DykbRadio 70-200MHZ 45W FM VHF RF power amplifier

Contents

45W 70-200MHz RF Power Amplifier User Manual

Model: 70-200MHZ 45W FM VHF RF power amplifier | Brand: DykbRadio

1. Introduction

This manual provides essential information for the safe and effective use of your 45W Class AB linear RF power amplifier. Designed for the 70MHz to 200MHz VHF band, this amplifier is suitable for applications such as FM broadcasting, amateur radio, walkie-talkies, and various transmitters. Please read this manual thoroughly before operation.

Top view of the 45W RF Power Amplifier with SMA connectors
Figure 1: Top view of the 45W RF Power Amplifier.

2. Safety Warnings

  • WARNING: Stay away from children and avoid misoperation.
  • WARNING: Please do not disassemble or modify this product by yourself. Non-professional repairs may cause damage or safety accidents.
  • CRITICAL WARNING: The input and output must be connected before powering on. Failure to do so will result in damage to the amplifier chip due to excessive reflected signals. The user bears full responsibility for improper operation.
  • Always ensure proper grounding for all connected equipment.
  • Do not operate the amplifier in damp or dusty environments.
  • Avoid severe impact or vibration on the product.

3. Specifications

ParameterValue
Frequency Range70 – 200 MHz
Supply VoltageDC 24 – 26V
Max Current< 3A
Input Power Range (recommended)23 – 26 dBm
Max Input Power< 1W
Output Power (max)45W (with cooling fan)
Amplifier ClassClass AB Linear
CoolingExternal fan required (not included)
Filter SectionLC filter pads reserved for customization
Dimensions (excluding SMA)100 x 50.6 x 40 mm
Table of specifications for the RF amplifier
Figure 2: Detailed specifications table.

4. Setup Instructions

  1. Unboxing and Inspection:

    Carefully unbox the amplifier. Check if all accessories are complete and inspect the unit for any visible damage. If any components are missing or damaged, do not proceed with setup and contact support.

    Side view of the RF amplifier showing the heatsink
    Figure 3: Side view of the amplifier with heatsink.
  2. Power Supply Connection:

    Connect a stable DC power supply (24-26V) to the amplifier's VCC and GND terminals. Ensure correct polarity. The amplifier requires a maximum current of less than 3A.

    Close-up of the RF amplifier's power input terminals
    Figure 4: Power input terminals (VCC, GND).
  3. RF Input and Output Connections:

    Connect your RF signal source to the RFIN (input) SMA connector and your antenna or load to the RFOUT (output) SMA connector. It is crucial that both input and output are connected before applying power to prevent damage to the amplifier chip.

    Front view of the RF amplifier showing RFIN and RFOUT SMA connectors
    Figure 5: RFIN and RFOUT SMA connectors.
  4. Cooling System:

    An external cooling fan is mandatory for operation, especially when operating at higher power levels. Attach a suitable cooling fan (not included) to the heatsink to ensure proper thermal management. Operating without adequate cooling can lead to overheating and permanent damage.

    Bottom view of the RF amplifier showing the heatsink fins
    Figure 6: Heatsink for thermal dissipation.
  5. LC Filter Customization (Optional):

    The PCB includes reserved pads for an LC filter. If specific band filtering is required, advanced users can integrate custom LC filter components. For a fully assembled and tuned version with an LC filter for a specific frequency band, contact the manufacturer for customization options.

5. Operating Instructions

  1. Initial Power-Up:

    After ensuring all connections (power, input, output, and cooling fan) are secure, apply power to the amplifier. Monitor the current draw to ensure it is within the specified limits (< 3A).

  2. Input Signal Application:

    Apply your RF input signal to the RFIN connector. The recommended input power range is 23–26 dBm for 45W output at 100MHz. The maximum input power should not exceed 1W to prevent damage.

  3. Monitoring Output:

    Use appropriate RF measurement equipment (e.g., spectrum analyzer, power meter) to monitor the output power and signal quality. Adjust the input signal level as needed to achieve the desired output power without exceeding the maximum 45W.

    Video 1: Demonstration of the amplifier's performance with a signal generator and spectrum analyzer, showing a 100MHz signal at +16.7 dBm (46.7 dBm with 30dB attenuator).
  4. Functional Mode Selection:

    If your setup involves different functional modes (e.g., for various radio applications), select the corresponding mode according to your system's requirements and the basic settings outlined in your overall system's operation manual.

6. Maintenance

  • Cleaning: Keep the amplifier clean and free from dust. Use a soft, dry cloth for cleaning. Avoid using liquids or abrasive cleaners.
  • Environmental Conditions: Ensure the amplifier is operated in a dry, well-ventilated area, free from excessive dust, moisture, and extreme temperatures.
  • Cooling System Check: Regularly inspect the external cooling fan for proper operation and ensure the heatsink fins are free from obstructions to maintain optimal cooling.
  • Connection Integrity: Periodically check all RF and power connections to ensure they are secure and free from corrosion.

7. Troubleshooting

ProblemPossible CauseSolution
No output power / Amplifier not functioningInput/output not connected before power-up; incorrect power supply voltage/polarity; damaged amplifier chip.Ensure RF input and output are connected before applying power. Verify power supply voltage (DC 24-26V) and polarity. If the chip is damaged due to improper operation, replacement may be necessary.
Low output powerInsufficient input power; incorrect frequency; faulty connections; inadequate cooling causing thermal throttling.Increase input power within recommended range (23-26 dBm). Verify operating frequency is within 70-200MHz. Check all RF connections. Ensure cooling fan is operating effectively.
OverheatingNo external cooling fan; obstructed heatsink; excessive input/output power.Install and ensure proper operation of an external cooling fan. Clear any obstructions from the heatsink. Reduce input power if operating without a fan or if ambient temperature is high.
Unstable operation / Signal distortionPoor grounding; impedance mismatch; external interference; lack of LC filter for specific band.Ensure proper grounding. Verify impedance matching for input and output. Shield the amplifier from external interference. Consider adding a custom LC filter if operating in a noisy environment or requiring cleaner output.

8. User Tips

  • Always use a dummy load when testing the amplifier without an antenna to prevent damage.
  • For optimal performance and longevity, invest in a high-quality external cooling fan.
  • If you require precise frequency filtering, consider customizing the LC filter section with components specific to your desired band.
  • Keep the input power within the recommended range to avoid overdriving the amplifier and ensure clean output.

9. Warranty and Support

Information regarding specific warranty terms and customer support contacts was not provided in the product data. Please refer to your purchase documentation or contact the seller directly for warranty claims and technical assistance.

A user manual in PDF format is available for download: User manual (PDF)

© 2023 DykbRadio. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.