Superun CT06-B

Contents

Superun Raceable Treadmill User Manual

Model: CT06-B

Brand: Superun

1. Safety Precautions

⚠ CAUTION: Please adhere to the directives outlined below to prevent harm to yourself or others.

  1. Prior to initiating use of the treadmill, ensure it is effectively grounded, thus mitigating potential risks and accidents.
  2. While using the treadmill, attach the safety lock (red) clip to your clothing properly, so that in case of emergency, the safety lock can be pulled off immediately to stop the treadmill for your safety.
  3. (1) Consult a medical professional before commencing an exercise regimen.

    (2) Wear appropriate athletic shoes during exercise sessions (avoid running in slippers as they can become entangled with the machine, leading to malfunction).

    (3) Maintain a tidy surrounding to prevent dust particles from accumulating on the treadmill causing mechanical issues.

  4. This particular model of the treadmill was designed for individual use only. Avoid proximity to children or pets at any time while the treadmill is operational to avoid potential incidents.
  5. When fully extended, provide a minimum clearance between the treadmill and the walls and furniture (at least three feet on each side).
  6. Discontinue using the treadmill should the power cord be damaged.
  7. Should the treadmill malfunction or sustain damage, it is imperative to cease use. We kindly request you reach out immediately to your local distributor for prompt repair service.
  8. Refrain from touching any moving parts manually. Also, kindly refrain from jamming or forcing items into the mechanism of the treadmill.
  9. The treadmill should only be utilized indoors, avoiding exposure to extreme outdoor temperatures or potentially-unsanitary gym conditions.
  10. Place the treadmill on clean and flat ground, keep the treadmill well ventilated, make sure there's no sharp object nearby, and do not use the treadmill near water and heat sources.
  11. Use the handrail when getting on and off the treadmill. Do not get off before the treadmill stops completely. For any emergency when you need to jump off, remove the safety lock to stop the treadmill immediately.
  12. Do not utilize the treadmill near respiratory equipment or aerosols or sprays causing a mist.
  13. To sustain the optimal operation of the treadmill, do not install or attach any accessories or components that are not part of the original assembly provided by the manufacturer of the treadmill.
  14. Ensure all components of the treadmill are assembled and secured properly.
  15. Always turn off the power supply and unplug the treadmill's power cord following use.

2. Product Overview

Product Chart

The two styles have the same functions but differ only in appearance. Please refer to the actual item received.

Style 1

Superun Treadmill Style 1 Diagram

Diagram of Superun Treadmill Style 1, highlighting components like Phone stand, Electronic watch button, Safety Key, Handrail, Column, Quick release wrench, and Running table.

Style 2

Superun Treadmill Style 2 Diagram

Diagram of Superun Treadmill Style 2, highlighting components like Phone stand, Electronic watch button, Safety Key, Handrail, Column, Quick release wrench, and Running table.

Technical Parameters

Parameter CT06-B/A6 Pro CT06-C/A6 Plus
Voltage (V)120120
Peak horsepower (HP)3.03.0
Max Load (lbs)300300
Product Size (inches)45.45 * 21.77 * 41.8549.39 * 21.77 * 45.79
Running Area (inches)14.96 * 37.4014.96 * 41.34
Speed (MPH)0.6-7.50.6-7.5
Net Weight (lbs)50.4954.54

Note: The above data is manual measurement, there may be some deviation. Please refer to the actual received product. Locate the device model in the carton.

⚠ Warning: Before plugging the power cord into the outlet, verify that the field voltage requirements match the voltage of the received treadmill. The power requirements of the device include a dedicated circuit that is grounded and rated at one of the following: the voltage in the United States is typically 120 volts, 60 Hz; Canada 120 volts, 60 Hz; The voltage in the United Kingdom is 240 volts, 50 Hertz; The voltage in Spain is 230 volts, 50 Hertz; The voltage in Italy is 230 volts, 50 Hertz; The voltage in Germany is 230 volts, 50 Hertz; The voltage in France is 230 volts and the frequency is 50 Hertz.

Parts List

No. Name Picture Quantity Note
1Main FrameMain Frame of the treadmill1 piece
2Phone StandPhone Stand on the console1 piece
3Safety LockSafety Lock key1 piece
4Power CordPower Cord1 piece
5Remote ControlRemote Control unit1 piece
6OilLubrication oil bottle1 piece
7L-type 6mm hex socket (dual purpose)L-type hex socket tool1 piece
8Hex ScrewHex Screw2 pieces
9Left handrailLeft handrail1 piece
10Right handrailRight handrail1 piece
11Square multi-function wrenchSquare multi-function wrench1 piece
12Knobs of the columnsKnobs for the columns2 pieces
13ManualUser Manual1 piece
14Quick & Easy GuideQuick & Easy Guide1 piece

3. Assembly and Installation Steps

The installation steps for both styles of treadmills are identical. The following operations will be demonstrated using Style 1 as an example.

Step 1: Unpack and Position Main Unit

Treadmill main unit laid flat on the ground

Open the package, take out the assembly material, and lay the main unit flat on the ground.

Step 2: Raise the Column

Raising the treadmill column into position

Put up the column in the direction of the arrow.

Step 3: Tighten Column Knobs

Tightening the treadmill column knobs clockwise

Once the column is in position, tighten the knobs at the base of the column by turning them clockwise, as indicated by the arrow.

Step 4: Insert PAD Frame

Inserting the PAD frame into the treadmill console

Insert the PAD frame.

Step 5: Attach Handrails

Attaching handrails to the treadmill column

Align the side handle mounting holes with the column holes, insert the long screw into the holes, and tighten it using an L-type 6mm hex socket.

Step 6: Secure PAD Support Nut (if loose)

Tightening the PAD support nut with a square multi-function wrench

If the PAD support nut is loose, use a square multi-function wrench to tighten it clockwise.

Step 7: Position Safety Switch

Positioning the safety switch on the treadmill console

Place the electronic table yellow sticker position on the safety switch. Power can operate the treadmill.

4. Operating Instructions

Switching Between Walking and Running Modes

  1. Turn off the treadmill and make sure it is not running.
  2. Rotate the side handles backward until they are parallel with the column, and then remove the PAD bracket.
  3. Turn the column knob counterclockwise as indicated by the arrow and lower the column. (Note: Please ensure safety to prevent the column from suddenly dropping and hitting anyone.)
  4. Restart the treadmill and operate it within a speed range of 0.6 to 3.8 mph (using the remote control).
Treadmill in walking pad mode with handle folded down

Image showing the treadmill in walking pad mode (handlebar folded down).

Treadmill in running mode with handle raised

Image showing the treadmill in running mode with the handlebar raised.

Adjusting the Incline

To increase the workout difficulty by adjusting the incline, follow these steps:

  1. Turn off the treadmill and make sure it is not running.
  2. Carefully lift the rear of the treadmill (be sure to prevent it from falling and causing injury).
  3. Pull up the incline frame on both sides and secure the frame in place.
  4. Lower the treadmill back down and ensure it is stable.
  5. Once the treadmill is stable, turn it back on to resume normal use.

To lower the incline, follow the same steps in reverse.

Treadmill incline adjustment diagram

Diagram illustrating the manual incline adjustment mechanism, showing the treadmill being lifted and the incline frame being secured.

Display and Key Functions

When the machine is running, the display window automatically switches every 5 seconds. The indicator light at the bottom of the full window changes with the display of the window. The information displayed in different Windows is as follows:

Treadmill display panel showing time, speed, distance, calories, WIFI, and Bluetooth indicators

Close-up of the treadmill's LED display panel showing time, speed, distance, and calories, along with WIFI and Bluetooth indicators.

  • 01. "WIFI" window: Displays the WIFI indication. The icon will light up when the WIFI connection is successful.
  • 02. "Bluetooth" window: Displays the Bluetooth indication. The icon will light up when the Bluetooth connection is successful.
  • 03. "Speed" window: The current speed value is displayed in the running state.
  • 04. "Time" window: Displays exercise time.
  • 05. "Distance" window: Displays the moving distance.
  • 06. "Calories" window: Displays the calorie consumption value.

Window Value Display Range

Setting Parameter Initial Value Display range
Time (minutes: seconds)0:000:00-99:59
Speed (mph)0.60See Technical Parameter-Speed for details
Distance (miles)0.000.00-99.99
Calories (kcal)0.000.00-9999

Control Buttons

Treadmill control panel buttons for Start/Pause, Stop, Speed adjustment, and quick speed shortcuts

Close-up of the treadmill's control panel, showing Start/Pause, Stop, Speed adjustment (+/-), and quick speed shortcuts (3 mph, 6 mph).

  • 01. Start/Pause button: In standby, press to activate, then press again to start. In operation, press to pause while retaining data, then press again to continue.
  • 02. Stop Button: In operation, press to stop the treadmill and clear exercise data.
  • 03. Speed Increase and Speed Decrease buttons (+/-):
    • Short press (1 second) to increase/decrease speed by 0.1 MPH.
    • Long press (over 1 second) to increase/decrease speed by 0.5 MPH.
  • 04. Speed Shortcuts (3, 6 MPH): Touch the Speed Shortcut key 3 to set speed to 3.0 MPH and key 6 to 6.0 MPH, and jump back to the Speed Display.

Remote Control

Treadmill remote control with ON/OFF, Speed+ and Speed- buttons

Image of the treadmill's remote control with ON/OFF, Speed+ and Speed- buttons.

  • Press the "Speed -" key to reduce the machine speed.
  • Press the "Speed +" key to increase the machine speed.
  • Press the "ON/OFF" button to start or stop the machine slowly.
  • In standby, directly press "ON/OFF" to start the treadmill at 0.6 MPH. Other windows will count up from 0. Use "+", "-" buttons to change speed.

Startup Instructions

  1. Stick the safety lock to the safety lock position on the panel. Turn on the power switch; the buzzer will beep and the system will go to standby.
  2. Press the START key. The window shows a 3-second countdown, and with each beep, the motor will not start.
  3. Start-up speed is: 0.6MPH. At this time, you can press the speed + and - keys to adjust the speed.

Guidance on Operation of PitPat App

The treadmill allows connection to your phone via Bluetooth.

PitPat App QR code and NFC tag on the treadmill console

Image showing the PitPat App QR code and NFC tag on the treadmill console for easy download and connection.

  1. Download the PitPat App on your phone and install it or scan the QR code below to download and install the app.
  2. Open the PitPat App and follow the instructions therein to sign in or register your account information.
  3. Connect the treadmill:
    • (1) Turn on the Bluetooth function of the mobile phone (Android phone) and enable the positioning function.
    • (2) Open the PitPat App (If a prompt is given from the App for authorization, please grant the relevant permissions to the app).
    • (3) Go to the application home page and click a corner of the treadmill icon on the upper right to enter the search interface. Your phone will automatically search for nearby devices. Turn on the treadmill (the device that starts with PitPat-T represents your treadmill) to enable connection. When the treadmill makes a beep, it means the connection is successful, and the Bluetooth icon on the treadmill panel will light up.

Note: When connecting, make sure your phone is connected to the Internet to control the treadmill via Bluetooth. For details about the network configuration, please refer to descriptions in the APP.

System requirements: iOS 13 or above; Android 6.0 or above.

Connecting to WiFi

Reminder: If the treadmill is not connected to PitPat, the Bluetooth icon on the treadmill will be inactive. Conversely, if the treadmill has successfully linked with the app, the Bluetooth symbol shall be active on the machine.

User Guide for Configuring the WiFi Connection on Your Treadmill

Upon successful connection between your treadmill and the mobile app, you will be directed to the WiFi configuration screen of the treadmill. Please note that our model is exclusively compatible with a 2.4GHz frequency range (as indicated on the app, only the 2.4GHz WiFi signals detected on the treadmill will appear). Therefore, ensure that your internet access point can support 2.4GHz frequencies.

  1. Identify the network you require to connect to.
  2. Enter the required WiFi password as per onscreen instructions. Upon establishment of a viable internet connection, the Bluetooth icon located on the display panel of the treadmill will illuminate, signifying that your application has returned to the primary homepage.
  3. Note: In the event that the WiFi connection fails or is disrupted, wait until the WiFi signal stabilizes before restarting the treadmill in order to reconnect to the internet.

5. Maintenance

Proper maintenance helps keep the treadmill in the best condition while improper maintenance may damage or shorten the life span of the treadmill.

Belt Adjustment

  • 01. Running belt tilted:
    • If tilted to the left, adjust screws 1-2 turns clockwise to the left.
    • If tilted to the right, adjust screws 1-2 turns clockwise to the right.
    • Test run. If still tilted, repeat until aligned.
  • 02. Running band tension:
    • If too tight (stronger resistance), turn screws on both sides counterclockwise 1-2 turns to loosen until it stops slipping or pausing.
    • If too loose, turn screws on both sides 1-2 turns clockwise.

⚠ Warning! Don't overtighten the rollers! This can cause permanent damage to the bearing!

Treadmill belt adjustment diagram

Diagram showing how to adjust the treadmill running belt if it is tilted or too loose/tight.

Lubrication

  • The treadmill must be lubricated after half a year or a cumulative run of 100 hours. Add 1/3 to 1/2 bottle at a time.
  • Confirm lubrication status: With the treadmill off, lift the running belt from one side and reach for the surface underneath. If lubricant can be touched, no need to add more. If dry, refill. (Use only non-petroleum-based lubricants).
  • Follow the figure below to properly add the lubricant:
    1. Clean the treadmill.
    2. Turn off the power, lift the running belt, and apply silicone oil to the inner surface.
    3. Start the treadmill and lubricate at 3 mph for 10-20 seconds.
Treadmill lubrication diagram

Diagram illustrating the steps for lubricating the treadmill belt, including cleaning, applying oil, and running the treadmill.

General Maintenance Guidance

  1. Regularly clean and maintain the treadmill, ensuring all components are kept immaculate.
  2. After each use, employ a pristine towel or cloth to wipe down vital areas such as the console, depleting sweat and debris. Take care not to allow electrical elements or running belt to come into contact with water.
  3. Position your treadmill in a clean, dry, and moisture-free area. Ensure it is powered off and disconnected from its socket prior to storage.
  4. The product is equipped with wheels for relocation. Prior to shifting, ascertain it is unplugged and correctly folded.
  5. Conduct constant checks on individual parts and ensure they are securely fastened. Replace components exhibiting signs of damage swiftly.
  6. Prior to exercise, the running belt should be appropriately adjusted. With continuous usage, varying degrees of stretching may occur, leading to belt deviation, friction, and slippage. If the belt slips or gets stuck, adjust it for better performance.

6. Troubleshooting: Error Codes and Solutions

Error Code Error Description Troubleshooting Solutions
SAFESafety lock switch falls offRe-attach the safety lock.
Er1Communication failure, electronic panel cannot receive signal
  1. Check for loose, disconnected or damaged communication cables.
  2. Check or replace the electronic panel if needed.
  3. Check or replace the controller if needed.
Er3Overvoltage
  1. Check whether the voltage of the power supply is at a normal level of AC 120V.
  2. Check or replace the controller.
  3. Check or replace the motor.
Er4Overcurrent
  1. Check for overload status.
  2. Check if any mechanical moving part is stuck.
  3. Check the level of film release agent. Lack of agent may increase friction between running belt and board, causing overcurrent.
  4. Check the running board for severe wear.
  5. Check the running belt for severe wear.
  6. Check if any short circuit exists in the motor line.
  7. Check or replace the controller.
  8. Check or replace the motor.
Er5Overload
  1. Check for overload.
  2. Check if any mechanical moving part is stuck.
  3. Check the level of film release agent. Lack of agent may increase friction between running belt and board, causing overcurrent.
  4. Check the running board for severe wear.
  5. Check the running belt for severe wear.
  6. Check if any short circuit exists in the motor line.
  7. Check or replace the controller.
  8. Check or replace the motor.
Er6Motor is not connected
  1. Check for loose or disconnected lines for the motor.
  2. Check or replace the controller.
  3. Assess the need to replace the motor.
Er7Communication failure, controller cannot receive signals
  1. Check for loose, disconnected or damaged communication cables.
  2. Check or replace the electronic panel.
  3. Check or replace the controller.
Er13IGBT Short Circuit
  1. Ascertain whether the treadmill is experiencing severe interference from external signals.
  2. Examine or replace the controller if necessary.
Er14Load Short Circuit
  1. Check if there is any foreign object at the output of the controller that causes a short circuit.
  2. Check or replace the motor.

7. Exercise Guidelines and Recommendations

DECLARATION OF CAUTION: Prior to commencing this or any exercise regimen, it is imperative that you consult your health care professional.

Warm-up exercises enhance blood circulation, providing muscles with increased oxygenation, elevation in body temperature, and preparation for the physical exertion to follow.

Each training session should initiate with a five to ten minutes stretch routine and light movements warm-up. The accompanying illustrations showcase various fundamental stretches. The recommended approach is to undertake a warm-up session prior to executing your workout. For comprehensive warm-up benefits, repeat each stretch for three consecutive sets.

Warm-up

A warm-up exercise of 5-10 minutes is required before each operation.

Breathing

Do not hold your breath during the operation. Normally, when you are ready to restore your movements, breathe through your nose and exhale with your mouth. Breathing should be coordinated with your movements. If you breathe too quickly, you should immediately stop exercising.

Frequency

Muscles in the same area should have 48 hours of rest, that is, the same area can be trained the next day.

Load

According to the individual physical condition to determine the amount of training, and then exercise according to the principle of asymptotic load, muscle soreness is normal at the beginning of training, as long as you continue the exercise, soreness can be eliminated.

Relax

Five minutes of restoring action should be taken after each exercise, especially when the foot muscles are stretched and relaxed to prevent long-term coagulation and maintain muscle elasticity.

Diet

In order to protect the digestive system, you can exercise one hour after a meal. After training, you should eat at least half an hour. During exercise, you should drink less water, especially large amounts of water, so as to avoid increasing the burden on the heart and kidney.

Stretching Exercises

1. Downward Stretch

Downward stretch exercise diagram

Bend knees slightly, stoop body slowly, relax back and shoulders, reach toes with hands. Hold for 10-15 seconds and relax. Repeat 3 times.

2. Hamstring Stretch

Hamstring stretch exercise diagram

Sit on cushion, straighten one leg, pull other leg inward. Touch toes with hands. Hold for 10-15 seconds and relax. Repeat 3 times for each leg.

3. Calf and Heel Tendon Stretch

Calf and heel tendon stretch exercise diagram

Stand with hands leaning against wall, one foot behind. Keep rear leg upright and heel contact. Hold for 10-15 seconds and relax. Repeat 3 times for each leg.

4. Quadriceps Stretch

Quadriceps stretch exercise diagram

Lean against wall, grab right heel with right hand, pull towards hip until tension in front thigh. Hold for 10-15 seconds and relax. Repeat 3 times for each leg.

5. Sartorius (Inner Thigh Muscles) Stretch

Sartorius stretch exercise diagram

Sit on floor, feet facing each other, knees outward. Grab feet with both hands, pull towards groin. Hold for 10-15 seconds and relax. Repeat 3 times for each leg.

8. User Tips

  • Initial Setup: The treadmill is generally easy to set up. Ensure the running belt is properly aligned and lubricated after assembly to prevent chafing and ensure smooth operation.
  • Quiet Operation: While the motor is quiet, the belt itself can generate some noise during operation. This is normal for treadmills in this price range.
  • App Connectivity: The accompanying PitPat app is quick to set up and enhances the training experience with virtual tracks and competition features.
  • Folding Mechanism: To fold the treadmill for storage, you may need to loosen two screws. This allows for compact storage, such as under a bed or in a closet.
  • Suitability: This treadmill is considered suitable for elderly individuals and those in rehabilitation due to its safety features and ease of use.

9. Detailed Specifications

Attribute Value
Brand NameSuperun
Model NumberCT06-B
Running belt length80-120cm
Running belt width50-80cm
With SpeakersYes
Bluetooth connection availableYes
Adjustable slopeYes
ScreenYes (Touchable screen)
Whether or Not 50Vac or 75Vdc or Higher Power SupplyYes
Training SiteWaist, ARMS, Legs, Muscle Relex Apparatus, Waist & Abdomen Exercise, head, Foot, BACK, Hand, Wrist, Hip, Chest, Core, Other
FoldYes (3-in-1 walking/running/foldable)
Type of sportsStrength Training
OriginMainland China
Running Belt Size380*950mm/14.96*37.4 inches
Max Load300 pounds (approx. 136KG)
Walking Speed0.6-3.8 MPH/1.0-6.0 KPH
Running Speed0.6-7.5 MPH/1.0-12.0 KPH
Horsepower3.0hp/2237W
Machine weight22.94kg/50.49lbs
Machine folding size1253*553*124mm/49.33*21.77*4.88 inches
Machine unfolding size1154.5*553*1063mm/45.45*21.77*41.85 inches

10. Warranty and Support

This product is exclusively intended for domestic applications. Any anomalies associated with commercial usage will not be subject to our warranty coverage.

If you experience any issues with the functionality of your product, kindly liaise with your local distributor regarding customer support!

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference;
  2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirement. The device can be used in 0mm exposure condition, compliance with exposure requirements. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

Support Contact Information

  • Phone: +1 888-589-0777
  • Email: support@deerruntreadmill.com
  • Instagram: deerrun_official
  • TikTok: deerrun_official

Note: If your device includes an activation warranty benefit, please follow the instructions on the quick operation card to activate the device before normal use.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.