated or published in any form. Please read this manual carefully before using the product, and operate in accordance with the manual. Otherwise, the company shall not be liable for any personal or property damage, including damage to the product, caused by misuse or abuse.
Safety Precautions
WARNING:
- Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
- While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
- Do not use the eBike before reading this manual carefully and knowing your eBike thoroughly.
- This eBike is designed for riders aged 16-45. Anyone aged below 16 is strictly forbidden to ride this eBike.
- Always wear a helmet when riding.
- Do not lend your eBike to anyone who does not know how to use it, to avoid harm.
- Do not exceed the load capacity of 120 kg (or 264.60 lbs.).
- Obey local traffic rules, keeping to the right or left as required.
- Do not ride on any motorized lane or in any pedestrian crowd.
- It is advisable not to go over 15 km/h (or 9.32 mph) when riding on any non-motorized lane, downhill, or paved road.
- Slow down in rain or snow as required braking distances increase.
- It is advisable not to ride in storms or any extreme weather.
- Avoid impact on the motor.
- Do not park your eBike in any lobby, walkway, evacuation stairway, or emergency entrance/exit.
- Do not charge or park your eBike inside any residential building. Keep away from combustibles when charging. Charging should not exceed 6 hours each time.
Parts & Components
Familiarize yourself with the different parts of your KORNORGE M20 eBike.
List of Components:
- Brake Lever
- Thumb Shifter
- Front Reflector
- Handlebar
- Wiring Harness
- Front Light
- Front Fork
- Front Fender
- Tire
- Rim
- Brake Disc
- Front Wheel Reflector
- Front Disc Brake Caliper
- Front Fender Bracket
- Pedal
- Crank Arm
- Chainring
- Controller
- Chain
- Kickstand
- Rear Wheel Reflector
- Spoke
- Motor
- Rear Derailleur
- Freewheel
- Rear Fender Bracket
- Rear Fender
- Frame
- Rear Light
- Seat
- Shock Absorber
- Battery
- Power Switch
- Display
- Half-Twist Throttle
- Handlebar Grip
Note: As eBikes are upgraded, your specific model may differ slightly from the one shown above, but the usage instructions remain the same.
List of Accessories
- Pedals (x2)
- Charger (x1)
- Manual (x1)
- Open wrench (x1)
- Allen key (x1)
Setup & Assembly
Unboxing and Initial Assembly
- Open the box, carefully take out your eBike, and remove all packaging materials.
- Assemble the front wheel: Mount the front wheel to the front fork. Tighten the nuts securely with a 15mm Open wrench.
- Align the handlebar: Align the handlebar with the stem, then tighten the screws with a 5mm Open wrench.
- Brake Check: Gently pull the brake levers a couple of times to ensure both the front and rear brakes function normally and that there is no abnormal sound from the turning wheels.
- Install the pedals: Install the pedals and tighten them up.
Remark: Please wear a helmet when riding the eBike.
Installing the Front Wheel (Detailed)
I. Basic Mechanical Principle with Hub and Anchor Nuts:
Turn the anchor nuts clockwise to increase clamping, and anti-clockwise to decrease.
II. How to Install:
- Manually turn the anchor nuts anti-clockwise to loosen for space, and insert the front wheel all the way into the dropouts of the front fork.
- Manually turn the anchor nuts clockwise to fasten up. Ensure that the front wheel is located at the very center of the front fork, and that the disc brake rotor is parallel to the disc brake caliper towards the end of the front fork with space in between. Keep some space on both sides, and tighten into place with a spanner as indicated below.
Installing the Pedals
- Insert the pedal marked "R" (Right) into the right crank. Hold the pedal with your hand, and turn it clockwise for a few rounds. Then clamp the pedal shaft with the spanner provided in the package, and turn it clockwise until fastened.
- Find the "L" (Left) pedal and repeat the above steps, but rotate counter-clockwise.
- If you feel resistance when turning the pedal shaft, immediately remove the pedal to avoid possible damage. Attach the pedal again and make sure the pedal shaft is perpendicular to the threaded hole on the crank. Proceed with the rest of the steps.
Important: Screw in the right pedal clockwise, and the left pedal counter-clockwise.
Installing the Shock Absorber
- Remove the countersunk bolts from the frame with the hex key.
- Align the eyelets of the shock absorber and the frame.
- Pass the countersunk bolts through the eyelets, and fasten to secure.
Charging the Battery
Please use the original charger that comes with the eBike. Connect the DC jack of the charger to the charging slot of your eBike, and then the AC plug to the mains. When the charging starts, the red light on the charger turns on. The charger light turns from red to green when charging is complete.
Important Charging Notes:
- When the battery does not need charging, do not keep the AC plug connected to the mains, and do not keep the charger connected to the battery.
- Do not charge indoors. When charging outdoors, avoid rain or direct sun on the charger.
- Charge the battery only at temperatures between 0°C (32°F) and 45°C (113°F).
- The charging current should not exceed 2A.
- Do not charge the battery for over 6 hours each time.
- If the charging indicator appears abnormal, a smell is released, or the charger overheats, stop charging immediately. Service or replace the charger.
- To stop charging, unplug from the mains before disconnecting the charger and battery.
- When the charging indicator turns green, stop charging.
- Do not leave the charger connected to any AC power source when not charging.
- Make sure to charge the battery for two hours each month if not in use.
Operation
Display & Buttons
The KORNORGE M20 features a central display and control buttons for various functions.
1. Power Button
- Power ON/OFF: Press and hold for 2 seconds to power ON/OFF. When powered ON, all icons on the display will illuminate briefly.
- Parameter Display: Short press to cycle through TRIP / VOLT / ODO. Factory default: TRIP.
- Speed Unit: Double press to switch km/h ↔ mph. Factory default: km/h.
- Cruise Control: Triple-press to enable/disable cruise control. (When enabled, the cruise icon will illuminate; if abnormal, the icon may flash.) When braking or accelerating, cruise control will exit automatically. Factory default: cruise control OFF.
2. Left Button
- Headlight: Press and hold for 2 seconds to turn the headlight ON/OFF. When powered ON, the daytime running light is ON by default.
- Assist Up: Single press to increase assist level.
3. Right Button
- Walk Assist Mode: Press and hold for 2 seconds to enter walk assist mode (6 km/h, pedestrian icon ON).
- Assist Down: Single press to decrease assist level.
- Mode Switching (Gear Mode): With power OFF, press and hold the power button for 10 seconds to enter mode settings.
Three modes are available:
- Factory default "F0": Level 0 = no assist.
- Factory default: Highest mode available.
Gears and Derailleur System
The KORNORGE M20 eBike comes with a gear system for varied riding conditions.
The gear mechanism consists of:
- Rear sprocket cluster (freewheel or cog set)
- Rear derailleur
- Shifter
- Control cable
- Front sprocket (chainring)
- Drive chain
A downshift (to a lower/slower gear) makes pedaling easier, while an upshift (to a higher/faster gear) makes pedaling harder. You can upshift to go faster and downshift to go uphill. Shifting is only possible when pedaling forward, ensuring the drive chain is moving and under tension.
CAUTION:
Never shift when pedaling backward. Also, do not pedal backward after a shift. Either action may jam the chain and cause serious damage to your eBike.
Derailleur System Adjustment
Although the front and rear derailleurs are initially adjusted at the factory, you should inspect them before each ride.
Adjustment Steps:
- Twist the shifter to the largest number indicated. This will loosen the anchor bolt on the rear derailleur, placing the chain on the smallest sprocket.
- Adjust the high limit screw so that the guide pulley and the smallest sprocket are lined up vertically.
- Re-tighten the cable, pull out any slack, and re-tighten the anchor bolt securely.
- Shift through the gears, making sure that each gear is achieved quietly and swiftly.
- If necessary, use the barrel adjuster to fine-tune the cable tension. Turning it clockwise loosens cable tension and moves the chain away from the wheel. Turning it counter-clockwise tightens cable tension and directs the chain towards the wheel.
Maintenance
Regular maintenance ensures the longevity and safe operation of your KORNORGE M20 eBike.
- The front and rear wheels should be aligned to the center of the front fork and frame.
- Park away from direct sunlight and rain.
- Do not rinse the eBike directly with water. Wipe with a damp cloth to clean.
- Check the motor and brakes frequently. Do not oil the braking system.
- Regularly check all screws and keep them fastened.
- Keep the bearings lubricated.
- Regularly check the tension of the chain, which can be adjusted via the chain regulator.
- Frequently check the tires for scratches, cracks or excessive wear. The inner tube and valve should be perpendicular to the wheel hub. Punctured, damaged or excessively worn inner tube and tire must be replaced immediately. Please contact professional technicians.
Recommended Torque Specifications
- Handlebar screw: 60-80 kgf.cm (52.08-69.44 lbsf.in)
- Steering stem screw: 175-200 kgf.cm (151.90-173.60 lbsf.in)
- Saddle screw: 175-250 kgf.cm (151.90-217.00 lbsf.in)
- Wheel screw: 320-450 kgf.cm (277.70-390.60 lbsf.in)
Battery Storage
- When not in use, store the battery in a dry place (relative humidity at 65±20%) and cool place (temperature at 10-35°C, or 50-95°F).
- Keep away from fire, heat, and high temperature.
- Do not put the battery in acid or alkaline liquid.
- Waste battery is classified as hazardous. Do not disassemble the waste battery on your own. It should be collected and recycled properly.
Troubleshooting: Error Codes
The display may show error codes to indicate specific issues. Refer to the table below for descriptions.
| Code | Description |
|---|---|
| 1 | Throttle |
| 2 | Brake |
| 11 | Motor Stall |
| 12 | Overcurrent |
| 13 | Communication |
| 14 | Overvoltage |
| 15 | Undervoltage |
| 16 | Phase Fault |
| 17 | Hall |
| 21 | Stall |
If you encounter an error code not listed or cannot resolve an issue, please contact professional technicians.
Specifications
| Category | Detail | |
|---|---|---|
| Build | Model | M20 |
| Body material | High-carbon steel | |
| Expanded size | 1820*690*1140MM | |
| Folded size | Not foldable | |
| Wheelbase | 1190mm | |
| Ground clearance | 150mm | |
| Net weight | 39.2KG | |
| Performance | Max Load | 120 kg (264.55 lbs) |
| Riding speed | 25 km/h | |
| Max speed | 25 km/h | |
| Range in Throttle Mode | 72 km | |
| Range in Pedal Assist mode | 80± km | |
| Hill climbing capacity | 15 degrees | |
| Operating temperature | -10°C - 45°C (14°F - 113°F) | |
| Core | Battery type | 18650 Lithium-ion Battery |
| Battery capacity | 18.2 Ah | |
| Battery rated voltage | 48V | |
| Charging voltage | DC54.6V | |
| Charger input voltage | AC100-240V | |
| Charging time | 8-9 hours | |
| Motor type | High-speed motor | |
| Motor rated voltage | 48V | |
| Features | Headlight | Yes |
| Pannier rack | Yes | |
| Braking | Front and rear disc brakes | |
| Pedal assist sensor | Speed sensor | |
| Adjustable seat height | NO | |
| Other Features | The eBike powers off automatically after ten minutes of inactivity. | |
Note: The max speed may vary, depending on the battery level, load, tire pressure, terrain, lubrication state of the chain and bearings, etc. The ranges are determined upon tests at the ambient temperature of 25°C (or 77°F), at the speed of 15 to 20 km/h (or 9.32 to 12.43 mph), on smooth and firm terrain, with a load of 60 kg (or 132.30 lbs), and within an uninterrupted period from full to zero battery level. The ranges may vary, depending on your riding behavior, ambient temperature, load, tire pressure, terrain, etc.
User Tips
Based on common user experiences and questions, here are some helpful tips for your KORNORGE M20 eBike:
- App Functionality: The M20 supports smart App connection for additional functional controls. Scan the QR code provided in the manual to download the Vicent Scooter APP for Android/iOS. This app supports one-click device pairing, real-time data display, usage record storage, and product management.
- Tire Pressure: Maintain tire pressure between 35-45 PSI for optimal performance and safety.
- Battery Care: Always use the original charger. Avoid overcharging and store the battery in a cool, dry place. Remember to charge it for at least two hours monthly if not in regular use.
- Gear Shifting: Always pedal forward when shifting gears to prevent chain jamming and damage.
- Safety First: Always wear a helmet and adhere to local traffic laws. Be extra cautious in adverse weather conditions like rain or snow.
Warranty & Support
It is forbidden to modify key structural parts including the frame, front fork and steerer tube, and any electrical parts. If damaged, replace with identical parts from our factory. Otherwise, the warranty shall be void and the owner shall take sole responsibility for any consequence.
For further assistance, troubleshooting, or to report issues, please contact the manufacturer or authorized service center. Refer to the official PDF user manual for additional details: KORNORGE M20 User Manual (PDF).