WinAPEX HY118A HY118B

Contents

WinAPEX HY118A / HY118B Pen Type Digital Multimeter User Manual

Model: HY118A, HY118B

1. Introduction

The WinAPEX HY118A and HY118B are compact, pen-type digital multimeters designed for electrical testing and troubleshooting. These devices offer a range of functions including AC/DC voltage measurement, resistance, capacitance, frequency, diode, continuity, Non-Contact Voltage (NCV) detection, live wire detection, and phase sequence detection. The HY118A features a black and white display, while the HY118B boasts a VA color reverse display for enhanced readability. Both models include a flashlight for working in dimly lit areas and an auto-ranging function for ease of use.

WinAPEX HY118A and HY118B Pen Type Digital Multimeters with probes
Figure 1: WinAPEX HY118A and HY118B Pen Type Digital Multimeters with included probes.

2. Safety Information

Please read and understand all safety warnings and operating instructions before using this multimeter. Failure to follow these instructions may result in electric shock, fire, or serious injury.

  • Always ensure the multimeter is in the correct function mode before making measurements.
  • Do not exceed the maximum input values specified for each range.
  • Exercise extreme caution when working with voltages above 30V AC RMS, 42V peak, or 60V DC. These voltages pose a shock hazard.
  • Inspect the test leads for damage before each use. Do not use if insulation is damaged or bare metal is exposed.
  • Do not operate the multimeter if it appears damaged or if it is not operating properly.
  • Replace batteries immediately when the low battery indicator appears to ensure accurate readings.
  • Do not attempt to repair or modify the multimeter. Refer servicing to qualified personnel.
  • Keep hands and fingers behind the probe barriers during testing.

3. Product Overview

3.1 Components

  • Pen-type Multimeter Body: Main unit housing the display, buttons, and internal circuitry.
  • Test Probe: Integrated or detachable probe for making contact with circuits.
  • External Test Lead (for HY118B): Additional lead for certain measurements.
  • Battery Compartment: Located at the rear, for AAA batteries.
Three-angle view of the WinAPEX pen-type multimeter
Figure 2: Various views of the pen-type multimeter, showcasing its design.

3.2 Display and Controls

  • LCD Display: Shows measurement readings, function indicators, and battery status. HY118A has a black and white display, HY118B has a VA color reverse display.
  • SELECT Button: Used to cycle through different measurement functions within a mode (e.g., AC/DC voltage, resistance/capacitance).
  • HOLD Button: Freezes the current reading on the display. Press again to release.
  • N/P Button: Activates NCV (Non-Contact Voltage) or Phase Sequence detection mode.
  • Flashlight: Integrated LED light for illuminating the test area.
Close-up of the VA color reverse display screen showing measurements and the flashlight feature
Figure 3: Close-up of the HY118B's VA color reverse display and flashlight in operation.
Image detailing the HY118A model with its black and white display and a list of its core functions.
Figure 4: HY118A model with black and white display and key features.

4. Setup

4.1 Battery Installation

  1. Locate the battery compartment cover on the back of the multimeter.
  2. Use a screwdriver to open the cover.
  3. Insert two AAA batteries, observing the correct polarity (+/-).
  4. Replace the battery compartment cover and secure it with the screw.

Note: Batteries are not included with the device.

4.2 Connecting Test Leads (if applicable)

For models with external test leads (e.g., HY118B), insert the red test lead into the 'VΩmA' input jack and the black test lead into the 'COM' input jack. Ensure connections are firm.

5. Operating Instructions

The multimeter features auto-ranging for most functions, simplifying operation. Use the 'SELECT' button to switch between different measurement types within a mode.

5.1 AC/DC Voltage Measurement

  1. Turn on the multimeter.
  2. Select the voltage measurement mode (usually indicated by 'V' or 'ACV/DCV'). Use 'SELECT' to toggle between AC and DC if needed.
  3. Connect the test probes across the circuit or component to be measured.
  4. Read the voltage value on the display.

5.2 Resistance Measurement

  1. Turn on the multimeter.
  2. Select the resistance measurement mode (usually indicated by 'Ω').
  3. Ensure the circuit is de-energized before measuring resistance.
  4. Connect the test probes across the component.
  5. Read the resistance value on the display.

5.3 Continuity Test

  1. Turn on the multimeter.
  2. Select the continuity test mode (usually indicated by a buzzer icon).
  3. Ensure the circuit is de-energized.
  4. Connect the test probes across the circuit path. A continuous beep indicates continuity (low resistance).

5.4 Diode Test

  1. Turn on the multimeter.
  2. Select the diode test mode (usually indicated by a diode symbol).
  3. Ensure the diode is disconnected from the circuit.
  4. Connect the red probe to the anode and the black probe to the cathode. The display will show the forward voltage drop. Reverse the probes; the display should show 'OL' (Open Line) for a good diode.

5.5 Capacitance Measurement

  1. Turn on the multimeter.
  2. Select the capacitance measurement mode (usually indicated by 'F').
  3. Ensure the capacitor is fully discharged before measurement to prevent damage to the meter.
  4. Connect the test probes across the capacitor terminals.
  5. Read the capacitance value on the display.

5.6 NCV (Non-Contact Voltage) Detection

  1. Press the 'N/P' button to enter NCV mode.
  2. Move the tip of the multimeter close to the wire or outlet you suspect has AC voltage.
  3. If AC voltage is detected, the screen will display '----', the alarm buzzer will sound, and the LED alarm light will turn red.
Image showing NCV induction detection in action, with the multimeter near an outlet.
Figure 5: NCV induction detection in progress.

5.7 Zero Line / Firewire Recognition

  1. Ensure the multimeter is in the appropriate mode for live wire detection (often integrated with NCV or a dedicated 'Live' mode).
  2. Carefully bring the pen tip close to the power test point (e.g., inside an outlet).
  3. Zero Line Detection: If the indicator light is green, the screen displays '-', and the buzzer sounds slower, it indicates a zero line.
  4. Firewire Detection: If the indicator light is red, the screen displays '+', and the buzzer sounds faster, it indicates a live wire (firewire).
Comparison of Zero line detection (green light, '-' on screen) and Firewire detection (red light, '+' on screen).
Figure 6: Visual indicators for Zero Line and Firewire detection.

5.8 Phase Sequence Detection

  1. Switch the multimeter to the 'P' function (phase sequence function).
  2. Measuring Point A: Place the induction pen on the first root phase wire. The LCD will show 'PA' and 'A' (not blinking). Wait for a beep.
  3. Measuring Point B: Place the induction pen on the second root phase wire. The LCD will show 'PB' and 'B' (not blinking). Wait for a beep.
  4. Measuring Point C: Place the induction pen on the third root phase wire. The LCD will show 'PC' and 'C' (not blinking). Wait for a beep.
  5. After measuring all three points, the phase sequence result will be displayed on the screen.
Diagram illustrating phase sequence detection steps (Measuring points A, B, C).
Figure 7: Step-by-step guide for phase sequence detection.

6. Maintenance

6.1 Cleaning

Wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents. Keep the display clean and free from dust.

6.2 Battery Replacement

When the low battery indicator appears on the display, replace the batteries promptly to ensure accurate measurements. Refer to Section 4.1 for battery installation instructions.

6.3 Storage

If the multimeter is not used for an extended period, remove the batteries to prevent leakage. Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • No Display/Power On: Check battery installation and ensure batteries are not depleted. Replace if necessary.
  • Inaccurate Readings: Ensure the correct function mode is selected. Check test lead connections. Replace batteries if low.
  • 'OL' on Display: Indicates an open circuit (resistance/continuity) or out-of-range measurement.
  • No NCV Detection: Ensure NCV mode is active. The voltage source might be too weak or too far from the sensor.
  • Auto Power Off: The multimeter has an automatic shutdown feature to conserve battery life. Press any button to reactivate.

8. Specifications

FeatureSpecification
ModelHY118A / HY118B
BrandWinAPEX
Display TypeDigital Display
Display Counts6000 Counts
Operating ModeAuto Range
DIY SuppliesElectrical
CertificationCE
OriginMainland China
Dimensions182 x 27 x 20 mm
Weight65g
Operating Temperature0 - 40 ℃
DC Voltage Range0 - 600V
DC Voltage Accuracy±(0.8% + 3)
AC Voltage Range0 - 600V
AC Voltage Accuracy±(1.2% + 5)
Resistance Range0 - 60 MΩ
Resistance Resolution0.1Ω (low range)
Resistance Accuracy±(1.2% + 3)
Capacitance Range0 - 60 mF
Capacitance Accuracy±(4.5% + 5)
Frequency Range0 - 10 MHz
Frequency Accuracy±(2.0% + 5)
Diode TestYes
Continuity TestYes
NCV DetectionYes
Live Wire DetectionYes
Phase Sequence DetectionYes
True RMSYes
Data HoldYes
BacklightYes
FlashlightYes
Auto Power OffYes
Low Battery IndicationYes
Power Supply2 x AAA Batteries (not included)

9. User Tips

  • For best accuracy, ensure the test probes are clean and free of corrosion.
  • When measuring resistance or continuity, always ensure the circuit is de-energized to prevent damage to the multimeter and ensure safety.
  • The flashlight feature is useful for illuminating dark work areas, improving visibility and safety.
  • Take advantage of the auto-ranging feature to quickly get readings without manually selecting ranges.

10. Warranty and Support

For warranty information and technical support, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.