1. Safety Information and Precautions
Please read this instruction manual carefully before use to ensure safe and proper operation of your LiTime LiFePO4 battery. Failure to follow these instructions may result in damage to the battery, property, or personal injury.
- Fire Risk: Be aware of potential fire risks. Strictly follow the instruction manual for charging and storage procedures.
- Protective Gear: Always wear insulating gloves when unpacking, installing, or wiring the battery.
- Initial Charge: The battery is shipped with approximately 30% to 50% capacity due to transport regulations. Fully charge the battery before putting it into operation for the first time.
- Battery Orientation: The battery must always be installed upright with the terminal screws pointing upwards. Inverted mounting must be avoided. If side mounting is required, please contact service.de@litime.com for confirmation of correct orientation.
- Compatibility: Do not connect batteries of different brands or with different specifications in series or parallel. This can lead to imbalance and damage.
- Terminal Connections: Tighten the terminal screws with the included socket wrench until they can no longer be turned and the spring washer lies completely flat. Loose battery terminals can lead to heat generation at the terminals, which damages the battery.
- Wiring Harness: After connecting, check that the wiring harness is firmly seated by shaking it vigorously.
- Short Circuit Prevention: Avoid direct contact between the positive (+) and negative (-) terminals of the battery. Also, prevent contact between metal or conductive objects and both terminals simultaneously, as this could lead to a short circuit and severe damage.
- Polarity: Ensure the battery is correctly connected to the device. Do not reverse the positive and negative terminals. Incorrect polarity can cause severe damage to the battery and connected equipment.
- Overload Protection: Before connecting any consumer, ensure that the battery's power output can meet the consumer's requirements to avoid overloading the battery.
2. Product Overview
The LiTime 12.8V 100Ah H190 Smart LiFePO4 Battery is a high-performance, deep-cycle lithium battery designed for various applications, including RVs, marine boats, solar power systems, and more. It features advanced technology for enhanced safety, monitoring, and longevity.
Key Features:
- Bluetooth 5.0 & Intelligent BMS Monitoring: Enjoy a stable, FCC & CE RED certified Bluetooth 5.0 connection. Easily connect via barcode for real-time monitoring of State of Charge (SOC), voltage, and current via the LiTime APP (iOS/Android).
- Intelligent Low Temperature Protection: Special cold protection for the H190 smart underseat battery. Charging automatically shuts down at ≤ 0°C and resumes at > 5°C. Discharge automatically shuts down at ≤ -20°C. This reliably protects the battery from cold damage.
- High Quality Automotive Grade LiFePO4 Cells: Built with 3.2V 100Ah automotive cells, offering 1280Wh capacity. Prismatic cells ensure high compressive strength and optimal heat dissipation, contributing to over 4000 life cycles for maximum longevity.
- Comprehensive BMS Protection: Integrated Battery Management System (BMS) provides protection against overcharge, deep discharge, overcurrent, short circuit, and cold temperatures, ensuring safe continuous operation.
- Strong Performance for High Loads: Delivers 1280Wh energy and 1280W continuous power. Features 100A continuous current (charging/discharging) and a 500A peak current (for 1 second), making it ideal for demanding applications.
- Compact, Light & Mobile Home-Optimized: Weighing only 9.91 kg, it's perfect for European RVs. Offers high energy efficiency, is gas-free, and provides explosion and fire protection. It is also maintenance-free.
- System Monitoring for Series/Parallel Circuit: The dedicated LiTime APP can monitor the entire battery system when multiple batteries are connected in series or parallel.



3. Setup and Installation
3.1. Included Components
- LiTime 12.8V 100Ah H190 Smart LiFePO4 Battery
- M8-14mm Connection Screws
- Socket Wrench
- Insulating Caps
The M8-14mm connection screws are designed for attaching multiple cable lugs to a single battery terminal. These bolts can be replaced with M8 bolts of different lengths if required. The screws have a length of 14mm, a diameter of 8mm, and a pitch of 1.25mm.
3.2. Physical Installation

- Orientation: Always install the battery upright with the terminal screws pointing upwards. Avoid inverted mounting. If side mounting is necessary, contact customer support for guidance.
- Securing Terminals: Use the provided socket wrench to tighten the terminal screws. Ensure they are tightened until they can no longer be turned and the spring washer is completely flat. This prevents heat buildup from loose connections.
- Insulating Caps: After tightening the screws, cover the battery terminals with the insulating caps to prevent accidental short circuits. If an insulating cap shows signs of melting, discontinue use immediately and contact support.
3.3. Wiring Connections
- Polarity: Connect the positive (+) terminal of the battery to the positive input of your device/system, and the negative (-) terminal to the negative input. Double-check all connections to ensure correct polarity.
- Series/Parallel Connections: If connecting multiple batteries, ensure they are of the same brand and specifications. Do not mix different brands or specifications in series or parallel configurations. The battery supports up to 4P4S expansion.
- Overload Prevention: Before connecting any load, confirm that the battery's power output (1280W continuous) is sufficient for the connected device's requirements to prevent overload.
3.4. Application Examples


4. Operation
4.1. LiTime App Monitoring (Bluetooth 5.0)
The LiTime battery integrates Bluetooth 5.0, allowing for accurate and effortless real-time monitoring and management of its status via the dedicated LiTime App.

Step 1: Download and Register
Download the LiTime APP from the Apple App Store (for iOS devices) or Google Play (for Android devices). Once installed, register your account to begin using the app.
Step 2: Connect to Battery
Ensure Bluetooth is enabled on your smartphone and you are within 5-10 meters of the battery. Open the LiTime App and follow the on-screen instructions to search for and connect to your battery. The app will guide you through the device discovery and connection process.
Monitored Parameters via App:
- State of Charge (SOC)
- Current (Charging/Discharging)
- Power
- Battery Voltage
- Capacity
- Battery Temperature
- Battery On/Off Control
4.2. Low Temperature Protection
The battery features intelligent low temperature protection to prevent damage during extreme cold conditions.

- Charging Shutdown: Charging will automatically stop if the battery temperature drops to 0°C or below.
- Charging Resumption: Charging will automatically resume once the battery temperature rises above 5°C.
- Discharge Shutdown: Discharging will automatically stop if the battery temperature drops to -20°C or below.
5. Maintenance and Storage
5.1. General Maintenance
- Terminal Inspection: Regularly inspect battery terminals and connections for cleanliness, tightness, and any signs of corrosion. Clean terminals with a wire brush and a baking soda solution if corrosion is present, then rinse with water and dry thoroughly.
- Physical Inspection: Periodically check the battery casing for any physical damage, cracks, or swelling.
5.2. Long-Term Storage
For periods of extended non-use, follow these guidelines to ensure the battery's longevity:
- Charge Level: It is recommended to store the battery at approximately 50% State of Charge (SOC).
- Storage Temperature: Store the battery in a cool, dry place with a stable temperature between 10°C and 35°C. Avoid extreme temperatures.
- Recharge Frequency: Recharge the battery every three months to maintain its health and prevent deep discharge during storage.
6. Troubleshooting
If you encounter issues with your LiTime LiFePO4 battery, refer to the following troubleshooting steps:
- Melted Insulating Cap: If an insulating cap on a terminal melts, immediately discontinue using the battery. This indicates excessive heat, which can be dangerous. Contact service.de@litime.com for further analysis and support.
- Battery Not Charging:
- Check all charging cable connections for tightness and correct polarity.
- Ensure the charger is functioning correctly and provides the recommended charging voltage (14.4V ± 0.2V) and current (20A).
- Verify that the ambient temperature is within the charging range (0°C to 50°C). The battery's low-temperature charging protection will prevent charging below 0°C.
- Check the charger's output with a multimeter.
- Battery Not Discharging / Low Power Output:
- Check all load connections for tightness and correct polarity.
- Ensure the connected consumer's power requirements do not exceed the battery's continuous discharge current (100A) or continuous power (1280W).
- Verify that the ambient temperature is within the discharging range (-20°C to 60°C). The battery's low-temperature discharge protection will prevent discharging below -20°C.
- Check the battery's State of Charge (SOC) via the LiTime App. Recharge if necessary.
- LiTime App Connection Issues:
- Ensure Bluetooth is enabled on your smartphone and you are within 5-10 meters of the battery.
- Try restarting the app or your smartphone.
- Ensure the app is updated to the latest version.
- If the issue persists, try forgetting the device in your phone's Bluetooth settings and reconnecting through the app.
- Unexpected Shutdown (Overload Protection): If the battery shuts down unexpectedly, it might be due to an overload. Reduce the connected load and check all connections. The BMS will automatically protect the battery from overcurrent.
7. Technical Specifications
| Feature | Specification |
|---|---|
| Brand Name | LiTime |
| Model Number | L12V 100Ah H190 Bluetooth LiFePO4 Battery |
| Type | LiFePO4 |
| Nominal Voltage | 12.8V |
| Rated Voltage | 12V |
| Nominal Capacity | 100Ah |
| Energy | 1280Wh |
| Weight | 9.91 kg |
| Size (L x W x H) | 35.8 x 17.7 x 18.9 cm |
| Recommended Charging Specification | CC/CV | 14.4 ± 0.2 V | 20A |
| Max. Continuous Charging Current | 100A |
| Max. Continuous Discharge Current | 100A |
| Maximum Discharge Current (1 second) | 500A |
| Cycle Life | 4,000 cycles at 100% DOD, 6,000 cycles at 80% DOD, 15,000 cycles at 60% DOD |
| Max. Expansion (Parallel & Series) | 4P4S |
| Internal Resistor | ≤40 mΩ |
| Protection Class | IP65 |
| Operating Temperature (Charging) | 0°C to 50°C |
| Operating Temperature (Discharging) | -20°C to 60°C |
| Storage Temperature | -10°C to 50°C |
| Properties | Bluetooth, Low Temperature Protection |
| Certifications | FCC, CE, RoHS, UN38.3 |
| Application | Portable Freezer, Electric Sweeper, Robot Pool Cleaner, RV, Marine Boat, Trolling Motor, Home Energy, Solar Power Storage, Off-Grid Solar Power System, Others |
8. User Tips
- Initial Use: Always fully charge the battery before its first operation to ensure optimal performance and longevity.
- Safety First: When handling the battery, especially during installation or wiring, always wear insulating gloves to prevent electrical hazards.
- Proper Storage: For extended periods of non-use, store the battery at approximately 50% charge in a cool, dry place (10°C to 35°C) and recharge it every three months.
- Compatibility: This battery is not suitable as a starter battery for motor vehicles. Ensure it is used for its intended deep-cycle applications.
- Monitor with App: Utilize the LiTime App to regularly monitor the battery's State of Charge (SOC), voltage, current, and temperature. This helps in proactive maintenance and prevents unexpected issues.
- Secure Connections: Always ensure all terminal connections are tight and secure to prevent heat buildup and potential damage.
9. Warranty and Support
9.1. Warranty Information
The LiTime 12.8V 100Ah H190 Bluetooth LiFePO4 Battery comes with a 5-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
9.2. Customer Support
For any technical assistance, warranty claims, or questions regarding battery orientation for side mounting, please contact our dedicated support team:
- Email: service.de@litime.com
9.3. User Manual (PDF)
For comprehensive instructions, detailed diagrams, and additional information, please refer to the official user manual available in PDF format. You can access it via the following link: LiTime 12.8V 100Ah H190 User Manual (PDF).
10. Battery Disposal
Lithium-ion batteries contain materials that can be harmful to the environment if not disposed of properly. It is crucial to dispose of your LiTime battery responsibly and in accordance with local regulations.
- Local Authorities: Please consult your local authority's website or waste management services for specific guidelines on how to safely dispose of lithium-ion batteries in your area.
- Do Not Incinerate: Never incinerate the battery or dispose of it with regular household waste.
- Recycling: Look for designated battery recycling centers or programs in your community.